• International Journal of Highway Engineering
• /
• v.9 no.4
• /
• pp.33-43
• /
• 2007

Because usually signal controllers on the crosswalks of mid-block provide pedestrian signals every cycle based on the fixed signal plan, pedestrian signals are provided even when there is no pedestrian demand. Consequently, signal is operated inefficiently and this may cause drivels to experience useless delay or violate the signal. Even though recently pushbuttons have been installed to improve the efficiency of pedestrian signal control in the crosswalks of mid-block and the pedestrian safety. they are not spread out national-wide in Korea because of the cost of the pushbutton equipments and the lack of an acknowledgement of the efficiency of the pushbutton. In this study, the effectiveness of the pushbutton on saving the vehicle delay was verified through before and after study in 4 study sites using a traffic micro-simulation model, VISSIM. To evaluate the viability of the pushbutton, a benefit/cost analysis was also performed for 4 study sites. It was found that B/C ratio of all of 4 study sites was greater than 1. The sensitivity analysis for the traffic volume and pedestrian volume were performed to identify the impact of the both volume on the operation of pushbutton. And, a benefit/cost analysis was performed for all scenarios. It was found that when the pedestrian volume is greater than 90ped/h, the pedestrian signal was operated same as the fixed signal plan. That is, there is no benefit of pushbutton at all once the pedestrian volume is greater than 90ped/h. When the pedestrian volume is equal to or less than 90ped/h and the traffic volume is greater than 2,500veh/h, B/C ratio is greater than 1. Also it was found that as traffic volume increases and pedestrian volume decreases, the benefit increases. In this study, the criteria for installation of pushbutton on the crosswalks of mid-block are developed through the sensitivity analysis and benefit/cost analysis. The results of this study may be used as a criteria for expansion of pushbutton system.

• Korean Security Journal
• /
• no.29
• /
• pp.163-191
• /
• 2011

Recently, the problems in school violence did not stop on the crime between the members at the school and which developed into the invasion crime of the school caused by outsiders. The school is no more the safety zone from the crime. Particularly, in the case of the elementary school, because there are nearly no people who oppose to the outside attacker and can control this, it is the place where it is vulnerable to the invasion crime. The Metropolis of Seoul implements the School Sheriff system within the jurisdiction bureau, in the public elementary school. However, actually the School Sheriff business is being managed, never applying a rule in the Security Industry Law with the main content, that is the Security Industry Law application is excluded. Because the jurisdiction on the contract of Seoul City and operating company are run, the various issues is caused. First, since it is not being considered as a security business, the commercial liability insurance for security company has no chance to applicate when the operation company and the School Sheriff have related damage generation. So the security for the indemnification of loss of the victim is weak. Second, The task of the School Sheriff is ruled just by in the individual contracts. But it is insufficient with this thing. The related duties are required some supplement like a general rule application including the obligation of the guard in the security industry law. Third, the education of the School Sheriff needs to connect with the educational programme in the security industry law. The related professional education specially needed for the prevention of school violence ought to be reserved compensation. Forth, the citizens still demand the strengthening of police patrol for the surroundings of a school in spite of the result of Seoul City's public survey. Therefore, the active relation of cooperation with the police needs to be supported legally and institutionally with the Security Industry Law application. Fifthly, the success of the School Sheriff business can be more guaranteed with the supervision of the legal and institutional device like a the Security Industry Law application or police and all sorts of administrative execution's and etc.

• Korean journal of food and cookery science
• /
• v.28 no.4
• /
• pp.413-421
• /
• 2012

This study was conducted with 418 adults 20 years or older, all of whom lived in Daegu and Gyeongbuk. According to a survey, the number of females was greater than that of males (40.7%) by 59.3%, and that for ages 30 years was the highest. The preference for Korean traditional drinks was relatively high at 51.8%, and the frequency of drinking Korean traditional drinks was 39.0%. The adults answered that they had these beverages on special days such as holidays, ritual days, and birthdays. Among the reasons for drinking a traditional beverage 'good taste' scored the highest with 27.0% of respondents, followed by 'Korean traditional food' with 24.4%. The recognition of Korean traditional drinks was high in the order of Sikhe, Soojunggwa, Cha, and Hwachae. The preference for Sikhe was the highest. The group who agreed that it was important to develop a Korean functional traditional drink was 11.5% higher than that of the negative group, as 13.4% 'agreed a lot' and 41.1% 'agreed'. Consumer awareness toward traditional drink functionality was generally positive, with 3.5 points or higher on average, and awareness of the nutritional supplementation, diabetes control, the recuperative effects of the drinks were also high. Among Korean traditional drinks Sikhe was the highest with regard to intention to purchase. As a result, the popularization of traditional Korean drinks was based on three factors: quality oriented image, popularity oriented image, and product attribute-oriented image. These factors significantly influenced the preference for and purchase of Korean functional traditional drinks.

• Journal of Distribution Science
• /
• v.9 no.3
• /
• pp.83-94
• /
• 2011

Most domestic companies, with the exclusion of major firms, are reluctant to implement a supply chain management (SCM) network into their operations. Most small- and medium-sized enterprises are not even aware of SCM. Due to the inherent total-systems efficiency of SCM, it coordinates domestic manufacturers, subcontractors, distributors, and physical distributors and cuts down on cost of inventory control, as well as demand management. Furthermore, a lack of SCM causes a decrease in competitiveness for domestic companies. The reason lies in the fundamentality of SCM, which is the characteristic of information sharing, process innovation throughout SCM, and the vast range of problems the SCM management tool is able to address. This study suggests the contemplation and reformation of the current SCM situation by analyzing the SCM strategic plan, discourses and logical discussions on the topic, and a successful case for adapting SCM; hence, the study plans to productively "process" SCM. First, it is necessary to contemplate the theoretical background of SCM before discussing how to successfully process SCM. I will describe the concept and background of SCM in Chapter 2, with a definition of SCM, types of SCM promotional activities, fields of SCM, necessity of applying SCM, and the effects of SCM. All of the defects in currently processing SCM will be introduced in Chapter 3. Discussion items include the following: the Bullwhip Effect; the breakdown in supply chain and sales networks due to e-business; the issue that even though the key to a successful SCM is cooperation between the production and distribution company, during the process of SCM, the companies, many times, put their profits first, resulting in a possible defect in demands estimation. Furthermore, the problems of processing SCM in a domestic distribution-production company concern Information Technology; for example, the new system introduced to the company is not compatible with the pre-existing document architecture. Second, for effective management, distribution and production companies should cooperate and enhance their partnership in the aspect of the corporation; however, in reality, this seldom occurs. Third, in the aspect of the work process, introducing SCM could provoke corporations during the integration of the distribution-production process. Fourth, to increase the achievement of the SCM strategy process, they need to set up a cross-functional team; however, many times, business partners lack the cooperation and business-information sharing tools necessary to effect the transition to SCM. Chapter 4 will address an SCM strategic plan and a case study of LG Electronics. The purpose of the strategic plan, strategic plans for types of business, adopting SCM in a distribution company, and the global supply chain process of LG Electronics will be introduced. The conclusion of the study is located in Chapter 5, which addresses the issue of the fierce competition that companies currently face in the global market environment and their increased investment in SCM, in order to better cope with short product life cycle and high customer expectations. The SCM management system has evolved through the adaptation of improved information, communication, and transportation technologies; now, it demands the utilization of various strategic resources. The introduction of SCM provides benefits to the management of a network of interconnected businesses by securing customer loyalty with cost and time savings, derived through the consolidation of many distribution systems; additionally, SCM helps enterprises form a wide range of marketing strategies. Thus, we could conclude that not only the distributors but all types of businesses should adopt the systems approach to supply chain strategies. SCM deals with the basic stream of distribution and increases the value of a company by replacing physical distribution with information. By the company obtaining and sharing ready information, it is able to create customer satisfaction at the end point of delivery to the consumer.

• Korean Journal of Soil Science and Fertilizer
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2001

Total upland area for cultivating the vegetable crops in the Alpine soils of Northeastern South Korea has been extending its limit to meet the increasing demand of vegetable food in recent decades. About 70% of these alpine soils are located in over 7% of the slope and most of vegetable crops have been cultivated intensively without practicing the best management systems. Thus, soil erosion and continuous cropping system have degenerated the soil fertility and shown detrimental effects on water quality. We initiated an intensive and extensive investigation to characterize the fertility problems encountered in these uplands. Objectives of this paper were to characterize the fertility status in the Alpine soils cultivated with vegetable crops for many years and to provide the recommendations for adequate soil management measures including fertilization and erosion control. Soils in general have good drainage with textural classes of loam or sandy loam. Their topographical characteristics tended to lead them to shallow plow layers, and the steepness of the terrain created erosion hazard. Of the soils examined, about 11% of uplands over 30% gradient was found in need of an urgent reforestation. A high content of gravel and firm hardness of soil attributed to inhibit the utilization of farm machinery and plant-root development. The average soil pH 5.6 was slightly low relative to pH 5.70 of the national average. Organic matter content was high compared with 2.0% of national average, but decreased with the prolonged cultivation periods. Available $P_2O_5$ concentration was unusually high due to the consequence of over dose application with chemical and organic fertilizers. Exchangeable cations as Ca, Mg, and K were appeared to be decreased in these regions with prolonging the cultivation periods. There were no significant differences in cation exchange capacity (CEC) and electrical conductivity (EC) among locations. Heavy metal contents were mostly lower than the threshold of danger level designated by Soil Environment Conservation Law of South Korea. Results indicated that a proper countermeasure and the best management practice should be immediately implemented to conserve the top soil and fertility in the Alpine regions.

• The Korean Journal of Archival Studies
• /
• no.20
• /
• pp.151-212
• /
• 2009

Museums are producing new value and being redefined as places that reproduce context, as the process of globalization are being reflected in museum activities. The new additional functions and roles to the traditional mission of museums allow artworks to find potential functions of art archive and meseum. At the same time, the public has faced originality and aura of an artwork by viewing the physical subject. However, with the appearance of a new digital object, the initiative of viewing has moved over from the artwork to the hands of the public. Now, the public does not go to the museum to see an artwork, but has started to adopt to an opposite paradigm of bringing the artwork forward to the screen. Therefore, they are not satisfied any longer with just seeing an artwork, but demand more information about the artworks and reproduce it as knowledge. Therefore, this study aimed to find types and characteristics through definition and range selection of art archive at this point where the value of art archive is enhanced and systematic management is required, and to present record management methods according to art archive structure and core execution function. It especially stressed that the basis of overall art archive definition was in an 'approach' paradigm rather than a 'preservation' paradigm, and embodied various application methods of digitalized art records. The digital object of an artwork was recognized as the first materialization of an actual artwork, and the digital original of an artwork was presented as the core record. Art archive managed under physical and intellectual control were organically restructured focusing on digital original copies of artworks, which are the core record in a digital technology environment, and could be provided to users in forms of various services that meet their demands. The beginning of systematic management of such art records will become a first step to enhance historical value, establish art cultural identity, and truly possess art culture.

• Food Science and Industry
• /
• v.55 no.2
• /
• pp.188-202
• /
• 2022

In the insect industry, as the scope of application of insects is expanded from pet insects and natural enemies to feed, edible and medicinal insects, the demand for quality control of insect raw materials is increasing, and interest in securing the safety of insect products is increasing. In the process of expanding the industrial scale, controlling the temperature and humidity and air quality in the insect breeding room and preventing the spread of pathogens and other pollutants are important success factors. It requires a controlled environment under the operating system. European commercial insect breeding facilities have attracted considerable investor interest, and insect companies are building large-scale production facilities, which became possible after the EU approved the use of insect protein as feedstock for fish farming in July 2017. Other fields, such as food and medicine, have also accelerated the application of cutting-edge technology. In the future, the global insect industry will purchase eggs or small larvae from suppliers and a system that focuses on the larval fattening, i.e., production raw material, until the insects mature, and a system that handles the entire production process from egg laying, harvesting, and initial pre-treatment of larvae., increasingly subdivided into large-scale production systems that cover all stages of insect larvae production and further processing steps such as milling, fat removal and protein or fat fractionation. In Korea, research and development of insect smart factory farms using artificial intelligence and ICT is accelerating, so insects can be used as carbon-free materials in secondary industries such as natural plastics or natural molding materials as well as existing feed and food. A Korean-style customized breeding system for shortening the breeding period or enhancing functionality is expected to be developed soon.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.67 no.4
• /
• pp.234-241
• /
• 2022

Wheat (Triticum aestivum L.) is a major staple foods and is in increasing demand in the world. The elevated temperature caused by changes in climate and environmental conditions is a major factor affecting wheat development and grain quality. The optimal temperature range for winter wheat is between 15 and 25℃, and it is necessary to study the physiological characteristic of wheat according to elevated temperatures. This study presents the effect of elevated temperature on the yield and quality of two Korean bread wheat (Baekkang and Jokyoung) in temperature gradient tunnels (TGT). Two bread wheat cultivars were grown in TGT at four different temperature conditions: T0 (control, near ambient temperature), T1 (T0+1℃), T2 (T0+2℃), (T0+2℃), T3 (T0+3℃). The period from sowing to heading stage accelerated and the number of grains per spike and grain yield reduced under T3 condition compared with those under T0 condition. Grain filling rate and grain maturity also accelerated with elevated temperature (T3). The increase in temperature led to the increase in protein contents, whereas decreased the total starch contents. These results are consistent with the decreased expression of starch synthesis genes and increased gliadin synthesis or gluten metabolism genes during the late grain filling stage. Taken together, our results suggest that the increase in temperature (T3) led to the decrease in grain yield by regulating the number of grains/spike, whereas increased the protein content by regulating the expression of starch and gliadin-related genes or gluten metabolism process genes expression. In addition, our results provide a useful physiological information on the response of wheat to heat stress.

• Tunnel and Underground Space
• /
• v.33 no.4
• /
• pp.281-298
• /
• 2023

Continuous research efforts are being devoted to unmanned mobile platforms for lunar exploration. There is an ongoing demand for real-time information processing to accurately determine the positioning and mapping of areas of interest on the lunar surface. To apply deep learning processing and analysis techniques to practical rovers, research on software integration and optimization is imperative. In this study, a foundational investigation has been conducted on real-time analysis of virtual lunar base construction site images, aimed at automatically quantifying spatial information of key objects. This study involved transitioning from an existing region-based object recognition algorithm to a boundary box-based algorithm, thus enhancing object recognition accuracy and inference speed. To facilitate extensive data-based object matching training, the Batch Hard Triplet Mining technique was introduced, and research was conducted to optimize both training and inference processes. Furthermore, an improved software system for object recognition and identical object matching was integrated, accompanied by the development of visualization software for the automatic matching of identical objects within input images. Leveraging satellite simulative captured video data for training objects and moving object-captured video data for inference, training and inference for identical object matching were successfully executed. The outcomes of this research suggest the feasibility of implementing 3D spatial information based on continuous-capture video data of mobile platforms and utilizing it for positioning objects within regions of interest. As a result, these findings are expected to contribute to the integration of an automated on-site system for video-based construction monitoring and control of significant target objects within future lunar base construction sites.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.49 no.3
• /
• pp.247-258
• /
• 2023

This study aims to investigate the enhancement of water resistance and improvement in adhesion to the skin by combining dextrin palmitate and isopropyl titanium triisostearate coating materials with titanium dioxide. Due to the recent increase in consumers who enjoy outdoor activities, the demand for sunscreen with excellent water resistance is increasing. Prior research was conducted with O/W, Pickering, and W/O/W multiple formulations, but there was a limit to water resistance. The purpose of this study is to develop a complex inorganic powder that can improve water resistance and increase adhesion to the skin to solve this problem. First, we combined dextrin palmitate and isopropyl titanium triisostearate coating materials to form a composite with titanium dioxide. The coating of the inorganic powder was confirmed using FE-SEM and FT-IR analysis. The composite exhibited significantly higher in vitro water resistance compared to other formulations. The hydrophobicity of the coated inorganic powder was compared by measuring the contact angles. When the coated inorganic powder was applied to the W/O sunscreen formulation and the non-coated inorganic powder was applied to the W/O sunscreen formulation as a control, the SPF of the sunscreen containing the coated inorganic powder was higher. These results were the same when observed with a UV camera. Finally the adhesion of the coated inorganic powder to the skin was assessed by applying it to a foundation product. In vivo study, it was observed that the product formulated with the coated powder exhibited less smudging compared to the foundation product formulated with the non-coated powder. The developed inorganic powder in this study demonstrated excellent adhesion to the skin, providing a superior sensory experience, as well as enhanced hydrophobicity and remarkable water resistance effects. In the future, the result of this study is expected to help develop various sunscreen products to improve water resistance.