• Journal of the Korean Geotechnical Society
• /
• v.37 no.12
• /
• pp.107-116
• /
• 2021

In this study, a set of laboratory liquefaction test has been conducted using undisturbed samples collected from Songlim-park, Pohang where liquefaction phenomenon had been observed in 2017. Soil samples were frozen right after tube sampling to minimize the disturbances during transport, storage, and test preparation. Cyclic triaxial test has been carried out to evaluate the liquefaction resistance ratio of undisturbed soil samples. As a result, the liquefaction resistance ratio of samples collected from 8.0~8.8 m and 11.0~11.8 m were almost similar, and these values were approximately 0.04~0.07 larger than values estimated by simplified assessment method using field test results. It is expected that the application of undisturbed sample for the evaluation of liquefaction resistance could contribute to the economical design of geotechnical structures.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.6
• /
• pp.421-427
• /
• 2022

This study was to examine the effect of lower extremity muscle strengthening exercise on balance and fall efficacy in middle older adults women. This study was conducted with one group pre-test and post-test design. A total of 34 older adults women participated in 7 weeks of intervention. Data were analyzed as SPSS ver. 21.0 using descriptive statistics and paired t-test. Right leg balance(t=6.09, p<.001), left leg balance(t=6.76, p<.001), and fall efficacy(t=6.81, p<.001) were significantly increased. Dynamic balance(t= -4.68, p=.001) was significantly decreased. This study found that lower extremity muscle strengthening exercise program could be a useful health promotion method.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.11
• /
• pp.1457-1462
• /
• 2021

Untact order payment has become a new normal since the COVID-19. BLE beacon is a technology that supports low-power wireless communication within 70 meters without Bluetooth pairing and is specialized for indoor positioning. Therefore, it is suitable for building and providing O2O services beyond B2C and B2B services. However, beacons have a lower utilization rate because they have fewer platforms than wifi that support long-distance wireless communication. Therefore, this paper aims to provide more convenient non-face-to-face related services than before by designing and proposing an O2O service platform using BLE beacons. When scanning beacons, not only does it receive advertising data that beacons have, but it also ensures that the actual distance between the user's terminal and beacons is accurately calculated. Through accurate location, the O2O service platform will be able to provide users with store information, such as coupons and discounts, museum exhibits, and traffic information at the right time.

• The Journal of Advanced Prosthodontics
• /
• v.15 no.1
• /
• pp.11-21
• /
• 2023

PURPOSE. To compare the sagittal condylar inclination (SCI) in dentate individuals measured by the different methods with mechanical articulator (MA), virtual articulator (VA), and a jaw tracking device (JTD) system. MATERIALS AND METHODS. A total of 22 healthy dentate participants were enrolled in this study. For MA workflow, the SCI was obtained by a semi-adjustable articulator with protrusive interocclusal records. The SCI was also set on a VA by aligning intraoral scan (IOS) with cone beam computed tomography (CBCT) and facial scan (FS), respectively. These virtual workflows were conducted in a dental design software, namely VAI_OS-CBCT and VAI_OS-FS. Meanwhile, a JTD system was also utilized to perform the measurement. Intraclass correlation was used to assess the repeatability within workflows. The bilateral SCI values were compared by Wilcoxon matched-pairs signed rank test for each workflow, and Kruskal-Wallis test and post hoc p-value Bonferroni correction were used to compare the differences among four workflows. The agreement of VAI_OS-CBCT, VAI_OS-FS, and JTD compared with MA was evaluated by Bland-Altman analysis. RESULTS. Intraclass correlation of the SCI revealed a high degree of repeatability for each workflow. There were no significant differences between the left and right sides (P > .05), except for VAI_OS-CBCT (P = .028). Significant differences were not found between MA and VAI_OS-FS (P > .05). Bland-Altman plots indicated VAI_OS-CBCT, VAI_OS-FS, and JTD were considered to substitute MA with high 95% limits of agreement. CONCLUSION. The workflow of VAI_OS-FS provided an alternative approach to measure the SCI compared with MA.

• Design & Manufacturing
• /
• v.16 no.4
• /
• pp.34-39
• /
• 2022

Sustained economic development around the world is accelerating resource depletion. Research and development of secondary batteries that can replace them is also being actively conducted. Secondary batteries are emerging as a key technology for carbon neutrality. The core of an electric vehicle is the battery (secondary battery). Therefore, in this study, the temperature change by the heat source of the hammer and the rotational speed (rpm) of the abrasive disc of the Classifier Separator Mill (CSM) was repeatedly calculated and analyzed using the heat flow simulation STAR-CCM+. As the rotational speed (rpm) of the abrasive disk increases, the convergence condition of the iteration increases. Under the condition that the inlet speed of the Classifier Separator Mill (CSM) and the heat source value of the disc hammer are the same, the disc rotation speed (rpm) and the hammer temperature are inversely proportional. As the rotational speed (rpm) of the disc increases, the hammer temperature decreases. However, since the wear rate of the secondary battery material increases due to the strong impact of the crushing rotational force, it is determined that an appropriate rpm setting is necessary. In CSM (Classifier Separator Mill), it is judged that the flow rate difference is not significantly different in the direction of the pressure outlet (Outlet 1) right above the classifier wheel with the fastest flow rate. Because the disc and hammer attachment technology is adhesive, the attachment point may deform when the temperature of the hammer rises. Therefore, it is considered necessary to develop high-performance adhesives and other adhesive technologies.

• Journal of Sport and Applied Science
• /
• v.7 no.2
• /
• pp.39-51
• /
• 2023

Purpose: The purpose of this study was to investigate differences in the control process to satisfy spatial and temporal constraints imposed upon the anticipation timing response by analyzing the effect of spatio-temporal accuracy demands on eye movements, response accuracy, and the coupling of eye and hand movements. Research design, data, and methodology: 12 right-handed male subjects participated in the experiment and performed anticipation timing responses toward a stimulus moving at three velocities (0.53m/s, 0.66m/s, 0.88m/s) in two task constraint conditions (temporal constraint, spatial constraint). During the response, response accuracy and eye movement patterns were measured from which timing and radial errors, the latency of saccade, fixation duration of the point of gaze (POG), distance between the POG and stimulus, and spatio-temporal coupling of the POG and hand were calculated. Results: The timing and radial errors increased with increasing stimulus velocity, and the spatio-temporal constraints led to larger timing errors than the temporal constraints. The latency of saccade and the temporal coupling of eye and hand decreased with increasing stimulus velocity and were shorter and longer respectively in the spatio-temporal constraint condition than in the temporal constraint condition. The fixation duration of the POG also decreased with increasing stimulus velocity, but no difference was shown between task constraint conditions. The distance between the POG and stimulus increased with increasing stimulus velocity and was longer in the temporal constraint condition compared to the spatio-temporal constraint condition. The spatial coupling of eye and hand was larger with the velocity 0.88m/s than those in other velocity conditions. Conclusions: These results suggest that differences in eye movement patterns and spatio-temporal couplings of stimulus, eye and hand by task constraints are closely related with the accuracy of anticipation timing responses, and the spatial constraints imposed may decrease the temporal accuracy of response by increasing the complexity of perception-action coupling.

• Composites Research
• /
• v.22 no.2
• /
• pp.37-42
• /
• 2009

This paper presents an experimental approach to design a bending-type actuator by using a shape memory alloy wire (SMA), composite strip, and spring. The SMA wire is attached to two edges of the bent strip to apply pre-stress to the SMA wire. The spring is used to provide recovery force right after actuation of the SMA wire. To investigate thermo-mechanical characteristics of the SMA wire, a series of DSC tests have been conducted and tensile tests under various levels of pre-stress and input power have been performed. Based on the measured properties of the SMA wire, bending-type actuators are designed and tested for different combination of strip, number of springs, and input power. It has been found that a bending-type actuator with a proper combination shows fast actuation performance and low power consumption.

• Journal of Technologic Dentistry
• /
• v.45 no.1
• /
• pp.1-7
• /
• 2023

Purpose: To evaluate the marginal and internal fit of metal coping fabricated by a metal three-dimensional (3D) printer that uses selective laser melting (SLM). Methods: An extraoral scanner was used to scan a die of the prepared maxillary right first molar, and the coping was designed using computer-aided design software and saved as an stereo lithography (STL) file. Ten specimens were printed with an SLM-type metal 3D printer (SLM group), and 10 more specimens were fabricated by casting the castable patterns output generated by a digital light processing-type resin 3D printer (casting the 3D printed resin patterns [CRP] group). The fit was measured using the silicon replica technique, and 8 points (A to H) were set per specimen to measure the marginal (points A, H) and internal (points B~G) gaps. The differences among the groups were compared using the Mann-Whitney U-test (α=0.05). Results: The mean of marginal fit in the SLM group was 69.67±18.04 ㎛, while in the CRP group was 117.10±41.95 ㎛. The internal fit of the SLM group was 95.18±41.20 ㎛, and that of the CRP group was 86.35±32 ㎛. As a result of statistical analysis, there was a significant difference in marginal fit between the SLM and CRP groups (p<0.05); however, there was no significant difference in internal fit between the SLM group and the CRP group (p>0.05). Conclusion: The marginal and internal fit of SLM is within the clinically acceptable range, and it seems to be applicable in terms of fit.

• Journal of the Korean Institute of Rural Architecture
• /
• v.24 no.4
• /
• pp.133-139
• /
• 2022

This study deals with the formation of Jongyeonbangjeok's Gwangju Factory in the 1930's to 80's, and the findings are shown below: In the period of formation, the factory was rectangular-shaped from north to south, and the structure was located at the center of the site, and in the east of it, there was a dormitory connected from south to north. The building was arranged with an open area on the south. In the east of the site where company houses were located, same-sized structures were arranged along the axis.In the period of change, the factory was restored about the damage from the Korean War, and it went through the process of division into two companies. As a result, the factory in the center of the site was divided into left and right ones, and the dormitory and the group of company houses were, too, divided into two, so division was made largely into southern and northern parts. In the period of stabilization, along with factory extension in each of the companies, welfare for factory workers was expanded by building more houses or opening sport facilities. After the 1980's, too, the existing factories were either extended or remodeled according to the induction of equipment, and some showed changes in their functions due to a fire or such.

• The Korean Journal of Franchise Management
• /
• v.9 no.2
• /
• pp.17-29
• /
• 2018

Purpose - The environment surrounding the franchise industry in recent years is a big threat to the franchise business. In this perspective, this study examines the effect of franchise CEO's Innovation, CSR Passion, and customer orientation(CO) on customers' perceived service quality(PSQ), affection, and commitments in the context of food-service franchise industry. This study suggests the guidelines on how franchisor uses their passion and customer orientation on customer to maintain and increase the commitments. Research design, data, and methodology - In order to achieve these purposes, research model and hypotheses were developed. Out of 500 respondents received through online survey, 449 respondents were used, because of 51 incomplete respondents. The data were analyzed using frequency analysis, confirmatory factor analysis, correlation analysis, and structural equational modeling with SPSS 23.0 and AMOS 23.0 statistical program. Result - The results of the study are as follows. First, innovation passion has a significant impact on PSQ and customer affection. And CSR passion have a significant impact on PSQ. Second, customer orientation has a significant impact on PSQ and customer affection. Third, PSQ has a significant impact on customer affection and sustainable commitment. Fourth, customer affection has a significant impact on behavioral commitment. Fifth, behavioral commitment has a significant impacts on sustainable commitment. Conclusions - The implications of this study are following as: Restaurants franchisor and CEOs should have a passion for innovation to continuously identify consumer needs and develop new menus and services that meet their needs. Second, franchisor and CEOs need to demonstrate the importance of creating the right environment, creating a fair business, and trying to create products in a given environment. Finally, franchisor and CEOs should demonstrate how to build relationships with customers and how to maintain positive feelings. In addition, it is necessary to appeal to the customers with enthusiasm and a customer-oriented tendency of the entrepreneur of the franchise head office in order to maintain the relationship with the customer and feelings.