• Journal of the Korea Furniture Society
• /
• v.24 no.3
• /
• pp.302-308
• /
• 2013

To collection of field data for development of maintenance manual of Han-ok, we investigated defects which occurred in members of Han-ok by field investigation. The noticeable defects were wood cracks, gaps that developed between wood pillar and wall or wood window frame and tenon joints. The most common biological defect was blue stain which was created in log. The mold generation was observed on exterior wood and wall which get wet by precipitation. The gaps between members of Han-ok pointed out as defect that is urgently improved by residents of Han-ok. The reason is mainly due to poor of insulation in winter by bad confidentiality. The maintenance work of defect such as gap was conducted personally. As a result, the repair parts were ugly for unfamiliar repair work.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.5
• /
• pp.392-398
• /
• 2013

This study investigated the effect of test zone selection for evaluating bending strength of visually graded lumber. This will contribute to the understanding of two different methods under different standards. In method I, the major defect was randomly placed in the test specimen. In method II, the major defect was randomly placed in the maximum moment zone (MMZ). The results showed that the method II is more accurate for reflecting the effect of defects governing the grade of lumber. Unless the maximum strength-reducing defect (MSRD) is placed in MMZ, the evaluated value would be higher than that of MSRD. For evaluating the modulus of rupture (MOR) of visually graded lumber in test set-up of Method I, the Eq. (5) needs to be considered.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.5
• /
• pp.16-23
• /
• 2007

This study was performed as part of a research project aimed at developing an ultrasonic computed tomography (CT) system of wood for field application. In this reports, we investigate the variation of wave velocities on the cross section of real size wooden structural member to confirm the reason of image distortion on CT image of wood, and then proposed a new image reconstruction method by considering the velocity variation on wood cross section. First of all, the effect of wood anisotropy on ultrasonic velocities of wooden members was investigated. Based on the relationship between ultrasonic velocity and annual ring angle, which was obtained from test results of small clear specimens, ultrasonic velocities of each measuring angle were predicted. Next, they were compared with the ultrasonic velocities measured on five wood disks. There were very large differences between predicted and measured results, thought to be caused by the skewing effect of ultrasound and the presence of juvenile-wood. Based on these findings, a new method was proposed to reconstruct cross-sectional image of wood. By using this method, some distortions on reconstructed images could be removed, and defects were more easily and clearly detected. The minimum size of detectable defect was decreased remarkably, from 33 mm to 13 mm. However, the size of the detected defect was enlarged and the position somewhat shifted to the specimen surface on the CT images, which was also thought to be caused by the skewing effect of ultrasound. Additional research has been planned to solve these problems.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.2
• /
• pp.31-37
• /
• 2003

Among the nondestructive evaluation (NDE) methods for wood defect detection, ultrasonic wave has been considered as competitive technique in terms of economics and workability. Until now, researches on application of NDE methods for wood have focused mainly on standing tree and logs. Recently, some attempts have been conducted with NDE technique, for evaluation of wooden structural members. However, wooden structural members are different from others (standing tree or log) in various aspects. Expecially when some parts or whole member are covered with other materials, they can't be evaluated appropriately on general NDE methods. For the purpose of development of proper NDE technique for the wooden structural members, the ultrasonic wave transmission process investigated on artificial defect in wood. First, various types of transmission process were assumed, and then the transmission times were predicted respectively. Predicted times were compared with the measured time of ultrasonic wave and then a suitable type of transmission process is determined. In case of the ultrasonic wave doesn't transmit directly due to defect, it is reflected once only at the opposite surface of member, and the path is accord with the line of shortest length.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.1
• /
• pp.463-469
• /
• 2020

People enjoy more leisure time these days as the government introduced the workweek last year and there is a growing interest on living healthy life. Amidst such change in society, trekking in forest has gained popularity along more people spending leisure time by walking for health. As a result, there are many scenic trails being built using wood deck. Usually certain parts of trails are built with wood deck where the path maybe too dangerous for walking or where nature needs to be protected. However wood material used for deck is easily prone to defects which can lead to safety issues. This study aims to understand the differences by materials used for wood deck and to investigate a link between different materials used and causes for defect occurrence. And further, the study aims to identify materials and construction methods for high workability and safety. The study was able to conclude that different materials used and different construction methods of applied for wood deck yield different results in terms of workability and defect occurrence.

• Proceedings of the Korean Institute Of Construction Engineering and Management
• /
• 2008.11a
• /
• pp.914-917
• /
• 2008

This paper was to discuss the case and cause of debonding defect of wood floor board in apartment house by investigating actual survey. Most frequent defect in wood floor board was debonding of floor board. Scratch, gap and crack of floor board were also found in floor board installment work. Causes of debonding of floor board is shrinkage of cement mortar beneath floor board and expansion of floor board. Haste in floor board work did not provide enough time to dry cement mortar fully, which led to continue to dry after the installment of floor board. It caused moisture movement toward wood floor board. Accordingly, Before floor board work, careful consideration on moisture condition of cement mortar and enough curing time to eliminate the effect of moisture are taken into.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.83-89
• /
• 2006

Because the surface of pine wood is very soft, there have been many attempts, like as surface coating, resin impregnation, and densificationt, to harden the surface of wood for its interior use. This study was carried out for surface hardening of pine wood by laminating of melamine resin sheet. The effect of laminating method on the characteristics of melamine resin sheet-laminated wood(MLW) was investigated. Flat-sawn softwoods were suitable for MLW making. And the pre-drying of wood at $105^{\circ}C$ for 30min, before laminating, was effective for preparing of defect-free MLW. The abrasion resistance of pine wood was greatly improved by laminating of melamine resin sheet on its surface. Consequently, the laminating of melamine resin sheet was proved to be a favorable method for improvement of surface abrasiveness of pine wood.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.2
• /
• pp.164-172
• /
• 2013

The purpose of this research was development of quantitative ultrasonic test methodology for detecting internal defects in members of ancient wooden building. Connection part between wooden members and/or contacted or hidden part by wall of ceiling or other construction materials make it hard to apply direct way of ultrasonic test. So indirect way of ultrasonic test needed to be applied. Test methodology with newly developed prototype of ultrasonic system was proposed. Homogeneous material with polypropylene was also tested for establishing the criterion. Results showed that TOF(time of flight)-energy and pulse length were found out to be proper ultrasonic parameters for predicting depth of defect in wood different from polypropylene. It was not possible to directly apply prediction equation derived from polypropylene. Newly established prediction equation shows coefficient of determination of 0.73 for wood. Finally, defect of replaced rafter members was predicted with the coefficient of determination of 0.32. Various aspects of ultrasound propagation in wood including anisotropy need to be carefully considered to raise up the prediction accuracy.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.2
• /
• pp.91-99
• /
• 2001

In this study the possibility of classifying wood surface defects by image processing technique was investigated. An algorithm for the classification of wood surface defects, such as knot, check, and bark, on three Korean domestic species, Pinus densiflora, Quercus acutissima, and Carpinus laxiflora was also developed. Filtering was executed to separate dummies from the labels including real defect. Error rates in classifying knots on Pinus densiflora and Quercus acutissima were lower than 1% and error rates. In classifying check and bark in Quercus acutissima and Carpinus laxiflora could be lowered to below 13%.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.25 no.3
• /
• pp.1-11
• /
• 1997

This study aims to estimate the relative importance of quality management items through the defect analysis in the landscape construction process. The RIQMI are decided by the defect coefficient and it's cause weight. The defect items in the landscape construction process were classified by 56 items based on the classification form of '96 landscape architectural construction standard and the cause pattern were categorized 4 types as design, material, construction, and environment factors. To analyze the defect coefficient and the aucse weight by defect, the researcher surveyed the questionnaires on the 103 engineers and the 31 experts on the landscape architectural construction. The result of this study are as follows. The relative importance by facilities pattern turn out to be much higher construction, material fator than design. environment factor in wood facilities, paving facilities, and steel facilities, the RIQMI is very high in timber crack, timber vending, faulty of timber against decay, welding faulty of steel facilities in material factor, and timber crack, faulty of timber against decay, finish faulty of steel facilities, welding faulty of steel facilities in construction factor.