• Journal of Sensor Science and Technology
• /
• v.6 no.2
• /
• pp.163-171
• /
• 1997

CdS thin films for window material of solar cell were prepared by close spaced vapor transport deposition system and annealed at different temperatures. The structural, electrical, and optical properties of as-deposited and annealed CdS films were investigated as functions of substrate and annealing temperatures. The CdS thin films were grown perpendicularly to the substrate along the (002)plane with hexagonal structure regardless of the preparation conditions The resistivity of the CdS film deposited was increased gradually from $60{\Omega}cm$ for $25^{\circ}C$ to $2{\times}10^{4}{\Omega}cm$ for $300^{\circ}C$. The optical transmittance at the substrate temperature of $25^{\circ}C$ was about 80% in the the visible spectrum. The resistivity increased monotonically, and the optical transmittance was decreased substantially with annealing temperature due to the increased defect density in the CdS film.

• Journal of the Korea Convergence Society
• /
• v.9 no.10
• /
• pp.7-12
• /
• 2018

In today's rapidly growing contemporary society, there is a tendency for demand to automate production processes by utilizing the vision system. In general, image recognition is mainly concerned with embossed characters such as license plates, and research on recognition of intaglio characters is very limited. Especially, intaglio characters, which are marked on rubber related products such as tire surfaces, have difficulty in recognizing characters or numbers through image because the difference in brightness with surrounding is not so large. In this paper, we propose a system to improve the recognition rate of characters marked on intaglio rubber products such as tire surfaces. Also, it can be applied flexibly according to the lighting environment. Through the proposed system, production and inventory management and defect detection can be processed quickly by applying to the production process of tire and rubber products.

• Journal of the Korean Society of Safety
• /
• v.32 no.2
• /
• pp.27-33
• /
• 2017

This study is intended to identify issues on the basis of investigating the actual state of laboratory environment and outlet circuit, and derive end states by expressing sequences from the initiating event of disaster to accident in leakage current, poor contact and overload through ETA(event tree analysis). To this end, this study investigated the actual state of electric equipment of laboratory at universities in all parts of country. And it is shown that most of them are failure in electric work and user negligence in the investigation of actual state. It is found that there is earth fault and defect in wire diameter in the failure of electric work and the problem of partial disconnection due to wire bundling and poor contact in user negligence. Outlet-related component, failure rate and initiating events are composed of a total of 41 initiating events, i.e., 30 internal initiating events and 11 external initiating events. And end states are composed of a total of 15 parts, i.e., 3 electric power parts and 12 safety parts. Earthing class 3 is the most important safety device against leakage current (initiating event). And in case of poor contact, it is necessary for manager to check thoroughly because there is no safety device. In case of overload/overcurrent, when high-capacity equipment is connected, a molded case circuit breaker, safety device, worked. However, in most cases, it is verified that this doesn't work. This study can be utilized as electric equipment safety guide for laboratory safety manager and managers.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.32 no.6
• /
• pp.524-529
• /
• 2006

For the repairing of bone defect, autogenous or allogenic bone grafting remains the standard. However, these methods have numerous disadvantages including limited amount, donor site morbidity and spread of diseases. Tissue engineering technique by culturing stem cells may allow for a smart solution for this problem. Adipose tissue contains mesenchymal stem cells that can be differentiate into bone, cartilage, fat or muscle by exposing them to specific growth conditions. In this study, the authors procured the stem cell from buccal fat pad and differentiate them into osteoblast and are to examine the bone induction capacity. Buccal fat-derived cells (BFDC) were obtained from human buccal fat pad and cultured. BFDC were analyzed for presence of stem cell by immunofluorescent staining against CD-34, CD-105 and STRO-1. After BFDC were differentiated in osteogenic medium for three passages, their ability to differentiate into osteogenic pathway were checked by alkaline phosphatase (ALP) staining, Alizarin red staining and RT-PCR for osteocalcin (OC) gene expression. Immunofluorescent and biochemical assays demonstrated that BFDC might be a distinguished stem cells and mineralization was accompanied by increased activity or expression of ALP and OC. And calcium phosphate deposition was also detected in their extracelluar matrix. The current study supports the presence of stem cells within the buccal fat pad and the potential implications for human bone tissue engineering for maxillofacial reconstruction.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.110-121
• /
• 2009

It is essential to embed product quality in the design process to win the global competition. Many components found in many products including automobiles and electronic devices are fabricated using sheet metal forming processes. Wrinkle and fracture are two types of defects frequently found in the sheet metal forming process. Reducing such defects is a hard problem as they are affected by many uncontrollable factors. Attempts to solve the problem based on traditional deterministic optimization theories are often led to failures. Furthermore, the wrinkle and fracture are conflicting defects in such a way that reducing one defect leads to increasing the other. Hence, it is a difficult task to reduce both of them at the same time. In this research, a new design method for reducing the rates of conflicting defects under uncontrollable factors is presented by using operating window and a sequential search procedure. A new SN ratio is proposed to overcome the problems of a traditional SN ratio used in the operating window technique. The method is applied to optimizing the robust design of a sheet metal forming process. To show the effectiveness of the proposed method, a comparison is made between the traditional and the proposed methods using simulation software, applied to a design of particular sheet metal forming process problem. The results show that the proposed method always gives a more robust design that is less sensitive to noises than the traditional method.

• The Journal of Engineering Research
• /
• v.2 no.1
• /
• pp.165-174
• /
• 1997

It is not possible to define the earth's interior because of it complicity. However, it can be interpreted directly and/ or indirectly. Geophysics is the subject of this study. To study the possibility of construction supervision by geophysical method, geophysical prospecting was performed and studied at the SamYang pumping well area in Cheju Island, where, although underground dam was constructed, the saline water invade the pumping well area. This study focuses on the construction supervision by electrical measurements. Two electric resistivity survey lines are installed in the pumping well site, and at each line electric survey was conducted at ebb and flow tides. To increase the data quality SP (self-potential) survey was also performed. As a result the geophysical exploration methods explained the defect of construction well, and It shows that geophysical probe can be a useful tool for the construction supervision.

• Korean Journal of Materials Research
• /
• v.11 no.9
• /
• pp.769-775
• /
• 2001

High quality PZT piezoelectric thin films were sputter- deposited on$ RuO_2$/$SiO_2$/Si substrates by using 2-step deposition method. As the first step, PZT seed layers were fabricated at a low temperature($475^{\circ}C$ ) to form a pure perovskite phase by reducing the volatility of Pb oxide. and then, as the second step, the PZT films were deposited at high temperatures ($530^{\circ}C$~$570^{\circ}C$) to reduce the defect density in the films. By this method, the pure perovskite phase was obtained at high deposition temperature range ($530^{\circ}C$~$570^{\circ}C$) and the superior electrical properties of PZT films were obtained on $RuO_2$substrate : 2Pr : 60$\mu$C/$\textrm{cm}^2$, $E_c: 60kV/cm, \;J_t: 10^{-6}A/cm^2\; at\; 250kV/cm$. The residual stress of PZT films fabricated by the 2-step deposition method was tensile and below 150MPa. It was attempted to control the residual stress in the PZT films by applying a negative bias to the substrate. As the amplitude of the substrate bias was increased, the residual tensile stress was slightly decreased, however, the ferroelectric properties of PZT films were degraded by ion bombardment.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.687-690
• /
• 2015

Forward collision warning systems(FCWS) and lane change assist systems(LCAS) need regions of interest for detecting lanes and objects as road regions. Watershed segmentation is effective algorithm that classify the road. That algorithm is split results appear differently depending on Watershed line with local minimum in the early part of the seed. If not road regions or vehicles combined the road's seed, It segment road with the others. For compensate the that defect, It has to adaptive change by road environment. The method is that image segmentate the several of regions of interest. Then It is set in a straight line that is detected in regions of interest. If It was detected cars on seed, seed is adjusted the location. And If It wasn't include the line, seed is adjusted the length for final decision the seed. We can detect the road region using the final seed that selected according to the road environment.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.114-114
• /
• 2008

반도체 device의 성능을 향상시키기 위하여 패턴은 더욱 더 고 집적화 되고 배선 또한 다층배선 구조를 가지게 되었으며 요구되는 선폭 또한 더욱 미세화 되어 CMP 공정이 도입되게 되었다. 이러한 CMP 공정에 사용되는 소모품으로는 크게 세 가지의 중요한 부분으로 나눌 수 있다. 그것은 slurry와 pad, conditioner이다. 그중에 pad conditioning 공정은 CMP 공정시 pad의 마모에 따라 감소하는 removal rate(RR)값을 회복시키기 위한 공정으로 마모된 pad의 표면을 활성화 시켜주는 중요한 공정이다. 하지만 pad conditioning 공정을 장시간 진행하게 되면 conditioner 표면에 오염물이 발생하게 되며, 오염물로 인하여 wafer표면에 scratch 및 defect을 발생시키는 원인이 될 수 있다. 이러한 문제점을 보완하기 위하여 conditioner의 표면을 변화시켜 공정중의 오염이 발생하지 않도록 하는 것이 중요하다. 본 논문에서는 oxide CMP 실험을 통하여 conditioner표면에 오염물이 발생함을 확인하였으며 energy dispersive spectroscopy(EDS) 분석을 통하여 주오염물의 성분이 oxide slurry중 silica임을 확인하였다. Conditioner의 표면을 소수성으로 만들기 위하여 self assembled monolayer(SAM) 방법을 이용하여 표면에 코팅을 하였으며, 소수성 박막이 코팅된 conditioner와 코팅되지 않은 conditioner의 비교 실험을 통하여 오염 정도를 비교하였다.

• Smart Structures and Systems
• /
• v.25 no.1
• /
• pp.23-35
• /
• 2020

It is important to take into account the thermal behavior in assessing the structural condition of bridges. An effective method of studying the temperature effect of long-span bridges is numerical simulation based on the solar radiation models. This study aims to develop a time-varying solar radiation model which can consider the real-time weather changes, such as a cloud cover. A statistical analysis of the long-term monitoring data is first performed, especially on the temperature data between the south and north anchors of the bridge, to confirm that temperature difference can be used to describe real-time weather changes. Second, a defect in the traditional solar radiation model is detected in the temperature field simulation, whereby the value of the turbidity coefficient t_u is subjective and cannot be used to describe the weather changes in real-time. Therefore, a new solar radiation model with modified turbidity coefficient γ is first established on the temperature difference between the south and north anchors. Third, the temperature data of several days are selected for model validation, with the results showing that the simulated temperature distribution is in good agreement with the measured temperature, while the calculated results by the traditional model had minor errors because the turbidity coefficient t_u is uncertainty. In addition, the vertical and transverse temperature gradient of a typical cross-section and the temperature distribution of the tower are also studied.