• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.657-664
• /
• 2004

In this study, a fundamental experiment was carried out to investigate the frost formation on a cryogenic flat plate with/without temperature distribution from 230K to 160K under the convective flow. The effects of mixing ethanol as a condensable substance were also researched. From the test results, when surface temperature at the upstream is 230K, mass flux is high. On the other hand, when surface temperature at the downstream is 160K, mass flux is low. The degree of improvement to restrain frost formation by ethanol mixing is relatively larger at the upstream than at the downstream.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.7
• /
• pp.1022-1029
• /
• 1998

The relation of the inlet fuel distribution, velocity, and overall equivalence ratio to the stability of a lean burning no-swirl dump combustor was examined. Premixed or partially premixed natural gas was introduced into the air stream, which flowed to the dump region through an annular inlet pipe. Inlet air was preheated upto 400 deg.C. Combustion instability was observed to occur at higher value of equivalence ratio (> 0.6) as the degree of unpremixedness was increased. Instabilities exhibited a dominant frequency of ~ 500 Hz, which corresponded to a half wave mode of combustor. CH chemiluminescence and pressure fluctuations were in-phase when combustion instabilities occurred. Acetone LIF images revealed that there was a strong fuel concentration gradient across the inlet annulus. Phase resolved OH LIF images showed that inlet fuel distribution was affected by the combustion instabilities.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.546-549
• /
• 2004

This paper describes the electrical characteristics of the polymer lightning arresters(L.As) used to protect distribution lines and power facilities from surge. For the relative comparison, the characteristics assessment was done for 2 states of L.As before and after water immersion treatment. The L.As for the comparative test were immersed with water of $95[^{\circ}C]$ considered a severe condition. After the immersion treatment, the assessment was carried out for material analyses in chemical structure(FTIR : fourier transform infrared spectrophotometer). Electrical performance measured insulation resistance measurement, leakage current measurement, critical operation voltage measurement etc.. In addition to, the results were compared with those for the L.As deteriorated in the field. Thus, the accelerative deterioration degree of polymer materials by immersion treatment was evaluated, by which the structural defects of the polymer L.As could be inferred.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.140-143
• /
• 2000

The primary function of ZnO lightning arrester is to protect transmission and distribution equipment from overvoltages and to absorb electrical energy resulting from lightning or switching surges and form temporary overvoltage. However, ZnO lightning arrester are known to exhibit an increases in resistive current with time, the rate of increase being exacerbated with increasing applied voltage and ambient temperature. So, it is important to the leakage current measurement of ZnO lightning arrester. In addition, since the resistive leakage current caused by deterioration of ZnO lightning arrester mainly caused an increase of the third harmonic component, thereby it is possible the arrester degradation diagnosis by measuring the third harmonic component in the total leakage current. The leakage current and third harmonic component are measured and used to investigate the degradation diagnosis of ZnO element of arrester. Also the SEM photography is used to investigate the change of crystal structure of ZnO element with degradation.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.111-118
• /
• 2006

Underwater wet arc welds were experimentally performed on 11mm thick KR-RA steel plate using six different types of flux coated electrodes of 4.0mm diameter, KSKR, KSKT, USBL, JPUW, UWEA and UWEB. From analysis of bead appearance, detachability of weld slag, spatter occurrence and arc stability, JPUW gives the best result, and UWEB is superior to KSKR and KSKT. By experimental result of hardness distribution on the weld bonds, UWEB weld has the narrowest bond structure which is probable condition to get the best mechanical properties of weld. UWEB and JPUW welds have more even hardness distribution across weld deposit and base metal. Upon polarization test to measure the respondency of corrosion, the electrode of UWEB shows the most excellent degree due to the low open circuit potential difference.

• Bulletin of the Korean Chemical Society
• /
• v.11 no.1
• /
• pp.1-7
• /
• 1990

We present a theoretical investigation on the etching of an Al solid by $SiCl_4$ molecules at a collision energy of 600 eV. The classical trajectory method is employed to calculate Al etching yields, degree of anisotropy, kinetic energy distribution and angular distribution. The calculated results are compared with the reaction of a Cu solid by $SiCl_4$. The major products of the reaction are aluminum monomers and dimers together with considerable quantities of multimers. The Al solid shows better etching yield and better anisotropy than the Cu solid. This is consistent with the problem in the CMOS micro-fabrication of the CuAl and CuAlSi alloys. The relevance of these calculations for the dry etching of CuAl alloy is discussed.

• Communications of the Korean Mathematical Society
• /
• v.36 no.4
• /
• pp.671-684
• /
• 2021

The tenacity of the current paper is to find connections between various subclasses of analytic univalent functions by applying certain convolution operator involving generalized hypergeometric distribution series. To be more specific, we examine such connections with the classes of analytic univalent functions k - 𝓤𝓒𝓥^* (𝛽), k - 𝓢^*_p (𝛽), 𝓡 (𝛽), 𝓡^𝜏 (A, B), k - 𝓟𝓤𝓒𝓥^* (𝛽) and k - 𝓟𝓢^*_p (𝛽) in the open unit disc 𝕌.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.49-53
• /
• 2019

The temperature distribution and lifetime of molds were predicted by computer simulation analysis with various spraying and blowing process of high pressure die casting. After varying the spraying angle and time, the mold temperature, heat exchange and mold life were predicted. As the spraying angle increases, the maximum temperature of the mold decreases, which is because the spraying area increases and the heat exchange with the mold increases. Heat exchange occurs more actively in the blowing process than in the spraying process. This is because the cooling is not performed due to the steam generation. When the spraying angle is 50 degree, the minimum life of the mold is analyzed 200 times. After adjusting the blowing time from 5s to 3s, the minimum lifetime of the mold has been increased almost twice.

• Korean Journal of Plant Taxonomy
• /
• v.51 no.4
• /
• pp.363-371
• /
• 2021

Vicia bifolia Nakai (Fabaceae) and Cyperus compressus L. (Cyperaceae) have been ambiguous in terms of their distribution and taxonomic entities in Korea. The existence of these two taxa was confirmed when V. bifolia and C. compressus was found on Jellabuk-do, Gyeongsangnam-do, and Jeju-do. Vicia bifolia is similar to V. unijuga by having a pair of leaflets but is distinguished by the length of the petiole, the size and degree of longevity of the bracts, and the shape of the stipules. Cyperus compressus was found on Jeju-do, is similar to C. tenuispica, C. haspan, and C. flaccidus, but is distinguished by the branching pattern of the inflorescences and the size of scales and achenes. A description, differences from related species, a key to the taxa and photographs of Korean Vicia bifolia and Cyperus compressus are provided in this study.

• Journal of Environmental Health Sciences
• /
• v.9 no.2
• /
• pp.55-65
• /
• 1983

This survey was carried out to investigate the pattern of taking psychotropic drugs for 618 cases who visited 48 drugstores located as such four types of areas as business sections, gay quarters, residential sections and quasi-industrial areas from May, 1982 to March, 1983. The results are summarized as follows: I. The age distribution: The age group of 20-29 showed the highest distribution covering 35.6% as 220 out of 618 cases. The age groups of thirties and forties covered 23.0% and 19.0% respectively. The sex ratio was estimated as 1:1.86. 2. The occupational distribution: The unemployees composed the largest portion covering 53.7% as 332 out of 618. Above all the class of the housewives was 32.7%. 3. The marital status: The degree of distribution was higher on the sides of the group of married people than that of single and its percentage was 30.1. 4. The educational level: Most of the people who purchased the drugs had no knowledge of the effect of the drugs, and they covered 80.9%. 5. As for the motives, the twenties took psychotropic drugs in order to relief insomnia and that was the biggest major motive at the portion of 59.1%, 130 out of 618. 6. The age group of twenties who took the drugs for about 6 months showed the highest percentage of 52.7%. 7. The highest distribution appeared in the case that takes one or two tablets a day for less than 6 months. 8. The dosage distribution by the number of times taking the drugs The group of people that took the drugs more than 3 to 4 tablets a day as the number of 1 to 3 times covered 41.7\ulcorner0 of 187. 9. The most favorite psychotropic drugs: Lorazepam was showed to be the most favorite drugs by either male or female covered 50.9o70, 54.2\ulcornero respectively. 10. The motives of selecting drugs: The optional motives of selecting psychotropic drugs were showed 269 (43.5%) out of 618 cases that chose the drugs for themselves.