• Journal of Korean Society for Quality Management
• /
• v.30 no.2
• /
• pp.152-159
• /
• 2002

An acceptance sampling plan for products manufactured from a production process with variable fraction defective is developed. We consider a situation where defective products have short lifetimes and non-defective ones never fail during the technological life of the products. An acceptance criterion which guarantee the out going quality of accepted products is derived using the prior information on the quality of products. Numerical examples are provided.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.34
• /
• pp.3-26
• /
• 2007

Product liability law lies at the center of the modem world. This law concerns liability for damages arising from the commercial sale of a product that causes personal injury or property damage because it was defective or falsely represented. One engaged in the business of selling or otherwise distributing products who sells or distributes a defective product is subject to liability for harm to persons or property caused by the defect. In short, product defectiveness is the heart of products liability law. Regardless of the underlying cause of action, the plaintiff in nearly every products liability case must prove that the defendant's product contained an unnecessary hazard that caused the harm. The purpose of this paper is to clarify the meaning of the product defectiveness to products liability claims in China. In China, Product to include most movable personal property, but to exclude services. And a product is defective when, at the time of sale or distribution, it contains a manufacturing defect, is defective in design, or is defective because of inadequate instructions or warnings.

• Proceedings of the Korean Reliability Society Conference
• /
• 2000.11a
• /
• pp.373-373
• /
• 2000

Bum-in procedures are developed far limited failure populations in which defective products fail soon after they are put in operation and non-defective ones never fail during the technological life of the products. The situation where products are produced from a production process with variable fraction defective is considered. Bum-in schemes guaranteeing pre-specified outgoing quality of products are derived using the mixed binomial prior distribution for the number of defectives in a batch.

• The Korean Society of Law and Medicine
• /
• v.8 no.1
• /
• pp.235-277
• /
• 2007

In Product Liability law, the 'defection' of the manufactured products is its key concept, defined in detail. The concept had been already developed through the precedents and theories for the past years even before the PL law was enacted and the concept was listed. Especially, the medicine products need the different approach, because they might directly harm to the human life and body due to their being injected or taken, unlikely other manufactured articles. Since the medical products have the double contradictory functions such as effects and side effects, the defection decisions become so difficult. However, because there are high concerns that wrong medical products will directly harm the human life and body, the decision standards should be more strengthened. The decision standards should include the risk-effect standard as the considered components and make the customer-expecting standard as the final standard. The decision time for defection should be made considering the science technology level when the medical products were provided, not when the accident occurred. It is the most important for the manufacturers to prevent the damages by making and selling the non-defective medicine products for themselves, rather than by taking the legal remedy means afterwards. Therefore, the non-defective guidelines for the medicine manufacturers will help increase the effects and minimize the side-effects.

• Proceedings of the Korean Reliability Society Conference
• /
• 2002.06a
• /
• pp.275-279
• /
• 2002

A Bayesian acceptance sampling plan for limited failure populations are developed. We consider a situation where defective products have short lifetimes and non-defective ones never fail during the technological life of the products. An acceptance criterion which guarantees the out going quality of accepted products is derived using the prior information on the quality of lots submitted for inspection. Numerical examples are provided.

• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.2977-2983
• /
• 2023

During normal operation, some parts of the fission product in the defective fuel rods can release into the primary loops in PWR and the escape rate coefficients are widely used to assess quantitatively the release behaviors of fission products in the industry. The escape rate coefficients have been standardized and have been validated by some drilling experiments before the 1970s. In the paper, the model to determine the escape rate coefficients of fission products has been established and the typical escape rate coefficients of noble gas and iodine have been deduced based on the measured radiochemical data in one operating PWR. The result shows that the apparent escape rate coefficients vary with the release-to-birth and decay constants for different fission products of the same element. In addition, it is found that the escape rate coefficients from the defective rod with large defects are much higher than the standard escape rate coefficients, i.e., averagely 4.4 times and 1.8 times for noble gas and iodine respectively. The enhanced release of fission products from the severe secondary hydriding of several defective fuel rods in one cycle may lead to the potential risk of the temporary shutdown of the operating reactors.

• Transactions of Materials Processing
• /
• v.13 no.4
• /
• pp.359-364
• /
• 2004

In the multi-stage former, a manufacture of hexagonal fitting nut was generated in a defective products about 70∼80% in the industry field. Products generated in defects manufactured to be a machining about 60%. Additional process increased a product cost and decreased a product rate. Therefore, it is important to predict and design a preform reducing defective products in the early stage of process design. So in the study Defects for manufacturing hexagonal fitting nut verified a cause through the finite element simulation. To reduce a defective generation. a preform designed and a designed preform verified through the finite element simulation. In conclusion, a generated defects when a hexagonal fitting nut manufactured should reduce if a round dimension of preform reduced and a part of opposition angle distributed in plenty a volume.

• Korean Management Science Review
• /
• v.33 no.3
• /
• pp.89-103
• /
• 2016

In this paper, we design sampling inspections and service capacities simultaneously for multi-products. Products are supplied in batches after rectifying inspections, that is, rejected lot is subject to total inspection and defective products are reworked to good ones. When supplied, all defective products are uncovered and returned to service. Particularly, we extend Kim [1] by introducing the fixed costs of providing services and show that the cost function of a product is no longer linear or convex in terms of the level of service provision. We develop a framework for a product to deal with this joint design problem and a dynamic programming algorithm for multi-products which allocates the given number of the total service capacities among products with the considerably smaller computations than the total number of possible allocations.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.35 no.1
• /
• pp.97-109
• /
• 2010

In this paper, we study a joint design problem of sampling inspections and service capacities for multi-products. Products are supplied in batches after rectifying inspections, that is, rejected lots are 100% inspected and defective products are reworked to good ones. When supplied, all defective products are uncovered through total inspection and returned to service. By exploiting the first and second order properties of the objective function, we identify the optimal inspection policies and service capacities for individual products, and develop allocation algorithms to obtain an optimal allocation of the limited total service capacity to products with the small number of computations.

• Proceedings of the Safety Management and Science Conference
• /
• 2001.05a
• /
• pp.241-251
• /
• 2001

Subsequently in Korea product liability has been introduced. The position of consumers for defective products have been disadvantageous. Defective products should be broght under the law. Then, while consumers would be largely protected, a producer would take the heavy responsibility by law, Therefore, a producer would not be able to take countermeasures for product liability. Object of this paper to investigate and analyze the actual state of management for product liability in advanced countries, and to join it with our quality management system.