• 소성∙가공
• /
• 제24권4호
• /
• pp.272-279
• /
• 2015

The characteristics of the laser metal deposition parameters were studied to enhance the deposition efficiency using a diode pumped disk laser. STD61 hot tool steel plate and Fe based AISI M2 alloy were used as a substrate and powder for the laser metal deposition, respectively. Among the laser metal deposition parameters the laser power, track pitch and powder feed rate were used to estimate the deposition efficiency. From the experimental results, the deposition efficiency was shown to be excellent when 1.8kW laser power 500um track pitch and 10g/min of the powder feed rate were used. For this optimal condition the average hardness of the deposition track was approximately 830HV, and this value is 30~50% better than the hardness of the commercially produced tool steel after heat treatment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1993년도 추계학술대회 논문집
• /
• pp.120-123
• /
• 1993

This paper describes the deposition and characteristics of electrochromic tungsten oxide thin films for electrochromic smart windows. Tungsten Oxide thin films(WO$_3$) are deposited by thermal evaporation techniques. By varying deposition parameters, WO$_3$ thin films exhibit different optical properties. The electrochromic devices are consist of ITO glass/ WO$_3$ thin films/ LiClO$_4$-propylene carbonate electrolyte/ counter electrode. The electrochromic properties of tungsten oxide thin films with different deposition condition ale investigated.

• 한국태양에너지학회 논문집
• /
• 제33권2호
• /
• pp.11-17
• /
• 2013

Silicon nitride($SiN_x:H$) deposited by radio frequency plasma enhanced chemical vapor deposition(RF-PECVD) is commonly used for anti-reflection coating and passivation in crystalline silicon solar cell fabrication. In this paper, characteristics of the deposited silicon nitride was studied with change of working pressure, deposition temperature, gas ratio of $NH_3$ and $SiH_4$, and RF power during deposition. The deposition rate, refractive index and effective lifetime were analyzed. The (100) p-type silicon wafers with one-side polished, $660-690{\mu}m$, and resistivity $1-10{\Omega}{\cdot}cm$ were used. As a result, when the working pressure increased, the deposition rate of SiNx was increased while the effective life time for the $SiN_x$-deposited wafer was decreased. The result regarding deposition temperature, gas ratio and RF power changes would be explained in detail below. In this paper, the optimized condition in silicon nitride deposition for silicon solar cell was obtained as 1.0 Torr for the working pressure, $400^{\circ}C$ for deposition temperature, 500 W for RF power and 0.88 for $NH_3/SiH_4$ gas ratio. The silicon nitride layer deposited in this condition showed the effective life time of > $1400{\mu}s$ and the surface recombination rate of 25 cm/s. The crystalline silicon solar cell fabricated with this SiNx coating showed 18.1% conversion efficiency.

• Corrosion Science and Technology
• /
• 제13권4호
• /
• pp.145-151
• /
• 2014

The objectives of this study are to investigate the effect of the concentration ratios of Ni and Fe ions on crud deposition onto the fuel cladding surface in the simulated primary environments of a pressurized water reactor. Crud deposition tests were conducted in the Ni and Fe concentration ratios of 20:20 ppm, 39:1 ppm and 1:39 ppm at $325^{\circ}C$ for 14 days. In the case of the same Ni and Fe ion ratio (20:20), nickel ferrite with a polyhedral shape was formed. Nickel oxide deposits with a needle shape were formed in the condition of high Ni to Fe ion ratio (39:1), While polyhedral iron oxide and needle-like nickel oxide formed in the condition of low Ni to Fe ion ratio (1:39). The amount of deposits increased, when Fe oxides were formed. This indicates that Fe rich oxides stimulated Ni oxide deposition.

• 대한기계학회논문집
• /
• 제18권5호
• /
• pp.1301-1309
• /
• 1994

A study of heat transfer and thermophoretic particle deposition has been carried out for the Modified Chemical Vapor Deposition(MCVD) process. A new concept utilizing two torches is suggested to simulate the heating effects from repeated traversing torches. Calculation results for the wall temperatures and deposition efficiency are in good agreement with experimental data. The effects of variable properties are included and heat flux boundary condition is used to simulate the moving torch heating. A conjugate heat transfer which includes heat conduction through solid layer and heat teansfer in a gas in a tube is analyzed. Of particular interests are the effects of torch speeds and solid layer thicknesses on the deposition efficiency, rate and the tapered entry length.

• 한국전기전자재료학회논문지
• /
• 제27권10호
• /
• pp.642-647
• /
• 2014

For feasible study of opto-electrical application regarding to oxide semiconductor, we implemented the N doped ZnO growth using a atomic layer deposition technique. The p-type ZnO deposition, necessary for ZnO-based optoelectronics, has considered to be very difficulty due to sufficiently deep acceptor location and self-compensating process on doping. Various sources of N such as $N_2$, $NH_3$, NO, and $NO_2$ and deposition techniques have been used to fabricate p-type ZnO. Hall measurement showed that p-type ZnO was prepared in condition with low deposition temperature and dopant concentration. From the evaluation of photoluminescence spectroscopy, we could observe defect formation formed by N dopant. In this paper, we exhibited the electrical and optical properties of N-doped ZnO thin films grown by atomic layer deposition with $NH_3OH$ doping source.

• 한국재료학회지
• /
• 제9권2호
• /
• pp.144-148
• /
• 1999

We have studied the deposition characteristics of thick silicon dioxide film on Si substrate by $O_3$/TEOS APCVD(Atmospheric Pressure Chemical Vapor Deposition). The effect of deposition parameters such as the distance between showerhead and substrate, deposition temperature, TEOS flow rate and $O_3$/TEOS ratio on deposition rate, surface morphology, and properties of films as investigated. As deposition temperature increased, deposition rate decreased but the surface morphology and adhesion of film to substrate improved. As the distance between showerhead and substrate decreased, the deposition rate increased. Etching rate using the BOE increased as TEOS flow rate increased, but was independent of$ O_3$/TEOS ratio. Deposition rate of $5\mu\textrm{m}$/hour was obtained under the condition that the distance between showerhead and substrate was 5mm and the deposition temperature was $370^{\circ}C$.

• 열처리공학회지
• /
• 제29권2호
• /
• pp.62-65
• /
• 2016

TIO thin films were deposited on the poly-carbonate substrates with RF magnetron sputtering under different sputtering power condition to investigate the influence of deposition rate on the electrical and optical properties of the films. Although, all films have the similar carrier concentration, the films prepared at a lower deposition rate of 4 nm/min show a higher mobility of $5.96cm^2\;V^{-1}S^{-1}$ due to the low surface roughness. In addition, optical transmittance is also influenced by a deposition rate. Based on the figure of merit, it can be concluded that the lower deposition rate effectively enhances the opto-electrical performance of IGZO films for use as transparent conducting oxides in flexible display applications.

• 한국결정학회지
• /
• 제3권1호
• /
• pp.53-66
• /
• 1992

Extensive research has been perform성 on the property-microstructure-process condition relations of thin films. The various proposed models are mainly based on physical vapor deposition processes. Especially the study on the surface condition of substrates in Zone 1 with low surface mobility has not been sufficient. In this study, therefore, we discussed the mochological changes of TiN films deposited by plusma enhanced chemical vapor deposition process with substrates of different composition and micro-rorghness, and compared it with the Structure Zone Model. We could find out that the growth rate of films increased and micro-grain size decreased with the increase in micro-roughness, but it does not improve the mechanical properties because of many imperfections like voids, micro-cracks, stacking faults, etc. This means that, in these deposition conditions, the increase in shadowing diffect is more effective than the increase in nucleation sites on the growth of films due to the increase in substrate roughness.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.391-394
• /
• 2002

Transparent conductive oxides (TCO) are necessary as front electrode for most thin film solar cell. In our paper, transparent conducting aluminum-doped Zinc oxide films (ZnO:Al) were prepared by rf magnetron sputtering on glass (Corning 1737) substrate as a variation of the deposition condition. After deposition, the smooth ZnO:Al films were etched in diluted HCl (0.5%) to examine the electrical and surface morphology Properties as a variation of the time. The most important deposition condition of surface-textured ZnO films by chemical etching is the processing pressure and the substrate temperature. In low pressures (0.9 mTorr) and high substrate temperatures ($\leq$30$0^{\circ}C$), the surface morphology of films exhibits a more dense and compact film structure with effective light-trapping to apply the silicon thin film solar cells.