• Journal of Navigation and Port Research
• /
• v.32 no.3
• /
• pp.245-250
• /
• 2008

Recently the numerical prediction technique is applied to many fields, because numerical models are developed so much for last decades. The real-time ocean prediction system is one of them and is capable of providing the real-time marine information for users to promote the safety af maritime traffic and preservation of marine resources. The system is composed of observing system, data distribution system and modelling system. In this study authors develop the modelling system and show the results as preliminary study for establishing the real-time ocean prediction system in Busan port. The system test is performed only for M2 tidal modelling due to the lack qf observation data, thus a full-scale test is required in future if enough data are provided Also observing system and data distribution system will be constructed continuously in future, then service for real-time data for users will be initiated.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.6
• /
• pp.633-640
• /
• 2001

Statement of problem. Relatively low success rate of root analogue implant system was supposed to be due to the time duration between extraction and implant installation. The use of three-dimensional computer tomography and the reconstruction of objects using rapid prototyping methods would be helpful to shorten this time. Purpose. This aim of this study was to evaluate the application possibility of the 3-dimensional computer tomography and the rapid prototyping to root analogue implants. Material and methods. Ten single rooted teeth were prepared. Width and height of the teeth were measured by the marking points. This was followed by CT scanning, data conversion and rapid prototyping model fabrication. 2 methods were used; fused deposition modelling and stereolithography. Same width and height of this models were measured and compared to the original tooth. Results. Fused deposition modelling showed an enlarged width and reduced height. The stereolithography showed more exact data compared with the fused deposition modelling. Smaller standard deviation were recorded in the stereolithographic method. Overall width error from tooth to rapid prototyping was 7.15% in fused deposition modelling and 0.2% in stereolithography. Overall height showed the tendency of reducing dimensions. Conclusion. From the results of this study, stereolithography seems to be very predictable method of fabricating root analogue implant.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.6
• /
• pp.887-893
• /
• 2010

Modelling methods of 3 phase induction motors dependant on a lot of parameters give much drawbacks and difficulties when making engine room simulators due to computation burden and the time required for acquiring detailed technical data corresponding to actual induction motors. This paper suggests a practical method by a equivalent circuit with minimized parameters and some formulas to configure induction motors which requires only data on the name plates of motors, while it revealed satisfactory modelling performances on the resultant curves which are plotted for the torque, load current and power consume according to slip variation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.227-232
• /
• 2003

Usually, the thrust of a Linear Pulse Motor(LPM) is calculated by magnetic equivalent circuit modelling method. Analytical thrust deviation exists to calculating magnetic flux density by using Permeance Modelling Method, Finite Element Method, and Velocity Electric Motive Force Method. For calculating accuracy thrust by using these every method, the thrust is calculated and compared by Lorentz Force Method, Magnetic Coenergy Method, and Maxwell correspondence force Method. And that becomes important factor at the comparison of each capacity and parameter of motor. So this study wants to compare and analyze measurement data and calculating data of the static thrust of LPM. and then we can get more accuracy method, calculating the static thrust of LPM.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.10 no.4
• /
• pp.220-228
• /
• 2002

The cool-down performance after soaking is very important in an automotive air-conditioning system and is considered as a key design variable. Therefore, transient characteristics of each system component are essential to the preliminary design as well as steady-state performance. The objective of this study is to develop a computer simulation model and ostinato theoretically the transient performance of an automotive air-conditioning system. To do that, the mathematical modelling of each component, such as compressor, condenser, receiver/drier, expansion valve, and evaporator, is presented first of all. The basic balance equations about mass and energy are used in modelling. For detailed calculation, condenser and evaporator are divided into many sub-sections. Each sub-section is an elemental volume for modelling. In models of expansion valve and compressor, dynamic behaviors are not considered in this analysis, but the quasisteady state ones are just considered, such as the relation between mass flow rate and pressure drop in expansion device, polytropic process in compressor, etc. Also it is assumed that there are no heat loss and no pressure drop in discharge, liquid, and suction lines. The developed simulation model is validated by comparing with the laboratory test data of an automotive air-conditioning system. The overall time-tracing properties of each component agreed well with those of test data in this case.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2003.05a
• /
• pp.171-178
• /
• 2003

When oil is spilled at sea, the oil boom is commonly used to tackle the movement and spreading of oil in an early stage of oil spill combat. But, the retaining capability of oil boom is affected by various factors, such as water velocity, viscosity, and density of oil, water depth, oil volume and the length of boom draft. In this study, computer modeling was peformed to investigate how these factors influence the oil retaining process. The Fluent, most popular one of many CFD(computational fluid dynamics) programs is chosen for modelling and modelling results were verified using the empirical data. It is expected that results of this study will be useful data for oil boom designer and oil spill response commander.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 1998.11a
• /
• pp.295-300
• /
• 1998

Recently graphical modelling is being studied as a useful process analysis tool for exploratory causal analysis. Graphical modelling is a presentation method that uses graphs to describe statistical models of the structures of multivariate data. This paper describes an application of this graphical modeling with two cases from the automotive parts industry. One case is the unbalance problem of the pulley, an automotive generator part. There is multivariate data of the product from each of the processes which are connected in the series. By means of exploratory causal analysis between the variables using graphical modeling, the key processes which causes the variation of the final characteristics and their mechanism of the causal relationship have become clear. Another case is, also, the unbalanced problem of automotive starter parts which consists of many parts and is manufactured by complex machinery and assembling process. By means of the similar technique, the key processes are obtained easily and the results are reasonable from technical knowledge.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.10
• /
• pp.2446-2456
• /
• 1993

By virtue of progress of computer science, CAD/CAM technology has been developed greatly in each area. But the problems in the integration of CAD/CAM are not yet solved completely. The reason is that the exchange of data between CAD and CAM is difficult because the domains of design and manufacturing are different in nature. To solve this problem, a feature based modeller is developed in this study, which makes it possible to communicate between design and manufacturing through features. The modeller has feature, the concept of semi-bounded plane is introduced, and implemented as a B-rep sheet model using half-edge data structure. The features are then created on a part by local modification of the boundary on a part based on feature template information. This approach generalizes the modelling of features in a geometry model.

• Structural Engineering and Mechanics
• /
• v.33 no.5
• /
• pp.589-604
• /
• 2009

In the field of predicting structural safety and reliability the operating conditions play an essential role. Since the time and cost limitations are a significant factors in engineering it is important to predict the future operating conditions as close to the actual state as possible from small amount of available data. Because of the randomness of the environment the shape of measured load spectra can vary considerably and therefore simple distribution functions are frequently not sufficient for their modelling. Thus mixed distribution functions have to be used. In general their major weakness is the complicated calculation of unknown parameters. The scope of the paper is to investigate the load spectra growth for actual operating conditions and to investigate the modelling and extrapolation of load spectra with algorithm for mixed distribution estimation, REBMIX. The data obtained from the measurements of wheel forces and the braking moment on proving ground is used to generate load spectra.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.6 no.2
• /
• pp.25-30
• /
• 2006

The purpose of this study was to investigate how student felt the strengths and shortness of presentation methods for formation of interior spaces. For this study, the process of the interior architecture design class was divided into three stages: the programming. the design development, and the design completion. In the design development stage, students used presentation methods: hand sketch, scale model, computer modeling, and virtual realty. The strengths of hand sketch was that quick expression. Models provided three-dimensional feelings. Computer modelling provide realistic color and texture. Virtual reality provided three-dimensional immersion and real scale. It is effective that students collect brain storm images using quick hand sketch in the beginning of design development stage. After that, they compose interior spaces in study models with small scale. Watching the models, they design details of spaces by using hand sketch and computer modelling. Using virtual reality, they can check the scale and circulation. Finally, they complete computer modelling by texture mapping and check the final design in virtual reality.