• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.6 no.11
• /
• pp.2992-3007
• /
• 2012

Recently there has been an increasing interest in exploring the radio irregularity research problem in Wireless Sensor Networks (WSNs). Measurements on real test-beds provide insights and fundamental information for a radio irregularity model. In our previous work "LMAT", we solved the path planning problem of the mobile anchor node without taking into account the radio irregularity model. This paper further studies how the localization performance is affected by radio irregularity. There is high probability that unknown nodes cannot receive sufficient location messages under the radio irregularity model. Therefore, we dynamically adjust the anchor node's radio range to guarantee that all the unknown nodes can receive sufficient localization information. In order to improve localization accuracy, we propose a new 2-hop localization scheme. Furthermore, we point out the relationship between degree of irregularity (DOI) and communication distance, and the impact of radio irregularity on message receiving probability. Finally, simulations show that, compared with 1-hop localization scheme, the 2-hop localization scheme with the radio irregularity model reduces the average localization error by about 20.51%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.11
• /
• pp.1014-1021
• /
• 1998

We evaluated the effect of processing variables on microstructural evolution interface irregularity between Ag sheath and superconductor core and resultant critical current density(J$_{c}$) of (Bi,Pb)$_2$Sr$_2$Ca$_2$Cu$_3$O$_{x}$(2223) superconductor tape. The value of J$_{c}$ was significantly influenced by the interface irregularity, degree of texturing and relative 2223 content. The interface became more irregular(sausage effect), while the degree of texturing gradually improved as the dimension of tape decreased during forming process. As the dimension of wire/tape were changed from diameter of 3.25 mm to thickness of 0.20 mm, J$_{c}$ value was observed to be increased by 10 times. In addition, optimum sintering temperature for improved J$_{c}$ was observed to be 835$^{\circ}C$ in a ambient atmosphere probably due to combined effect of both improved texturing and high 2223 content. Microstructural investigation showed the degree of texturing was degraded by the existence of both second phases and interface irregularity. It was observed that larger grain size and better texturing was developed near relatively flat interface compared to those inside superconducting core.ting core.

• Earthquakes and Structures
• /
• v.26 no.5
• /
• pp.349-361
• /
• 2024

Excessive torsional behaviour is one of the major reasons for failure of buildings, as inferred from past earthquakes. Numerous seismic codes across the world specify a displacement-based or drift-based criterion for classifying buildings as torsionally irregular. In recent years, quite a few researchers have pointed out some of the inherent deficiencies associated with the current codal guidelines on torsional irregularity. This short communication paper aims to envisage the need for a revision of the displacement-based guidelines on torsional irregularity, and further highlight the appropriateness of a rotation-based criterion. A set of 6 reinforced concrete building models with asymmetric shear walls are analysed using ETABS v18.0.2, by varying the number of stories from 1 to 9, and the torsional irregularity coefficient of various stories is calculated using the displacement-based formula. Since rotation about the vertical axis is a direct indication of the twist experienced by a building, the calculated torsional irregularity coefficients of all stories are compared with the corresponding floor rotations. The conflicting results obtained for the torsional irregularity coefficients are projected through five categories, namely mismatch with floor rotations, inconsistency in trend, lack of clarity in incorporation of negative values, sensitivity to low values of displacement and error conceived in the mathematical formulation. The findings indicate that the irregularity coefficient does not accurately represent the torsional behaviour of buildings in a realistic sense. The Indian seismic code-based values of 1.2 and 1.4, which are used to characterize buildings as torsionally irregular are observed to be highly sensitive to the numerical values of displacements, rather than the actual degree of rotation. The study thus emphasizes the revision of current guidelines based on a more relevant rotation-based or eccentricity-based approach.

• The korean journal of orthodontics
• /
• v.46 no.1
• /
• pp.3-12
• /
• 2016

Objective: The purpose of this study was to compare the precision of three-dimensional (3D) images acquired using iTero$^{(R)}$(Align Technology Inc., San Jose, CA, USA) and Trios$^{(R)}$(3Shape Dental Systems, Copenhagen, Denmark) digital intraoral scanners, and to evaluate the effects of the severity of tooth irregularities and scanning sequence on precision. Methods: Dental arch models were fabricated with differing degrees of tooth irregularity and divided into 2 groups based on scanning sequence. To assess their precision, images were superimposed and an optimized superimposition algorithm was employed to measure any 3D deviation. The t-test, paired t-test, and one-way ANOVA were performed (p < 0.05) for statistical analysis. Results: The iTero$^{(R)}$ and Trios$^{(R)}$ systems showed no statistically significant difference in precision among models with differing degrees of tooth irregularity. However, there were statistically significant differences in the precision of the 2 scanners when the starting points of scanning were different. The iTero$^{(R)}$ scanner (mean deviation, $29.84{\pm}12.08{\mu}m$) proved to be less precise than the Trios$^{(R)}$ scanner ($22.17{\pm}4.47{\mu}m$). Conclusions: The precision of 3D images differed according to the degree of tooth irregularity, scanning sequence, and scanner type. However, from a clinical standpoint, both scanners were highly accurate regardless of the degree of tooth irregularity.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1996.10a
• /
• pp.319-322
• /
• 1996

Automatic gauge control algorithm in rolling process is composed of several functions. Among them feedforward control method is used to compensate irregularity of input strip thickness before rolling process. Since it's very difficult to get an explicit relation between the degree of irregularity of input strip and manipulated variables, approximate linear equation like straight line is used in real system. Furthermore parameters included in such static equation should be changed by characteristics of input strip and modified by roll states. Despite this problem, rolling process use variables in feedfroward controller as a constant. Therefore this problem increases the possibilities of irregularity of thickness control. This paper presents an algorithm which can properly infer present states of process and intelligently manipulate the parameter of feedforward controller.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.9
• /
• pp.1060-1068
• /
• 2016

The range-free localization using connectivity information has problems of mobile tracking. This paper proposes two Bayesian filter-based mobile tracking algorithms considering a propagation scenario. Kalman and Markov Chain Monte Carlo (MCMC) particle filters are applied according to linearity of two measurement models. Measurement models of the Kalman and MCMC particle filter-based algorithms respectively are defined as connectivity between mobiles, information fusion of connectivity information and received signal strength (RSS) from neighbors within one-hop. To perform the accurate simulation, we consider a real indoor map of shopping mall and degree of radio irregularity (DOI) model. According to obstacles between mobiles, we assume two types of DOIs. We show the superiority of the proposed algorithm over existing range-free algorithms through MATLAB simulations.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.4
• /
• pp.204-211
• /
• 2011

A dynamic analysis procedure is developed to provide a better estimation of the dynamic responses of bridge during the passage of high speed railway vehicles. Particularly, a three dimensional numerical model including the structural interaction between high speed vehicles, bridges and railway endures to analyse accurately and evaluate with in-depth parametric studies for dynamic responses of various bridge span lengths running KTX railway locomotive up to increasing maximum speed(450km/h). Three dimensional frame element is used to model the simply supported pre-stressed concrete (PSC) box bridges for four span lengths(40~25m). Track irregularity employed as a stationary random process from the given spectral density functions and irregularities of both sides of the track are assumed to have high correlation. The high-speed railway vehicle (KTX) is used as 38-degree of freedom system. Three displacements (Vertical, lateral, and longitudinal) as well as three rotational components (Pitching, rolling, and yawing) are considered in the 38-degree of freedom model. The dynamic amplification factors are evaluated by the developed procedure under various traveling conditions, such as track irregularity camber, train speed and ballast. The dynamic analysis such as Newmark-${\beta}$ and Runge-Kutta methods which are able to analyse considering the dynamic impact factors are compared and contrasted.

• Restorative Dentistry and Endodontics
• /
• v.17 no.1
• /
• pp.153-165
• /
• 1992

Dental composite resin is a kind of the particle - reinforced composite material, and is widely used in recent dental restoration of anterior and posterior tooth region. The purpose of this study was to investigate the fracture behaviour according to volume fractions and external findings of the filler particles for better interpretation of the fracture characteristics of posterior dental composite resins by analytic method of fracture mechanics. The plane strain fracture toughness($K_{IC}$) and Acoustic Emission were determined with three - point bending test using the single edge notch specimen according to the ASTM - E399, and its analyzed data was compared with filler volume fractions derived from the standard ashing test and scanning electron fractographs of each specimen including the unfilled experimental resin as a control. The results were that the value of fracture toughness of the composite resin material was in the range from 0.85 MPa$\sqrt{m}$ to 1.60 MPa$\sqrt{m}$ and was higher than the value of the unfilled experimental resin, and the fracture behaviours dervied from Acoustic Emission analysis show prominent differences according to the volume fraction and the size of filler particles used in each composite resin. The degree of resistance against crack propagation seems to be increase and the fractographs demonstrate the high degree of surface roughness and irregularity according with the increase of fracture toughness value.

• Women's Health Nursing
• /
• v.4 no.3
• /
• pp.402-415
• /
• 1998

The purpose of study was to identify the degree of menopausal of age knowledge and management of menopausal women. The data were collected from April 1st to May 31th in 1998 and 368 total. Data were analyzed by SPSS/PC program. The results were as follows. 1. The average age was 45-50 years. General health state was good 71% mosty they were house keeper. 87.5% had religion. The married woman was 86.1%. Menopause treatment experience was 88.1%. The educational state was below middle school, 72.3%. 2. The high score of knowledge of menopause was the item of whether they conceive or not after menopause, irregularity of menopause, menopausal symptoms, of the possibility osteoporosis. 3. The score of knowledge was the highest at the group 45-50, the high education, and the high number of family members. 4. The score of management was the highest in self control category. No drinking & no smoking items were the highest. Sexual management and management by professional person were low score. 5. The higher score of the knowledge of menopause, the higher score of the management.

• Imaging Science in Dentistry
• /
• v.51 no.2
• /
• pp.155-165
• /
• 2021

Purpose: This study aimed to evaluate changes of the alveolar bone and interdental bone septum of the mandibular incisors through cone-beam computed tomography (CBCT) after orthodontic treatment of mandibular dental crowding without dental extraction. Materials and Methods: The sample consisted of 64 CBCT images(32 pre-treatment and 32 post-treatment) from 32 adult patients with class I malocclusion and an average age of 23.0±3.9 years. The width and height of the alveolar bone and interdental septum, the distance between the cementoenamel junction (CEJ) and the facial and lingual bone crests, and the inclination of the mandibular incisors were measured. Results: The distance between the CEJ and the marginal bone crest on the facial side increased significantly (P<0.05). An increased distance between the CEJ and the bone crest on the facial and lingual sides showed a correlation with the irregularity index (P<0.05); however, no significant association was observed with increasing mandibular incisor inclination (P>0.05). The change in the distance between the CEJ and the marginal bone crest on the facial side was correlated significantly with bone septum height(P<0.05). Conclusion: Bone dehiscence developed during the treatment of crowding without extraction only on the incisors' facial side. Increasing proclination of the mandibular incisor was not correlated with bone dehiscence. The degree of dental crowding assessed through the irregularity index was associated with the risk of developing bone dehiscence. The interdental septum reflected facial marginal bone loss in the mandibular incisors.