• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Asia pacific journal of information systems
• /
• 제24권4호
• /
• pp.443-472
• /
• 2014

To survive in the global competitive environment, enterprise should be able to solve various problems and find the optimal solution effectively. The big-data is being perceived as a tool for solving enterprise problems effectively and improve competitiveness with its' various problem solving and advanced predictive capabilities. Due to its remarkable performance, the implementation of big data systems has been increased through many enterprises around the world. Currently the big-data is called the 'crude oil' of the 21st century and is expected to provide competitive superiority. The reason why the big data is in the limelight is because while the conventional IT technology has been falling behind much in its possibility level, the big data has gone beyond the technological possibility and has the advantage of being utilized to create new values such as business optimization and new business creation through analysis of big data. Since the big data has been introduced too hastily without considering the strategic value deduction and achievement obtained through the big data, however, there are difficulties in the strategic value deduction and data utilization that can be gained through big data. According to the survey result of 1,800 IT professionals from 18 countries world wide, the percentage of the corporation where the big data is being utilized well was only 28%, and many of them responded that they are having difficulties in strategic value deduction and operation through big data. The strategic value should be deducted and environment phases like corporate internal and external related regulations and systems should be considered in order to introduce big data, but these factors were not well being reflected. The cause of the failure turned out to be that the big data was introduced by way of the IT trend and surrounding environment, but it was introduced hastily in the situation where the introduction condition was not well arranged. The strategic value which can be obtained through big data should be clearly comprehended and systematic environment analysis is very important about applicability in order to introduce successful big data, but since the corporations are considering only partial achievements and technological phases that can be obtained through big data, the successful introduction is not being made. Previous study shows that most of big data researches are focused on big data concept, cases, and practical suggestions without empirical study. The purpose of this study is provide the theoretically and practically useful implementation framework and strategies of big data systems with conducting comprehensive literature review, finding influencing factors for successful big data systems implementation, and analysing empirical models. To do this, the elements which can affect the introduction intention of big data were deducted by reviewing the information system's successful factors, strategic value perception factors, considering factors for the information system introduction environment and big data related literature in order to comprehend the effect factors when the corporations introduce big data and structured questionnaire was developed. After that, the questionnaire and the statistical analysis were performed with the people in charge of the big data inside the corporations as objects. According to the statistical analysis, it was shown that the strategic value perception factor and the inside-industry environmental factors affected positively the introduction intention of big data. The theoretical, practical and political implications deducted from the study result is as follows. The frist theoretical implication is that this study has proposed theoretically effect factors which affect the introduction intention of big data by reviewing the strategic value perception and environmental factors and big data related precedent studies and proposed the variables and measurement items which were analyzed empirically and verified. This study has meaning in that it has measured the influence of each variable on the introduction intention by verifying the relationship between the independent variables and the dependent variables through structural equation model. Second, this study has defined the independent variable(strategic value perception, environment), dependent variable(introduction intention) and regulatory variable(type of business and corporate size) about big data introduction intention and has arranged theoretical base in studying big data related field empirically afterwards by developing measurement items which has obtained credibility and validity. Third, by verifying the strategic value perception factors and the significance about environmental factors proposed in the conventional precedent studies, this study will be able to give aid to the afterwards empirical study about effect factors on big data introduction. The operational implications are as follows. First, this study has arranged the empirical study base about big data field by investigating the cause and effect relationship about the influence of the strategic value perception factor and environmental factor on the introduction intention and proposing the measurement items which has obtained the justice, credibility and validity etc. Second, this study has proposed the study result that the strategic value perception factor affects positively the big data introduction intention and it has meaning in that the importance of the strategic value perception has been presented. Third, the study has proposed that the corporation which introduces big data should consider the big data introduction through precise analysis about industry's internal environment. Fourth, this study has proposed the point that the size and type of business of the corresponding corporation should be considered in introducing the big data by presenting the difference of the effect factors of big data introduction depending on the size and type of business of the corporation. The political implications are as follows. First, variety of utilization of big data is needed. The strategic value that big data has can be accessed in various ways in the product, service field, productivity field, decision making field etc and can be utilized in all the business fields based on that, but the parts that main domestic corporations are considering are limited to some parts of the products and service fields. Accordingly, in introducing big data, reviewing the phase about utilization in detail and design the big data system in a form which can maximize the utilization rate will be necessary. Second, the study is proposing the burden of the cost of the system introduction, difficulty in utilization in the system and lack of credibility in the supply corporations etc in the big data introduction phase by corporations. Since the world IT corporations are predominating the big data market, the big data introduction of domestic corporations can not but to be dependent on the foreign corporations. When considering that fact, that our country does not have global IT corporations even though it is world powerful IT country, the big data can be thought to be the chance to rear world level corporations. Accordingly, the government shall need to rear star corporations through active political support. Third, the corporations' internal and external professional manpower for the big data introduction and operation lacks. Big data is a system where how valuable data can be deducted utilizing data is more important than the system construction itself. For this, talent who are equipped with academic knowledge and experience in various fields like IT, statistics, strategy and management etc and manpower training should be implemented through systematic education for these talents. This study has arranged theoretical base for empirical studies about big data related fields by comprehending the main variables which affect the big data introduction intention and verifying them and is expected to be able to propose useful guidelines for the corporations and policy developers who are considering big data implementationby analyzing empirically that theoretical base.

• 사상체질의학회지
• /
• 제11권2호
• /
• pp.119-150
• /
• 1999

동(東) 서양의학(西洋醫學)이 여러 방면(方面)으로 눈부시게 발전(發展)해 왔음에도 불구(不拘)하고 동일질병(同一疾病)에 대한 약(藥) 효과(效果)의 개인별(個人別) 차이(差異)나 질병(疾病)에 대한 개인별(個人別) 감수성(感受性)의 차이(差異)에 따른 여러 가지 면역관계(免疫關係) 질환(疾患)의 다양성(多樣性)이나 난치병(難治病)의 다양(多樣)한 예후(豫後) 등(等)의 이유(理由)를 정확(正確)히 이해(理解)하지 못하고 따라서 적절(適切)한 대처(對處)를 하지 못하고 있는 것이 현실(現實)이다. 그런데 사상의학(四象醫學)의 네 체질(體質)에 따른 질병(疾病) 관리(管理), 치료(治療) 및 예방법(豫防法)은 현대(現代)의 난치병(難治病)이라고 할 수 있는 성인병(成人病), 면역계(免疫係) 질환(疾患), 스트레스성(性) 질환(疾患)의 관리(管理)에 효과적(效果的)으로 적용(適用)할 수 있으므로 현재(現在) 한방임상의학(韓方臨床醫學)에서 많이 응용(應用)되고 있다. 이러한 사상의학(四象醫學)을 세계(世界)에 폭넓게 적용하기 위해서는 국제적(國際的)으로 응용(應用)할 수 있는 체질진단(體質診斷)의 기준(基準)이 마련되어야 한다. 우선(于先) 본(本) 연구(硏究)는 외국인(外國人)에게도 과연(果然) 체질(體質)이 존재(存在)할까 하는 의문점(疑問点)을 해결(解決)하기 위(爲)하여 미국인(美國人)을 대상(對象)으로 체질(體質) 분류(分類)를 시도하여 체질(體質) 존재(存在) 여부(與否)를 확인(確認)하는 작업(作業)부터 시작(始作)하였다. 또 체질(體質)이 존재(存在)한다면 체질(體質) 진단(診斷) 도구(道具)로는 어떤 것이 좋을까를 알아보기 위(爲)한 연구(硏究)를 병행(竝行)하였다. 선택(選擇)된 체질(體質) 진단(診斷) 도구(道具)로는 경희대학교(慶熙大學校) 사상의학(四象醫學) 교실(敎室)에서 개발(開發)되어 학회(學會)에서 공인후(公認後) 임상(臨床)에서 널리 사용(使用)되는 체질(體質) 진단(診斷) 도구(道具)인 QSCCII를 바탕으로 이를 영문(英文)으로 번역(飜譯)하고 채점(採點) 방법(方法)을 보완(補完)하여 새롭게 제작(製作)된 new QSCCII + 사용(使用)하였다. 본(本) 연구(硏究)는 국내(國內)에서 표준화(標準化)되어 사용(使用)하고 있는 체질진단진단도구(體質診斷診斷道具)인 QSCCII를 보완하여 미국(美國)에서 응용(應用)할 수 있는 새로운 진단(診斷) 도구(道具)를 마련하고자 처음으로 시도(試圖)된 연구(硏究)이다. 조사(調査) 대상(對象)은 University of Bridgeport. Connecticut. U.S.A의 학생(學生), 교직원(敎職員)그리고 Health Science Center의 Clinic을 방문(訪問)한 사람중(中) 본(本) 조사(調査)에 협력(協力)한 사람이 주(主)로 그 대상(對象)이 되었으며 기타(其他) 주변(周邊)의 현지인(現地人)들이 대상(對象)이 되었다. 년(年) 조사대상인원(調査對象人員) 344명(名)이었고 전체(全體) 조사(調査) 대상(對象)에서 재검사(再檢査)를 할 수 있었던 인원(人員)은 240명(名)이었다. 연구기간(硏究期間)은 1998년(年) 9월(月)부터 1999년(年) 8월(月)까지 약(約) 1년(年) 여(餘)에 걸쳐 실시(實施)되었다. 이러한 연구결과(硏究結果)를 고찰(考察)해 볼 때 아래와 같은 결론(結論)을 얻었다. 1. 미국(美國) 사람에게도 사상체질(四象體質)은 존재(存在)한다. 추론(推論)컨데 미국(美國)에는 다양(多樣)한 인종(人種)이 섞여 살고 있으므로 외국인(外國人) 모두에게 역시(亦是) 체질(體質)이 존재(存在)한다고 볼 수 있다. 2. 미국인(美國人)에게 특(特)히 백인(白人)에게선 소양인(少陽人)으로 진단(診斷)되는 경향(傾向)이 높았다. 이 결과(結果)는 미국(美國)사람에게도 사상체질(四象體質)은 존재(存在)한다는 가설(假說)과 다소(多少) 부합(附合)된다 사료(思料)된다. 3. 검사재검사(檢査再檢査)를 통하여 분석(分析)된 결과(結果)를 볼 때 그 결과(結果)가 일관(一貫)되게 나오는 것으로 보아 new QSCCII +가 외국인(外國人)의 체질(體質)을 진단(診斷)할 때 일관(一貫)된 결과(結果)를 얻을 수 있는 진단방법(診斷方法)일 가능성(可能性)을 시사(示唆)한다. 4. 표준(標準) 집단(集團)의 체질(體質) 분류(分類)에서는 인종(人種)에 관계(關係)없이 체질(體質)이 존재(存在)하고 있었다. 5. 반응(反應) 빈도(頻度)가 낮은 문항(問項)은 미국인(美國人)을 위(爲)한 표준화(標準化) 연구(硏究)를 할 때 미국인(美國人)에게 이해(理解)가 될 수 있는 또다른 표현(表現)으로 바꾸어 적용(適用)해 볼 필요(必要)가 있을 것으로 추정(推定)된다. 6. 미국인(美國人)의 체질(體質)을 정확(正確)하게 하기 위(爲)해서는 표준화(標準化) 작업(作業)을 함으로써 QSCCII라는 진단도구(診斷道具)를 이용(利用)하여 측정(測定) 진단(診斷) 데이터를 평가(評價)할 수 있는 진단(診斷) 기준(基準)이 만들어져야 한다. 7. 체질(體質)이 불투명(不透明)하다고 나온 71명(名) 중(中)에는 잠재적(潛在的) 태양인체질(太陽人體質)이 포함(包含)되어 있을 것으로 추정(推程)되나 태양인(太陽人)의 희소성(稀少性)에서 기인(起因)하는 new QSCCII+의 변별력저하(辨別力低下)에 대한 해결방안(解決方案)에 대(對)한 연구(硏究)가 추후(追後)에 진행(進行)되어야 할 것으로 사료(思料)된다. 8. 연구결과(硏究結果) 북미지역(北美地域)의 체질분포(體質分布)는 다음과 같다. 연인원(年人員)을 대상(對象)으로한 분포(分布)에서는 소양인(少陽人) 36.25 %(87명), 태음인(太陰人) 13.75 %(33명(名)), 소음인(少陰人) 20.41%(49 명(名)), 분류(分類)가 안되거나 태양인(太陽人)인 경우(境遇)가 29.58%(71 명(名))이었다.

• 한국산림과학회지
• /
• 제64권1호
• /
• pp.11-19
• /
• 1984

외생균근(外生菌根)을 형성(形成)하는 모래밭버섯균(Pisolithus tinctorius) (Pt)을 대상(對象)으로 토성(土性)의 변화(變化)와 퇴비(堆肥)의 첨가(添加)로 인(因)한 토양비옥도(土壤肥沃度)의 변화(變化)에 따른 공생균(共生菌)으로써의 생장촉진효율(生長促進效率)을 조사(調査)하였다. Pt균(菌)을 vermiculite-peat moss-영양액(營養液)에 균사형태(菌絲形態)로 배양(培養)하여 세가지 토성(土性)((사토(砂土) 양질사토(養質砂土), 사질양토(砂質壤土)), 퇴비(堆肥)의 첨가유무(添加有無), 균근균(菌根菌)의 종류(種類)(Pt균(菌), 천연(天然) 균근균(菌根菌), 무균근(無菌根))에 따른 요인시험설계(要因試驗設計)에 맞추어서, 소독(消毒)된 흙 속에 접종(接種)하였다. 접종(接種)된 흙을 $4{\ell}$ 용량(容量)의 플라스틱 화분(花盆)에 담고 4개의 리기테다소나무(Pinus rigida ${\times}$ P. taeda) 종자(種子)를 파종(播種)하고 온실(溫室)에서 사개월간(四個月間) 생육(生育)시켰다. 수확후(收穫後)에 처리간(處理間)에 묘고(苗高), 건중량(乾重量), 균근형성율(菌根形成率), 질소함량(窒素含量), T/R율(率)을 조사(調査)하였다. 토성(土性), 토양비옥도(土壤肥沃度), 퇴비첨가유무((堆肥添加有無)에 관계(關係)없이, Pt로 접종(接種)된 묘목(苗木)은 천연균근균(天然菌根菌)으로 (토양(土壤) 소독(消毒)없이 천연적(天然的)으로 형성(形成)된 균근(菌根)) 접종(接種)된 묘목(苗木)이나 무균근묘목(無菌根苗木)(토양소독(土壤消毒)만 실시(實施))보다 묘고생장(苗高生長)과 건중량(乾重量)에서 훨씬 더 컸다. 그러나 가장 토양비옥도(土壤肥沃度)가 높은 토양(土壤)(퇴비(堆肥)가 첨가(添加)된 사질양토(砂質壤土), 질소(窒素) 0.075%, 유기물(有機物) 1.32%) 에서는 무균근묘목(無菌根苗木)이 Pt묘목(苗木)보다 묘고(苗高)에서 8%, 건중량(乾重量)에서 18% 더 좋았다. 전체(全体) 평균(平均)으로 볼 때 Pt묘목(苗木)은 천연균근묘목(天然菌根苗木)보다 묘고(苗高)에서 30%, 건중량(乾重量)에서 107% 더 컸으며, 무균근묘목(無菌根苗木)보다 묘고(苗高)에서 31%, 건중량(乾重量)에서 60% 더 컸다. 토양비옥도(土壤肥沃度)가 낮고 퇴비(堆肥)가 첨가(添加)되지 않았을 때, Pt균(菌)에 의(依)한 생장촉진효과(生長促進效果)가 더 크게 나타났다. 균근형겅빈도(菌根形成頻度)는 퇴비첨가(堆肥添加)로 Pt의 경우에 절반(折半)으로 사질양토(砂質壤土) 경우(境遇)에 84에서 33%로, 양질사토(養質砂土)의 경우(境遇)에 77에서 40%로) 줄었으나, 천연균근균(天然菌根菌)의 경우(境遇)에는 줄지 않았다. 무균근묘목(無菌根苗木)은 심(甚)한 질소결핍현상(窒素缺乏現像)(1.38%N)을 일으킨 반면(反面)에, Pt접종묘목(接種苗木)(1.68%N)과 천연균근묘목(天然菌根苗木)(1.89% N)은 정상적(正常的)이었다. 이로 미루어 보아서 균근균(菌根菌)은 토양내(土壤內) 질고(窒素)의 흡수(吸收)를 촉진(促進)한다고 생각된다. T/R율(率)은 퇴비첨가(堆肥添加)로 인(因)하여 증가(增加)하였으나, 균근균(菌根菌)의 종류(種類)나 그 존재유무(存在有無)로 인(因)하여 영향(影響)을 받지 않았다. 모래밭버섯균의 생장촉진효율(生長促進效率)은 비옥도(肥沃度)에 의(依)하여 결정(決定)된다고 결론(結論)지을 수 있다. 즉 비옥도(肥沃度)가 낮은 사질토(砂質土)에서 퇴비(堆肥)를 첨가(添加)하면 Pt의 효율(效率)이 크게 나타나지만, 비옥도(肥沃度)가 더 높은 사질양토(砂質壤土)에 퇴비(堆肥)를 첨가(添加)하면 Pt의 효율(效率)이 적게 나타난다. 모래밭버섯균의 이점(利點)은 퇴비(堆肥)를 첨가(添加)하지 않을 경우(境遇)와 토양(土壤)의 비옥도(肥沃度)가 높지 않을때 더 크게 나타날 것이라고 생각된다.

• 한국가금학회지
• /
• 제35권2호
• /
• pp.143-151
• /
• 2008

본 실험은 사료 내 칼슘 수준과 fungal phytase의 상호 관계를 구명하고자 21주령 HyLine Brown 산란계 720수를 공시하여 시험을 실시하였다. 시험구는 phytase 첨가 수준 0, 300, 1000 DPU/kg, 칼슘 2수준(3.5, 4.0%), 무기태 인 수준 무첨가(0.095 NPP), 0.5(0.185 NPP), 1.0%(0.275%)를 조합한 $3{\times}2{\times}3$ 요인 시험으로 하였다. 실험 사료는 CP 16%에 ME 2,800 kcal/ kg 수준으로 급여하였다. 사료는 실험 전 기간 자유 채식토록 하였으며, 점등은 17시간으로 하였다. 조사 항목은 산란계의 생산 능력, 계란의 품질이다. 산란율은 fungal phytase 300 DPU 첨가구에서 증가하는 경향을 보였으며, 연.파란율은 감소하는 경향을 보였다. 처리구간별 산란율은 사료의 칼슘 수준에 따른 차이가 없었지만, NPP 무첨가구인 0.095% 첨가구에서 다른 처리구에 비하여 낮았다(P<0.05). 평균 난중 및 1일 산란량은 fungal phytase 300 DPU 첨가구에서 가장 높게 나타났다. 평균 난중은 사료 칼슘 수준이 3.5% 처리구에서 높게 나타났지만(P<0.05) 1일 산란량은 처리구간에 차이가 없었다. 평균 난중 및 1일 산란량은 NPP 무첨가구인 0.095% 첨가구에서 다른 처리구에 비하여 매우 낮았다(P<0.05). 사료 섭취량은 사료의 fungal phytase 및 칼슘 수준에 관계없이 비슷한 경향을 보였지만, 사료내 NPP 0.275, 0.165% 함유된 처리구에서 0.095% 처리구보다 통계적으로 높게 나타났다(P<0.05). 사료 요구율은 사료내 칼슘 및 NPP 수준간에 차이가 없었지만, fungal phytase 300DPU 첨가구에서 가장 크게 개선되었다(P<0.05). 난각 강도와 두께는 사료의 칼슘 수준이 높을수록 향상되는 결과를 보였고, NPP 0.275, 0.165%가 함유된 처리구에서 0.095% 처리구에 비하여 향상되었으며, 사료내 fungal phytase 수준에 따른 차이는 없었다. Haugh unit은 처리구간에 큰 차이 없이 비슷하게 나타났다. 본 실험의 결과, 산란계 사료에서 fungal phytase의 적정 수준은 300 DPU이며, 이때 사료내 TCP 첨가량은 권장량 대비 40% 이상 저감 효과가 있었으며, 사료의 칼슘 수준을 높게 하였을지라도 fungal phytase 첨가에 대한 개선 효과는 나타나지 않았다.

• 한국전통조경학회지
• /
• 제34권3호
• /
• pp.78-97
• /
• 2016

본 연구는 문헌 및 현장조사를 바탕으로 양평군 서종면 벽계천에 형성된 수회구곡과 벽계구곡 그리고 노산팔경의 설정 경위를 검토하고, 화서 당대에 향유되고 경영된 명승 벽계의 경관실체를 구명하는 것을 목적으로 한다. 연구의 결과는 다음과 같다. 첫째, 화서 이항로 이후에 설정된 벽계구곡과 노산팔경은 화서의 행적과 관련된 주요 경처를 모은 '현대기(現代期)'의 집경으로 판명되었다. 벽계구곡이 수회구곡의 집경요소와 많은 부분 중복되는 점이나, 수회구곡의 종점부터 노산팔경의 영역이 시작되는 작위적 구성은 수입리 벽계와 노문리 벽계 사이의 장소대립 및 장소패권의 양상을 엿보게 한다. 이는 화서 이전 벽계 향유집단의 오랜 역사성과 화서의 이미지로 밀착된 영역성이 상충되어 나타난 결과로 판단된다. 둘째, 벽계구곡은 노산팔경의 영역을 확대함과 동시에 수입리의 경승을 선별해 재구성한 2차적 공간체계였다. 벽계구곡의 설정 이후 벽계천 전체 권역에 대한 장소 정체성이 효과적으로 확보되었는데, '청서구장(淸西舊莊)'과 '수회구곡(水回九曲)' 바위글씨 등 화서 이전의 명소가 철저히 배제되는 등 '화서 지향적' 공간 성격을 갖고 있었다. 그 결과 노문리뿐만 아니라 수입리에 이르는 벽계천 전체 영역은 화서의 문화경관으로 재편되었다. 셋째, '주자-율곡-우암-화서'로 이어지는 도통 강화의 일환으로 설정된 화서학파의 구곡 설정은 벽계구곡 탄생의 계기이자 외적 동인이 되었다. 즉, 벽계구곡과 노산팔경은 화서학의 중심이 옥계동으로 건너간 것에 대한 반동, 무이구곡 고산구곡과 옥계구곡의 사이의 결손된 도체공간의 창출 그리고 후손과 지역민에 의한 화서 선양작업 등 일련의 전략적 지향성과 흐름을 같이 한다. 넷째, 화서의 주리론적 관점에서 살펴보면, 그가 경영한 벽원(蘗園)의 모든 경역은 '실제로 존재하는 산수경치의 물상[氣]'을 통해 리(理)의 내재함과 심미적 자아의 허령(虛靈)한 경계를 체험하는 공간작법으로 존재했음을 알 수 있다. 이러한 점은 벽계구곡이나 노산팔경을 화서와 연관된 영역으로 조명하기 이전에, 벽원 고유의 경관성을 규정짓고 나아가 어떤 방식으로 접근하고 향유해야 하는지를 일깨워 준다. 다섯째, 노산팔경은 벽계구곡 중 노문리 벽계 일원 중에서도, 화서가 강학하고 소요하던 여덟 곳의 경승을 담는 곡중경(曲中景)의 문화경관으로 구성되었으나 화서가 남긴 바위글씨와 시문에 의존해 집경됨으로써 벽계구곡에 비해 내적 충일성은 확보되지만 집경에 따른 개념적 타당성에는 다소의 의문이 남는다.

• 한국조경학회지
• /
• 제41권6호
• /
• pp.52-61
• /
• 2013

본 연구는 여름철 낮 그늘시렁의 차양이 온열쾌적 지표에 미치는 영향을 파악하고자 수행하였다. 이를 위해 여름철 차양 및 겨울철 방풍을 고려하여 갈대발로 천개면 등을 차폐한 3가지 유형의 그늘시렁(가로 4m${\times}$세로 4m${\times}$높이 2.7m) I(천개면 차폐) II(천개면, 서향면 차폐) III(천개면, 서향면, 북향면 차폐)을 4층 옥상에 구축하였다. 그리고 1차 실험은 2013년 8월 14일부터 16일까지 대조구, 그늘시렁 I, III을 대상으로, 2차 실험은 2013년 8월 26일부터 28일까지 대조구, 그늘시렁 I, II를 대상으로 기상변수(기온, 습도, 복사, 풍속)를 측정하였다. 그늘시렁의 차양이 인체가 흡수하는 복사환경과 $T_{mrt}$ 및 $SET^*$에 미치는 영향은 다음과 같다. 그늘시렁의 차양으로 인해 인체가 흡수한 복사량의 저감은 단파복사가 장파복사에 비해 훨씬 크게 나타났다. 대조구 대비 인체가 흡수한 단파복사량 차이의 최댓값 ${\Delta}K_{abs,max}$는 그늘시렁 I과 III에서는 $-119W/m^2$와 $-158W/m^2$였으며, 그늘시렁 I과 II에서는 $-145W/m^2$와 $-159W/m^2$였다. 대조구 대비 인체가 흡수한 장파복사량의 차이의 최댓값 ${\Delta}L_{abs,max}$는 그늘시렁 I과 III에서는 $-15W/m^2$와 $-17W/m^2$였으며, 그늘시렁 I과 II에서는 $-8W/m^2$와 $-7W/m^2$였다. 그늘시렁의 차양에 의해 인체가 흡수한 $T_{mrt}$와 $SET^*$ 값도 낮아졌다. $T_{mrt}$는 1차 실험에서는 그늘시렁 I과 III에서 각각 최대 $16.0^{\circ}C$와 $21.4^{\circ}C$, 그리고 2차 실험에서는 그늘시렁 I과 II에서 각각 최대 $18.8^{\circ}C$와 $20.8^{\circ}C$ 저감되었다. $SET^*$는 1차 실험에서는 그늘시렁 I과 III에서 각각 최대 $2.9^{\circ}C$와 $2.6^{\circ}C$ 그리고 2차 실험에서는 그늘시렁 I과 II에서 각각 최대 $3.5^{\circ}C$와 $2.6^{\circ}C$ 저감되었다. 대조구 $SET^*$ 대비 그늘시렁 II, III의 $SET^*$ 저감효율은 그늘시렁 I에 비해 낮게 나타났는데, 이는 풍속의 차이 때문이었다. 따라서 그늘시렁 수직면의 차폐시에는 차양 못지않게 통풍을 고려하는 것이 필수적이라 생각된다. 대조구의 3일간 평균 최고기온이 $37.5^{\circ}C$였던 1차 실험기간 결과에서는 $SET^*$ 값이 하루 중 대부분 시간대에서 온열 쾌적대 및 수용대의 상한 값인 $28.7^{\circ}C$와 $30.4^{\circ}C$를 초과하였다. 반면에 대조구의 3일간 평균 최고기온이 $34.4^{\circ}C$였던 2차 실험결과, $SET^*$ 값이 그늘시렁 I에서는 18~12시와 오후 14~18시, 그늘시렁 II는 15~18시에만 온열 쾌적대에 드는 것으로 나타났다. 반면에 그늘시렁 I, II에서 $SET^*$ 값은 하루 중 대부분 시간대에서 온열 수용대에 드는 것으로 나타났다. 따라서 혹서기에 그늘시렁의 온열쾌적성을 확보하기 위해서는 갈대발 등에 의한 차양뿐만 아니라, 덩굴식물이나 녹음수에 의한 차양을 도입하는 방안을 강구하여야 할 것이다. 그리고 그늘시렁의 차양효과를 평가하는 지표로서 $T_{mrt}$와 $SET^*$는 실효성이 있었다고 판단되며, 향후 옥외 조경공간의 온열환경 평가 지표로서 활용이 기대된다.

• 헤리티지:역사와 과학
• /
• 제44권4호
• /
• pp.172-205
• /
• 2011

본 연구는 종합적인 현황 조사 분석을 통해 국내 돌바둑판의 위치 및 형태 그리고 입지 유형을 파악하는 한편 주변 경물과 각자 그리고 인근의 전래지명과의 관련성 분석과 해석을 통해 암각바둑판의 본질적 특성 및 장소적 의미 그리고 문화재로서의 가치 등을 파악하고자 하였다. 바둑판에 나타난 '네모난 바둑판과 둥근 바둑돌'의 천원지방적(天圓地方的) 형상, 흑백 바둑돌로 표상되는 음양조화 그리고 하늘 회전을 표현한 361로 등은 '우주적 질서가 투사(投射)된 상징체'이다. 또한 영원성을 바탕으로 바둑 삼매경에 빠진 '귤중지락(橘中之樂)'과 '상산사호(商山四皓)' 그리고 '난가(爛柯)' 모티프는 속세를 벗어난 망우청락(忘憂淸樂)의 '위기선미(圍棋仙味)'를 통해 '인생과 자연'의 관계를 시공간적으로 일치하고자 했던 천인합일의 표상이자 우미와 소요를 추구한 고아한 풍류였다. 본 연구를 통해 확인된 돌바둑판은 총본 연구는 종합적인 현황 조사 분석을 통해 국내 돌바둑판의 위치 및 형태 그리고 입지 유형을 파악하는 한편 주변 경물과 각자 그리고 인근의 전래지명과의 관련성 분석과 해석을 통해 암각바둑판의 본질적 특성 및 장소적 의미 그리고 문화재로서의 가치 등을 파악하고자 하였다. 바둑판에 나타난 '네모난 바둑판과 둥근 바둑돌'의 천원지방적(天圓地方的) 형상, 흑백 바둑돌로 표상되는 음양조화 그리고 하늘 회전을 표현한 361로 등은 '우주적 질서가 투사(投射)된 상징체'이다. 또한 영원성을 바탕으로 바둑 삼매경에 빠진 '귤중지락(橘中之樂)'과 '상산사호(商山四皓)' 그리고 '난가(爛柯)' 모티프는 속세를 벗어난 망우청락(忘憂淸樂)의 '위기선미(圍棋仙味)'를 통해 '인생과 자연'의 관계를 시공간적으로 일치하고자 했던 천인합일의 표상이자 우미와 소요를 추구한 고아한 풍류였다. 본 연구를 통해 확인된 돌바둑판은 총 18개로 이중 강진 월남사지 돌바둑판, 양산 소한정 돌바둑판, 반룡대 돌바둑판 등 3개소(16.1%)는 이동이 가능한 석국으로 분류된 반면 방학동 돌바둑판을 비롯한 15개소(83.9%)는 자연 암반에 새긴, 원래 장소를 이탈하지 않은 암각바둑판으로 밝혀졌다. 돌바둑판의 입지조건을 유형화한 결과, 계류형 15개소(83.9%), 암봉형 3개소(16.1%)로 나타났으며 가장 높은 곳에 위치한 것은 소백산 신선봉 암각바둑판(1,389m)이었다. 총 15개 돌바둑판은 모두 500m 이하의 저산지에 입지하고 있는 것으로 보아 바둑판이 새겨진 입지는 속세와 멀지 않은 생활권의 일부였으며 모두 경관성이 탁월한 계곡 및 산봉에 입지하였다. 돌바둑판은 옛 선비들의 풍류와 밀접한 관련이 있는 것으로 추찰되는바 특히 암각바둑판은 천인합일(天人合一)의 조화를 추구하며 명산대천(名山大川)을 찾아 함께 노니는 풍류도의 정신을 전승한 것으로 파악된다. 즉 궁극적으로 바둑의 전통적인 상징성인 '은일의 매개체이자 자연귀의의 도에 다다를 수 있는 선비문화의 정수'인 동시에 유선적 취향의 도구로서 자리매김 하였음을 알 수 있다. 특징적으로 암각바둑판이 새겨진 단양 소백산 신선봉을 비롯하여 괴산 선국암, 무주 사선암, 장수 신선바위 등은 신선과 관련된 지명의 일체감이 매우 높은 것으로 미루어 보아 '신선' 바위와 암각바둑판이야말로 선계에 대한 숭배와 동경의 소통방식이 가장 함축적으로 표현된 경관대상이자 조망처로 판단된다. 한편 암각바둑판이 입지하는 장소의 입지유형 등 물리적 환경과 팔경 및 동천구곡의 설정 여부, 유학자 등의 관련 여부를 중심으로 한 '인간활동' 그리고 '상산사호' 모티프 및 '난가고사' 상징의미 등 3가지를 '장소정체성 판단을 위한 해석 틀'을 기준으로 하여 고찰한 결과, 암각바둑판 주변에 각자 되어있는 동천, 동문 등의 모티프는 주자학적 '구곡팔경'의 개념 보다는 선취적 '선유동천' 개념의 공간성 모색이 필요한 것으로 보인다. 전반적으로 계류형 암각바둑판이 조성된 공간은 유가의 은둔지향적 공간이나 선도적 은일지향적 공간으로 시대추이에 따라 습합되어 온 것으로 판단되며 산봉형의 암각바둑판은 별도로 신선 강림의 숭엄지향성이 장소정체성 지배의 중요 요인으로 평가된다. 아울러 암각바둑판이 조성된 곳을 포함하여 그 주변은 동천구곡이나 팔경의 일부로 널리 알려진 승경의 요처임이 확인되었다. 또한 선비 및 사대부 계층이 주체인 주변 각자들 중에도 신선 관련 표현어가 다수 발견됨에 따라 바둑판 조영의식의 이면에는 신선경 동경을 바탕으로 한 선도적 취향이 강하게 작용하고 있음이 확인되었다. 이와 같은 결과를 총합할 때 암각바둑판은 조선조 선비들의 은일과 운둔을 통한 자연경영의 문화 현상이 집약적으로 함축된 유산이자 전래 승경의 요처로, 명승과 같은 자연문화재로서의 가치가 탁월한 대상임이 확인되었다. 현재 남한내 17개의 돌바둑판 중에서 소백산 신선봉 암각바둑판을 비롯하여 방학동 암각바둑판, 충주 사로암 암각바둑판, 무주 사선암 암각바둑판, 양산 어곡동 반룡대 석국 등은 세월의 풍파와 사람들의 접촉으로 마모되면서 바위가 깨어지거나 바둑판 줄이 희미해지고 있다. 또한 언양 반구대 집청정 암각바둑판은 토사 매몰로 그 형체를 확인하기 어려운 상태이다. 암각바둑판은 자연과 바람의 흐름을 그대로 투영한 예술적, 문화재적 가치가 탁월한 조형물이자 선인들의 자연 사랑의 마음과 선계동경의 문화가 만나 이루어진 문화유적으로, 이에 대한 국내 분포 현황에 대한 체계적인 정밀조사와 보존관리가 시급하다고 사료된다. 18개로 이중 강진 월남사지 돌바둑판, 양산 소한정 돌바둑판, 반룡대 돌바둑판 등 3개소(16.1%)는 이동이 가능한 석국으로 분류된 반면 방학동 돌바둑판을 비롯한 15개소(83.9%)는 자연 암반에 새긴, 원래 장소를 이탈하지 않은 암각바둑판으로 밝혀졌다. 돌바둑판의 입지조건을 유형화한 결과, 계류형 15개소(83.9%), 암봉형 3개소(16.1%)로 나타났으며 가장 높은 곳에 위치한 것은 소백산 신선봉 암각바둑판(1,389m)이었다. 총 15개 돌바둑판은 모두 500m 이하의 저산지에 입지하고 있는 것으로 보아 바둑판이 새겨진 입지는 속세와 멀지 않은 생활권의 일부였으며 모두 경관성이 탁월한 계곡 및 산봉에 입지하였다. 돌바둑판은 옛 선비들의 풍류와 밀접한 관련이 있는 것으로 추찰되는바 특히 암각바둑판은 천인합일(天人合一)의 조화를 추구하며 명산대천(名山大川)을 찾아 함께 노니는 풍류도의 정신을 전승한 것으로 파악된다. 즉 궁극적으로 바둑의 전통적인 상징성인 '은일의 매개체이자 자연귀의의 도에 다다를 수 있는 선비문화의 정수'인 동시에 유선적 취향의 도구로서 자리매김 하였음을 알 수 있다. 특징적으로 암각바둑판이 새겨진 단양 소백산 신선봉을 비롯하여 괴산 선국암, 무주 사선암, 장수 신선바위 등은 신선과 관련된 지명의 일체감이 매우 높은 것으로 미루어 보아 '신선' 바위와 암각바둑판이야말로 선계에 대한 숭배와 동경의 소통방식이 가장 함축적으로 표현된 경관대상이자 조망처로 판단된다. 한편 암각바둑판이 입지하는 장소의 입지유형 등 물리적 환경과 팔경 및 동천구곡의 설정 여부, 유학자 등의 관련 여부를 중심으로 한 '인간활동' 그리고 '상산사호' 모티프 및 '난가고사' 상징의미 등 3가지를 '장소정체성 판단을 위한 해석 틀'을 기준으로 하여 고찰한 결과, 암각바둑판 주변에 각자 되어있는 동천, 동문 등의 모티프는 주자학적 '구곡팔경'의 개념 보다는 선취적 '선유동천' 개념의 공간성 모색이 필요한 것으로 보인다. 전반적으로 계류형 암각바둑판이 조성된 공간은 유가의 은둔지향적 공간이나 선도적 은일지향적 공간으로 시대추이에 따라 습합되어 온 것으로 판단되며 산봉형의 암각바둑판은 별도로 신선 강림의 숭엄지향성이 장소정체성 지배의 중요 요인으로 평가된다. 아울러 암각바둑판이 조성된 곳을 포함하여 그 주변은 동천구곡이나 팔경의 일부로 널리 알려진 승경의 요처임이 확인되었다. 또한 선비 및 사대부 계층이 주체인 주변 각자들 중에도 신선 관련 표현어가 다수 발견됨에 따라 바둑판 조영의식의 이면에는 신선경 동경을 바탕으로 한 선도적 취향이 강하게 작용하고 있음이 확인되었다. 이와 같은 결과를 총합할 때 암각바둑판은 조선조 선비들의 은일과 운둔을 통한 자연경영의 문화 현상이 집약적으로 함축된 유산이자 전래 승경의 요처로, 명승과 같은 자연문화재로서의 가치가 탁월한 대상임이 확인되었다. 현재 남한내 17개의 돌바둑판 중에서 소백산 신선봉 암각바둑판을 비롯하여 방학동 암각바둑판, 충주 사로암 암각바둑판, 무주 사선암 암각바둑판, 양산 어곡동 반룡대 석국 등은 세월의 풍파와 사람들의 접촉으로 마모되면서 바위가 깨어지거나 바둑판 줄이 희미해지고 있다. 또한 언양 반구대 집청정 암각바둑판은 토사 매몰로 그 형체를 확인하기 어려운 상태이다. 암각바둑판은 자연과 바람의 흐름을 그대로 투영한 예술적, 문화재적 가치가 탁월한 조형물이자 선인들의 자연 사랑의 마음과 선계동경의 문화가 만나 이루어진 문화유적으로, 이에 대한 국내 분포 현황에 대한 체계적인 정밀조사와 보존관리가 시급하다고 사료된다.

• 한국유통학회지:유통연구
• /
• 제15권2호
• /
• pp.1-34
• /
• 2010

소비자의 구매 행위가 합리적이고 실용적인 방향으로 변화하는데 힘입어 할인점업계는 급속한 외형적인 성장과 함께 경쟁도 치열하다. 따라서 업계는 그 해결책으로 차별화와 수익성을 동시에 실현 시킬 수 있는 유통업체 브랜드(PB: Private Brand) 개발에 사활을 걸고 있다. 또한 치열한 경쟁 환경 하에서 생존하기 위해서는 고객만족을 넘어서 고객충성도를 높이는 것이 효과적인 방법임이 밝혀짐에 따라 PB가 고객충성도를 제고시키기 위한 전략적인 도구로 사용되고 있다. PB 이용 고객의 충성도를 높이려면 우선 고객집단의 특성을 파악해서 소비자가 지각하는 품질수준을 우선적으로 맞춰줘야 고객만족과 고객신뢰를 얻을 수 있고 결과적으로 고객충성도로 유도할 수 있다. 이에 본 연구는 지각된 품질에 영향을 미치는 선행요인과 고객충성도에 영향을 미치는 변수들 간의 관계에 대한 체계적인 분석결과를 제시하기 위해 선행연구에서 검증된 인과관계를 기반으로 연구모형과 연구가설을 설정했고, 주요 연구결과는 다음과 같다. 기업명성, 브랜드명성, 제품경험, 브랜드친숙도가 높을수록 지각된 품질이 높아지고, 지각된 품질이 높을수록 고객만족, 고객신뢰, 고객충성도가 높아지며, 고객만족과 고객신뢰가 높을수록 고객충성도가 높아지는 것으로 조사되었다. 또한 기업명성이 지각된 품질에 미치는 영향력은 PB가 NB보다 높게 나타난 반면 브랜드명성과 브랜드친숙도가 지각된 품질에 미치는 영향력은 NB가 PB보다 높게 나타났다. 이러한 실증분석 결과는 지각된 품질에 영향을 미치는 선행요인과 결과요인에 대한 보다 명확한 이해를 바탕으로 실무자가 마케팅 활동을 하는데 유용하게 활용할 수 있을 것이다.