• Applied Chemistry for Engineering
• /
• v.32 no.6
• /
• pp.632-639
• /
• 2021

In this research, fluorine doping was performed to enhance the photocatalytic activities of WO₃ which were measured using methylene blue dye. WO_3-xF_x photocatalyts were prepared by a vaper phase fluorination during a sintering for preparing WO₃ photocatalysts from a WCl₆ precursor. The bandgap energy of WO₃ photocatalysts decreased from 2.95 eV to 2.54 eV, and the oxygen vacancies site increased by about 55% after fluorine doping. In addition, the initial degradation efficiency of methylene blue showed that the fluorine doped sample showed a 6-fold increase in photocatalytic activities from 10% to 60% compared to that of the untreated sample. It is believed that fluorine is doped to reduce the band gap of photocatalysts, enabling the catalytic activity with low energy, and that oxygen vacancies-generated surface defects increase the visible light absorption region of WO₃ photocatalysts, thereby increasing photocatalytic activity. In this study, it was confirmed that fluorine-doped WO_3-xF_x photocatalysts with an excellent photocatalytic activity can be manufactured easily using a one-step vaper phase fluorination that does not require a post-treatment process.

• Journal of Wetlands Research
• /
• v.21 no.2
• /
• pp.181-190
• /
• 2019

Recently, Low impact development techniques, a form of nature-based solutions (NBS), were seen cost-efficient alternatives that can be utilized as alternatives for conventional stormwater management practices. This study evaluated the effectiveness of an infiltration trench (IT) and a small constructed wetland (SCW) in treating urban stormwater runoff. Long-term monitoring data were observed to assess the seasonal performance and cite the advantages and disadvantages of utilizing the facilities. Analyses revealed that the IT has reduced performance during the summer season due to higher runoff volumes that exceeded the facility's storage volume capacity and caused the facility to overflow. On the other hand, the pollutant removal efficiency of the SCW was impacted by the winter season as a result of dormant biological activities. Sediment data also indicated that fine and medium sand particles mostly constituted the trapped sediments in the pretreatment and media zones. Sediments in SCW exhibited a lower COD and TN load due to the phytoremediation and microbiological degradation capabilities of the system. This study presented brief comparison LID facilities equipped with pre-treatment zones. The identified factors that can potentially affect the performance of the systems were also beneficial in establishing metrics on the utilization of similar types of nature-based stormwater management practices.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.9
• /
• pp.55-61
• /
• 2011

This study investigate the use of ultraviolet(UV) light with hydrogen peroxide($H_2O_2$) for Methyl Tert Butyl Ether(MTBE) degradation in photolysis reactor. The process in general demands the generation of OH radicals in solution at the presence of UV light. These radicals can then attack the MTBE molecule and it is finally destroyed or converted into a simple harmless compound. The MTBE removal by photolysis were mathematically described as the independent variables such as irradiation intensity, initial concentration of MTBE and $H_2O_2$/MTBE ratio, and these were modeled by the use of response surface methodology(RSM). These experiments were carried out as a Box-Behnken Design(BBD) consisting of 15 experiments. Regression analysis term of Analysis of Variance(ANOVA) shows significantly p-value(p<0.05) and high coefficients for determination values($R^2$=94.60%) that allow satisfactory prediction of second-order regression model. And Canonical analysis yields the stationery point for response, with the estimate ridge of maximum responses and optimal conditions for Y(MTBE removal efficiency, %) are $x_1$=25.75 W of irradiation intensity, $x_2$=7.69 mg/L of MTBE concentration and $x_3$=11.04 of $H_2O_2$/MTBE molecular ratio, respectively. This study clearly shows that RSM is available tool for optimizing the operating conditions to maximize MTBE removal.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.1
• /
• pp.241-262
• /
• 2021

This paper reviewed the necessity of a information and communication technology (ICT)-based smart livestock system as a development strategy for the animal life industry in the future. It also predicted the trends of livestock and animal food until 2050, 30 years later. Worldwide, livestock raising and consumption of animal food are rapidly changing in response to population growth, aging, reduction of agriculture population, urbanization, and income growth. Climate change can change the environment and livestock's productivity and reproductive efficiencies. Livestock production can lead to increased greenhouse gas emissions, land degradation, water pollution, animal welfare, and human health problems. To solve these issues, there is a need for a preemptive future response strategy to respond to climate change, improve productivity, animal welfare, and nutritional quality of animal foods, and prevent animal diseases using ICT-based smart livestock system fused with the 4th industrial revolution in various aspects of the animal life industry. The animal life industry of the future needs to integrate automation to improve sustainability and production efficiency. In the digital age, intelligent precision animal feeding with IoT (internet of things) and big data, ICT-based smart livestock system can collect, process, and analyze data from various sources in the animal life industry. It is composed of a digital system that can precisely remote control environmental parameters inside and outside the animal husbandry. The ICT-based smart livestock system can also be used for monitoring animal behavior and welfare, and feeding management of livestock using sensing technology for remote control through the Internet and mobile phones. It can be helpful in the collection, storage, retrieval, and dissemination of a wide range of information that farmers need. It can provide new information services to farmers.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.1
• /
• pp.19-28
• /
• 2021

Corrosion is the degradation of metals by reaction with the environment. It is difficult to completely remove. Corrosion proceeds rapidly after the protective barrier is destroyed, and several reactions occur that alter the composition and properties of the metal surface and local environments, such as diffusion of metal cations into the matrix, the formation of oxides, and local pH changes. The study of corrosion of steel and iron is of theoretical and practical interest and is receiving considerable attention. Acid solutions, which are widely used in industrial pickling, acid descaling, cleaning and acidification of oil wells, require the use of corrosion inhibitors to suppress corrosion attacks on metallic materials. Physical removal of rust requires expensive special equipment, and chemical removal of it can cause corrosion or shorten the life of the metal. In this study, an eco-friendly rust cleaner was developed using cosmetics and food materials by applying the concept of perm reducing agent and chelate, and applied to remove rust from industrial and hot water pipes and various industrial devices. As a result, it was found that rust cleaners remove rust more effectively and safely compared to conventional treatment methods. At the same time, the rust removal efficiency was 1.75 to 2.5 times better for industrial piping and 1.56 to 2.2 times better for boiler hot water than conventional methods.

• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.6
• /
• pp.405-415
• /
• 2021

MMBR system has been suggested as a promising system to resolve harvesting problems induced from low settling efficiency of microalgae. And recently, a lot of research on reducing fouling at the MMBR system has investigated focused on EPS in many cases. EPS of microalgae mainly consists of polysaccharides and protein components, and is produced through photosynthesis and nitrogen-carbon metabolic pathways. Especially, P-EPS is one of major compounds which occur membrane fouling phenomenon, as its hydrophobic protein components cause floc formation and cake layer accumulation. And it is already known that almost every microalgae can metabolize P-EPS or Chl-a when nitrogen sources as a substrate is insufficient or exhausted situation. With the above backgrounds, uptake rates of P-EPS or Chl-a by Scenedesmus quadricauda according to the type of carbon source and nitrogen concentration were evaluated in order to verify correlation between carbon source vs P-EPS production, and indeed Scenedesmus quadricauda uses P-EPS or Chl-a when the amounts of nitrogen sourc es in the feed is not satisfied. As a result, it was shown that P-EPS and Chl-a production were increased proportional to nitrogen concentration under organic carbon condition. And especially, the amo unts of P-EPS and Chl-a in the cell were diminished with the nitrogen source becomes insufficient or exhausted. Because P-EPS accelerates fouling at the MMBR system, P-EPS degradation by Scenedesmus quadricauda in order to get nitrogen source may contribute to reducing fouling. About a affects of N-consumed Chl-a to the MMBR fouling, more survey is needed. On the contrary, considering the purpose of MMBR system of this study, i.e. harvesting useful high value microalgae efficiently feeding adequate industrial process wastewater, it seems like difficult to maintain satisfied metabolic activity and to harvest with high yield rate using nitrogen-poor MMBR feed.

• Applied Chemistry for Engineering
• /
• v.33 no.2
• /
• pp.159-165
• /
• 2022

To enhance the photocatalytic activities of WO₃ photocatalysts, fluorine doping was performed to induce the oxygen vacancies. Both plasma and direct vaper fluorination were carried out for fluorine doping, and photocatalytic activities were examined by using methylene blue dye. Oxygen vacancies of the plasma and direct vaper fluorinated WO₃ photocatalysts were measured to be 14.65 and 18.59%, which increased to about 23 and 56% at pristine WO₃ photocatalysts. The degradation efficiency of methylene blue was also determined about 1.7 and 3.4 times higher than pristine WO₃ photocatalysts, respectively, depending on oxygen vacancies increased. In addition, it was confirmed that the bandgap process energy decreased from 2.95 eV to 2.64 and 2.45 eV after fluorine doping. From this result, it is considered that the direct vaper fluorination has an advantage for increasing the photocatalytic activities of WO₃ compared to that of the plasma fluorination.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6A
• /
• pp.765-778
• /
• 2008

Performance Profiles are essential to predict the performance variation over time for the bridge management system (BMS) based on risk management. In general, condition profiles based on experts opinion and/or visual inspection records have been used widely because obtaining profiles based on real performance is not easy. However, those condition profiles usually don't give a good consistency to the safety of bridges, causing practical problems for the effective bridge management. The accuracy of performance evaluation is directly related to the accuracy of BMS. The reliability of the evaluation is important to produce the optimal solution for distributing maintenance budget reasonably. However, conventional methods of bridge assessment are not suitable for a more sophisticated decision making procedure. In this study, a method to compute quantitative performance profiles has been proposed to overcome the limitations of those conventional models. In Bridge Management Systems, the main role of performance profiles is to compute and predict the performance of bridges subject to lifetime activities with uncertainty. Therefore, the computation time for obtaining an optimal maintenance scenario is closely related to the efficiency of the performance profile. In this study, the Response Surface Method (RSM) based on independent and important design variables is developed for the rapid computation. Steel box bridges have been investigated because the number of independent design variables can be reduced significantly due to the high dependency between design variables.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.4
• /
• pp.414-419
• /
• 2005

This study was performed to compare the treatment efficiencies of two media, newly developed Bio-rock and conventional gravel, in soil clothing contact oxidation process. The composition of synthetic wastewater were $COD_{Cr}$ $150{\sim}370\;mg/L$, $BOD_5$ $150{\sim}270\;mg/L$, T-N $20{\sim}60\;mg/L$, T-P $5{\sim}25\;mg/L$, pH 7 and 2 mL/L of trace element solution. The experiment using two reactors was comparatively conducted for the flow rate of 40 L/d for 13 months, respectively. Initially Bio-rock reactor was increased to pH 12 due to $Ca(OH)_2$ with hydration of cement, but gravel reactor was dropped to pH 4 due to the degradation of organic material and nitrification. This significant pH variation deteriorated the growth and activity of microorganism. But the high pH of Bio-rock seems favorite to ammonia stripping and precipitation of phosphate. Such pH variation of Bio-rock and gravel reactors were finally stabilized to pH 8 and pH 6, respectively. The removal efficiencies of organic compounds from Bio-rock reactor were 96% of $COD_{Cr}$, 98% of $BOD_5$, 80% of T-N and 85% of T-P which stably coping against variation of influent concentration. But those of gravel reactor were 96% of $COD_{Cr}$, 96% of $BOD_5$, 42% of T-N and 40% of T-P, respectively. The Bio-rock was 2 times higher than T-N and T-P in treatment efficiency. And electron-microscopic examination showed that Bio-rock was more favorable to microbial adherence than gravel. The microbial populations were $5.2{\times}10^6\;CFU/mL$ of Bio-rock reactor compared to $2.6{\times}10^6\;CFU/mL$ in gravel reactor. In result Bio-rock was favor to microbial adherence and high treatment efficiency in spite of variation of influent concentration which had the advantages in saving running time and reducing site requirement.

• Journal of KIISE:Information Networking
• /
• v.35 no.2
• /
• pp.99-111
• /
• 2008

In recent years, the needs for WLANs(Wireless Local Area Networks) technology which can access to Internet anywhere have been dramatically increased particularly in SOHO(Small Office Home Office) and Hot Spot. However, unlike wired networks, there are some unique characteristics of wireless networks. These characteristics include the burst packet losses due to unreliable wireless channel. Note that burst packet losses, which occur when the distance between the wireless station and the AP(Access Point) increase or when obstacles move temporarily between the station and AP, are very frequent in 802.11 networks. Conversely, due to burst packet losses, the performance of 802.11 networks are not always as sufficient as the current application require, particularly when they use TCP at the transport layer. The high packet loss rate over wireless links can trigger unnecessary execution of TCP congestion control algorithm, resulting in performance degradation. In order to overcome the limitations of WLANs environment, MAC-layer LDA(Loss Differentiation Algorithm)has been proposed. MAC-layer LDA prevents TCP's timeout by increasing CRD(Consecutive Retry Duration) higher than burst packet loss duration. However, in the wireless channel with high packet loss rate, MAC-layer LDA does not work well because of two reason: (a) If the CRD is lower than burst packet loss duration due to the limited increase of retry limit, end-to-end performance is degraded. (b) energy of mobile device and bandwidth utilization in the wireless link are wasted unnecessarily by Reducing the drainage speed of the network buffer due to the increase of CRD. In this paper, we propose a new retransmission module based on Cross-layer approach, called BLD(Burst Loss Detection) module, to solve the limitation of previous link layer retransmission schemes. BLD module's algorithm is retransmission mechanism at IEEE 802.11 networks and performs retransmission based on the interaction between retransmission mechanisms of the MAC layer and TCP. From the simulation by using ns-2(Network Simulator), we could see more improved TCP throughput and energy efficiency with the proposed scheme than previous mechanisms.