• Journal of Sericultural and Entomological Science
• /
• v.14 no.2
• /
• pp.105-112
• /
• 1972

The effects of the stretching speed and the swelling degree of cocoon filaments on load-elongation curve were tested by tensilon with special attachments. The values of breaking strength, elongation at break and initial tensile strength obtained from load elongation curves are summarized as follows; 1. The breaking strength of the swollen cocoon filament appeared to increase at the high stretching speed, while elongation at break decreased. 2. Load-elongation curve became crinkled at the low speed of stretching. It suggests that both slip and break of the macrofibrils may occur in swelling of cocoon bave. 3. Breaking strength appeared to considerably decrease and elongation at break not to increase in swelling test at 9$0^{\circ}C$ for 60 min. 4. The initial tensile strength was influenced by the stretching speed and swelling degree of cocoon filaments.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1425-1427
• /
• 2002

Degree of crosslinking of insulation is very important factor that is determined characteristics of XLPE insulated power cable. Increase of degree of crosslinking is closely related to increase of mechanical characteristics of XLPE insulated power cable. In this study, mechanical characteristics of XLPE insulation for degree of crosslinking was analyzed tensile strength and elongation of insulation. As the result, mechanical characteristics of insulation for degree of crosslinking was divided three cases.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.4
• /
• pp.395-398
• /
• 1999

Chitin was isolated from red snow crab (Chinonecetes japonicus) and deacetylated by boiling alkaline solution to produce chitosan. The physical properties of chitosan solution and its film properties was examined, As the molecular weights of chitosan was increased from 297Kpa to 319Kpa, the tensile strength, degree of elongation and water permeability of chitosan film were increased. As the degree of deacetylation of chitosan was increased, the tensile strength, the degree of elongation and water permeability of chitosan film were increased. As the concentration of chitosan solution was increased, the degree of elongation and water permeability of film were increased, whereas the tensile strength of film was decreased, As the pH of chitosan solution was increased, the tensile strength and water permeability of film were decreased, whereas the degree of elongation of film was increased.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.1-5
• /
• 2014

This study is experimentally investigated whether or not a relationship exists between the mechanical properties and damping capacity of cold-rolled 316 L stainless steel. Deformation-induced martensite was formed with surface relief and directionality. With the increasing degree of deformation, the volume fraction of ${\varepsilon}$-martensite increased, and then decreased, while ${\alpha}^{\prime}$-martensite increased rapidly. With an increasing degree of deformation, tensile strength was increased, and elongation was decreased; however, damping capacity was increased, and then decreased. Tensile strength and elongation were affected in the ${\alpha}^{\prime}$-martensite; hence, damping capacity was influenced greatly by ${\varepsilon}$-martensite. Thus, there was no proportional relationship between strength, elongation, and damping capacity.

• Textile Coloration and Finishing
• /
• v.9 no.4
• /
• pp.7-19
• /
• 1997

The purpose of the study was to investigate the shrinkage and creep behavior of PET filaments which were prepared at various spinning speeds(3,300, 4,000, 5,000, 6,000, and 7,000m/min) and anneal($120^{\circ}$, 30min & $150^{\circ}$, 40min). In order to determine the shrinkage and creep behavior with the crystallinity change, PET filaments were treated with low(12$0^{\circ}C$, 30min) and high($150^{\circ}$, 40min) temperature conditions with hot air dryer under the constant tension. The results of the study were as follows: as the spinning speed increased, the degree of shrinkage and elongation of the sample treated by wet condition decreased. The sample with 0.01g/d of load under various spinning speeds showed shrinkage behavior and highest shrinkage ratio at $76^{\circ}$ which was Tg of PET. The degree of shrinkage and elongation of the treated sample was less than those of the untreated sample by wet treatment. Especially, there was less degree of shrinkage and elongation of the sample treated by higher temperature condition. In 3,300m/min of spinning speed the draw ratio of undrawn yarn of a mixture of a-axis orientation and c-axis orientation was 2.0, which is similar to the value of the traditional drawn yarn. Finally, there was a big range of shrinkage and elongation by wet treatment in 3,300 m/min of spinning speed.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.45 no.1
• /
• pp.50-54
• /
• 2000

The elongation of mesocotyl and coleoptile plays important roles in the seedling emergence and stand establishment of dry direct-seeded rice. Experiments were carried out to elucidate the effects of seed-presoaking treatments of GA$_3$ and some inorganic salts on the mesocotyl, and coleoptile elongation of rice. Seed-soaked GA$_3$ promoted the elongation of mesocotyl, but little effect on the coleoptile elongation. The stimulation effects of GA$_3$ were found to be enhanced by addition of CaCl$_2$ However, the sole treatment of CaCl$_2$ showed no stimulating effect on the mesocotyl and coleoptile elongation. Mesocotyl elongation was most prominent in the combined treatments of 50ppm GA$_3$ with 100 mM CaCl$_2$. The synergistic effects of GA$_3$ and CaCl$_2$ on mesocotyl elongation varied with varietal groups. The stimulating effects of GA$_3$ were enhanced significantly by the addition of CaCl$_2$ in japonica varieties, Dongjinbyeo, Ilpumbyeo and Milyang 95, and tall indica variety, Labelle, but not in semidwarf Tongil type varieties, Tongilbyeo, Milyang 23, and Nampungbyeo, and semi-dwarf indica, Short Labelle. The promoting effects of GA$_3$ on the mesocotyl elongation were decreased in proportion to the lowered osmotic potential by PEG 6000 on the contrary to CaCl$_2$ This implies that the synergistic effects of CaCl$_2$ with GA$_3$ on mesocotyl elongation was not caused by osmotic potential lowered by CaCl$_2$ addition but by the salt itself. Salts such as Ca(NO$_3$)$_2$, MgCl$_2$ BaCl$_2$, NaCl, KCl and KNO$_3$ showed the synergistic effects with GA$_3$ on mesocotyl elongation as well. The degree of synergistic effects showed no differences among salts tested, implying that there is no specificity of ions constituting the salts.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.11 no.1
• /
• pp.63-69
• /
• 1987

Silk fibroin is likely to be hydrolyzed by acids or alkalies at high temperature, and the degree of the hydrolysis has been inferred from the changes in tensile strength and elongation. But, in this experiment, it was intended to infer that from the quantitative changes in terminal aminp group content as well as in tensile strength and elongation. Silk yarn was treated with boiling water, hydrochloric acid, and sodium hydroxide under various conditions. The boiling water somewhat degraded silk fibroin. Silk yarn treated with sodium hydroxide contained more terminal amino group than that treated with hydrochloric acid. This result agreed fairly well with the loss in weight, tensile strength, and elongation: the terminal amino group content increased with the decrease of tensile strength, elongation, and weight. The damage by sodium hydroxide to the silk fibroin was greater than that by hydrochloric acid.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.6
• /
• pp.327-335
• /
• 2004

Effect of spherodization of cementite on static and dynamic deformation behaviors of SCM415 steels was investigated in this study. Dynamic torsional test was conducted using torsional Kolsky bar with the strain rate of $1.6{\times}10^3/s$. Three type of specimens were used with different spherodization degree of cementite. Dynamic test results were analyzed comparing with static tensile results and microstructural changes. The obtained results are as follows; 1) All the specimens of static and dynamic tests showed a ductile fracture mode of dimple. Specimens of the dynamic test showed adiabatic shear bands on the beneath of fracture surface. 2) In static tensile test, decreased tensile strength and increased uniform and non-uniform elongations appeared as spherodization degree of cementite increased. 3) In dynamic torsional test, decreased shear strength and increased uniform elongation appeared as spherodization degree of cementite increased. 4) Due to the largest uniform elongation, superior cold forgeability at high speed is expected on high spherodization degree of cementite.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.3
• /
• pp.116-121
• /
• 2021

This study was carried out to investigate the effect of transformation induced martensite on the tensile properties of Fe-20Mn-12Cr-3Ni-3Si alloy. α' and ε-martensite were formed by cold rolling, and these martensite were formed with according to the specific direction, surface relief and partially intersection. With an increasing degree of cold rolling, amount of α'-martensite was slowly increased, whereas amount of ε-martensite was rapidly increased. Volume fraction of ε-martensite formed by cold working was large than α'-martensite. Tensile strength was rapidly increase and elongation was rapidly decreased with an increasing of degree of cold rolling. This means that tensile strengh and elongation was greatly influenced by the volume fraction of ε-martensite formed by cold rolling then α'-martensite.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.3
• /
• pp.1-6
• /
• 1991

In this study, intermediate thermo-mechanical treated Al-2.0 wt%Li, and Al-2.0 wt%Li-1.2 wt%Cu-1.0 wt%Mg-0.12 wt%Zr alloys were tested in tension at $10^{\circ}C$ and elevated temperature(100, 200 and $300^{\circ}C$). The results are follows : The tensile strength of Al-Li-Cu-Mg-Zr alloy is the highest but the elongation of Al-Li alloy is the highest(106%) among the all alloys in tension at $300^{\circ}C$. The Portervin-LeChartlier effect is showed in AI-Li-Cu-Mg-Zr alloy at 10 and $100^{\circ}C$, because of tangled dislocation by Mg and Cu. In the true stress-strain curves of all alloy, the peaks of stress at $300^{\circ}C$ are showed at the strain less than 0.1. In the binary alloy, the dynamic restoration process at 200 and $300^{\circ}C$ is nearly similar to dynamic recovery type. The hot deformation stress is decreased with increase of dynamic recovery degree, but the elongation is increased. When the strain the strain rate are constant, the temperature dependence of hot deformation stress is increased with increase of deformation temperature. The elongation and degree of dynamic recovery are decreased with increase of hot deformation activation energy, but the deformation stresses slightly increased.