• 동력기계공학회지
• /
• 제8권4호
• /
• pp.31-37
• /
• 2004

The damping capacity and strength of Fe-2Al-26Mn alloys have been studied for the development of new materials with high strength and damping capacity. Particularly, the effect of ${\alpha}'\;and\;{\varepsilon}$ martensite phase, which constitutes the microstructure of cold rolled Fe-Al-Mn alloys, has been investigated in terms of the strength and damping capacity of the alloys. The damping capacity rises with increasing the degree of cold rolling and reveals the maximum value at 25% reduction. The damping capacity is strongly affected by the volume fraction of ${\varepsilon}$ martensite, while the other phases, such as ${\alpha}'$ martensite and austenite phase, actually exhibit little effect on damping capacity. Considering that tensile strength increases and elongation decreases with increasing the volume fraction of ${\alpha}'$ martensite, it is proved that tensile strength is mainly affected by the amount of ${\alpha}'$ martensite.

• 한국전기전자재료학회논문지
• /
• 제23권11호
• /
• pp.880-885
• /
• 2010

The Angle Ring and Cap which is called pressboard are settled at the primary and secondary coil winding of 154 kV transformer that can reduce effectively distance of insulation. As it has not manufactured pressboard of Angle Ring and Cap for high voltage grade, insulation components industry especially high voltage transformer has not participate in a competition with worldwide yet. That's why is difficult to make an specialized shape of insulation components of high voltage grade. Therefore it has finally completed to make an deformation manufacturing utility using an bellowed special analysis tools. This study that uses various analysis program determining optimum shape about insulation of Angle Ring and Cap which is related life of high voltage transformer. In addition to develop forming equipment with an specialized five steps pressing. That is also based on the mechanical strength evaluation and test, it is investigated optimized processing components.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.84-88
• /
• 2009

The nickel-based alloy Nimonic 80A possesses strength, and corrosion, creep and oxidation resistance at high temperature. The exhaust valves of low speed diesel engines are usually operated at temperature levels of 400-$600^{\circ}C$ and high pressure to enhance thermal efficiency and exposed to the corrosion atmosphere by the exhaust gas. Also, the exhaust valve is subjected to repeated thermal and mechanical loads. So, the nickel-based alloy Nimonic 80A was used for the large exhaust valve spindle. It is composed a 540mm diameter head and a 125mm diameter stem. It is developed large products by hot closed-die forging. Manufacturing process analysis of the large exhaust valve spindle was simulated by closed die forging with hydraulic press and cooled in air after forging. The preform was heated to $1080^{\circ}C$ Numerical calculation was performed by DEFORM-2D, a commercial finite element code. Heat transfer can be coupled with the deformation analysis in a non-isothermal deformation analysis. Mechanical properties of the large exhaust valve spindle were evaluated by the variety of tests, including microstructure observation, tensile, as well as hardness and fatigue tests, were conducted to evaluate the mechanical properties for head part of exhaust valve spindle.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 추계학술대회 논문집 전기물성,응용부문
• /
• pp.251-254
• /
• 2001

Internal and external forces may be applied on the power cable in the both process of transportation and installation. Even though the EHV power cables have the structure of metal sheath and plastic jacket etc. to minimize these negative influences, the unusual forces result in the unexpected deformation of the cable. Compressing moulded XLPE model cable sheets were prepared and locally dented with round-edge and square-edge tools. All data were analyzed employing Weibull distribution. The breakdown strength of dented molded specimens showed lower values than the normal ones by 10-60%.

• 한국안전학회지
• /
• 제16권2호
• /
• pp.97-102
• /
• 2001

Anchors are often used in construction of foundations such as transmission towers to resist uplifting forces. When plate anchors are embedded in soft clay, they may undergo a deformation under the pressure of sustained load. In soft saturated clays, the suction force can be a large par of the ultimate uplift capacity. This study is to present recent laboratory model test results conducted to evaluate the nature of variation of the suction force for plate anchors with shear strength and embedment ratio. The ratio of F$_{s}$Q$_{n}$ versus H/D in bentonite decreases with the increase of the embedment ratio.o.o.

• 지질공학
• /
• 제32권1호
• /
• pp.59-72
• /
• 2022

본 연구는 부산 기장지역의 백악기 흑운모 화강암에 대하여 삼차원 개별체 수치해석 기반의 응력-변형 해석을 수행하고 절리성 암반의 강도 및 변형특성을 평가하였다. 절리성 암반의 역학적 특성에 대한 규모효과 및 REV를 규명하기 위한 워크플로우가 제시되었으며 연구지역에서 결정된 REV(representative elementary volume) 크기의 DFN(discrete fracture network) 큐브 블록에 대한 블록강도, 변형계수, 전단탄성계수, 체적탄성계수 등의 강도 및 변형 파라미터가 산정되었다. 연구지역의 역학적 REV 크기는 15 m 큐브로 평가되었으며 DFN 큐브 블록의 평균 블록강도 및 평균 변형계수는 각각 신선암의 52.8% 및 57.7%로 추정되었다. 연구지역의 절리성 암반은 역학적으로 뚜렷한 직교이방성을 나타내는 것으로 평가되었으며 삼차원 수치해석을 통하여 산정된 변형 파라미터를 이용하여 선형-탄성의 직교이방성 구성모델이 도출되었다. 연구지역에 대한 직교이방성 구성모델은 등가의 연속체 해석을 통한 터널 및 지하공간의 안정성 평가에 활용될 수 있다.

• 대한조선학회논문집
• /
• 제38권4호
• /
• pp.75-82
• /
• 2001

건조 후 수행하는 수압시험 또는 화물의 적재 등과 같은 정하중은 파랑변동하중에 비하여 선체구조물에 상당히 큰 응력을 유발한다. 이러한 정하중이력에 의하여, 선체구조물의 응력집중으로 인해 피로강도가 문제되는 용접이음부에서는, 재료의 탄소성 거동에 의하여 초기용접잔류응력이 상당히 이완될 것으로 예상된다. 따라서, 이러한 용접이음부의 피로강도를 평가할 때에는 이완된 잔류응력의 영향을 고려하는 것이 보다 합리적이다. 본 연구에서는 선체구조물의 여러 가지 용접형태 중 Padding plate가 용접된 형태에 대하여 정하중이력($0.5{\sigma}Y,\;0.85{\sigma}Y$)에 의한 초기 용접잔류응력의 변화를 측정하며, 잔류응력의 변화가 피로강도에 미치는 영향을 검토한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.90-93
• /
• 2000

Al ally 7050 has been developed for higher strength and improved property against stress-corrosion cracking. Since the use of this alloy becomes more important for forged aircraft structural components. $\phi$ 65mm extruded billet has been forged for a highly-stressed aircraft parts. After forging processing and heat treatment, the forged parts showed undesirable microstructure caused by severe local grain coarsening at the surface layer and heavily-localized metal flow, the analysis of resulted in degraded mechanical properties. The above results have been compared to simulation by using the DEFORM-3D and those showed the thermomechamical processing must be optimized in terms of forging temperature, strain rate and deformation amount. To prevent the grain coarsening at the surface layer $\varepsilon$ heavily-localized grain flows.

• 한국농공학회논문집
• /
• 제63권2호
• /
• pp.41-50
• /
• 2021

The asphalt pavement industry has introduced the warm-mix asphalt (WMA) as a mean of energy saving and environmentally safe technology, because the WMA mixture can be mixed and compacted at 30℃ lower than conventional hot-mix asphalt (HMA) at 160℃ or higher. The implementation of WMA can be a good option for paving operations for rural road in remote place, not only due to energy saving and environmental issues, but also lower working temperature. Using WMA technology, the cooled-down asphalt mixture can be still compacted to meet the quality requirement in narrow winding rural road in remote places. Therefore, this study is designed to evaluate engineering properties of WMA binders and concretes, which were prepared for rural road pavement. The objective of the study was to evaluate and suggest proper fundamental properties level of the WMA concrete for rural road pavement. The kinematic viscosity test result indicated that the WMA binders used in this study were effective for compaction at lower temperature, i.e., at 115℃, compared to the HMA binder. According to strength property analyses, it was found that the WMA concrete was acceptable for rural road pavement even though it was compacted at 30℃ lower level. Since the deformation strength (SD) of 3.2 MPa was found to satisfy rutting and cracking resistance minimum guidelines, this value was suggested as a minimum SD value for rural road pavement, considering lack of maintenance program for rural area.

• 한국자동차공학회논문집
• /
• 제14권1호
• /
• pp.79-85
• /
• 2006

CFRP(Carbon Fiber Reinforced Plastics) of the advanced composite materials as structural materials for vehicle, has a wide application in light-weigh structural materials of airplanes, ships and automobiles because of high strength and stiffness, However, there is a design variable to be considered in practical application of the laminate composite materials, these materials are vulnerable to transverse impact. This paper is to study the effects of stacking sequence and curvature on the penetration characteristics of composite laminate shell. They are stacked to $[0_3/90_3]S,\;[90_3/0_3]s\;and\;[0_2/90_3/0]s,\;[90_2/0_3/90]s$ and their interlaminar number two and four. They are manufactured to various curvature radius (R=100, 150, 200mm and $\infty$), When the specimen is subjected to transverse impact by a steel ball, the velocity of the steel ball was measured both before and after impact by determing the time for it to pass two ballistics-screen sensors located a known distance apart. The critical penetration energy of specimen A and B with less interfaces were a little higher than those of C and D. As the curvature increases, the critical penetration energy increases linearly because the resistance to the in-plane deformation as well as bending deformation increases, which need higher critical penetration energy. The specimen A and C have higher critical penetration energy than B and D because of different stacking sequences. We examined crack length through a penetration test. For the specimen A with 2interfaces, the longest circumferential direction crack length were observed on the first interface from the impact point. For the specimen B 4-interface, the longest circumferential direction crack length were observed on the second interface from the impact point.