• Bulletin of the Korean Space Science Society
• /
• 1993.10a
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• Journal of Chest Surgery
• /
• v.30 no.5
• /
• pp.471-478
• /
• 1997

Introduction: The use of rabbits as a cardiopulmonary bypass(CPB) animal model is extremely dif%cult mainly due to technical problems. On the other hand, deep hypothermic circulatory arrest(CA) is used to facilitate surgical repair in a variety of cardiac diseases. Although steroids are generally known to be effective in the treatment of cerebral edema, the protective effects of steroids on the brain during CA are not conclusively established. Objectives of this study are twofold: the establishment of CPB technique in rabbits and the evaluation of preventive effect of steroid on the development of brain edema during CA. Material '||'&'||' Methods: Fifteen New Zealan white rabbits(average body weight 3.5kg) were divided into three experimental groups; control CA group(n=5), CA with Trendelenberg position group(n=5), and CA with Trendelenberg position + steroid(methylprednisolone 30 mglkg) administration group(n=5). After anesthetic induction and tracheostomy, a median sternotomy was performed. An aortic cannula(3.3mm) and a venous ncannula(14 Fr) were inserted, respectively in the ascending aorta and the right atrium. The CPB circuit consisted of a roller pump and a bubble oxygenator. Priming volume of the circuit was approximately 450m1 with 120" 150ml of blood. CPB was initiated at a flow rate of 80~85ml/kg/min, Ten min after the start of CPB, CA was established with duration of 40min at $20^{\circ}C$ of rectal temperature. After CA, CPB was restarted with 20min period of rewarming. Ten min after weaning, the animal was sacrif;cod. One-to-2g portions of the following tissues were rapidly d:ssected and water contents were examined and compared among gr ups: brain, cervical spinal cord, kidney, duodenum, lung, heart, liver, spleen, pancreas. stomach. Statistical significances were analyzed by Kruskal-Wallis nonparametric test. Results: CPB with CA was successfully performed in all cases. Flow rate of 60-100 mlfkgfmin was able to be maintained throughout CPB. During CPB, no significant metabolic acidosis was detected and aortic pressure ranged between 35-55 mmHg. After weaning from CPB, all hearts resumed normal beating spontaneously. There were no statistically significant differences in the water contents of tissues including brain among the three experimental groups. Conclusion: These results indicate (1) CPB can be reliably administered in rabbits if proper technique is used, (2) the effect of steroid on the protection of brain edema related to Trendelenburg position during CA is not established within the scope of this experiment.

• Journal of Animal Science and Technology
• /
• v.47 no.6
• /
• pp.1009-1016
• /
• 2005

This study was carried out to investigate the effects of substituting NaCl by sodium citrate, potassium lactate and calcium ascorbate (40%) on the quality characteristics of emulsion-type sausages. The pH of emulsion-type sausage of the substitution NaCl with sodium citrate were higher than those of control and the other(P<0.05). The CIE L* value emulsion-type sausage of the substitution NaCl with sodium citrate were higher than those of control and the other(P<0.05). The CIE a* value emulsion-type sausage of the substitution NaCl with potassium lactate were higher than those of control and the other, but CIE b* value were lower(P<0.05). The hardness and gumminess of emulsion-type sausage of the substitution NaCl with sodium citrate were higher than those of control and the other. The Na content of emulsion-type sausage of substitution NaCl with calcium ascorbate were lower than those of control and the other, but Ca content were higher(P<0.05). The K and Fe content of emulsion-type sausage of the substitution NaCl with potassium lactate were higher than those of control and the other(P<0.05). The saltiness of emulsion-type sausage of the substitution NaCl with sodium citrate were higher than those of control and the other(P<0.05). The flavor of emulsion-type sausage of the substitution NaCl with calcium ascorbate were higher than those of control(P<0.05).

• Analytical Science and Technology
• /
• v.28 no.3
• /
• pp.182-186
• /
• 2015

In this study, the porous CuO/MnO₂ catalyst was prepared through the co-precipitation process from an aqueous solution of potassium permanganate (KMnO₄), manganese(II) acetate (Mn(CH₃COO)₂·4H₂O) and copper(II) acetate (Cu(CH₃COO)₂·H₂O). The phase change in MnO₂ was analyzed according to the reaction molar ratio of KMnO₄ to Mn(CH₃COO)₂. The reaction mole ratio of KMnO₄ to Mn(CH₃COO)₂·4H₂O was varied at 0.3:1, 0.6:1, and 1:1. The aqueous solution of Cu(CH₃COO)₂ was injected into a mixed solution of KMnO₄ and Mn(CH₃COO)₂ to 10~75 wt% relative to MnO₂. The Cu ion co-precipitates as CuO with MnO₂ in a highly dispersed state on MnO₂. The physicochemical property of the prepared CuO/MnO₂ was analyzed by using the TGA, DSC, XRD, SEM, and BET. The different phase types of MnO₂ were prepared according to the reaction mole ratio of KMnO₄ to Mn(CH₃COO)₂·4H₂O. The results confirmed that the porous CuO/MnO₂ catalyst with γ-phase MnO₂ was produced in the reaction mole ratio of KMnO₄ to Mn(CH₃COO)₂ as 0.6:1 at room temperature.

• Korean journal of applied entomology
• /
• v.47 no.3
• /
• pp.273-286
• /
• 2008

Road-map for the environmental friendly integrated pest management(IPM) of insect pests was drawn up on the strawberry vinyl-houses of farmer's field. Major insect pests were occurred Tetranychus urticae and Aphis gossypii during the strawberry plant seeding in the vinyl house and open field. Also, same insect pests were occurred in the vinyl house during harvesting season of strawberry. For the control of T. urticae and A. gossypii, Phytoseiulus persimilis and Aphidius colemani as natural enemies were input to the vinyl house, respectively. However, because these natural enemies could not control insect pest populations, acaricide and insecticide were sprayed. Then natural enemies were input again in the vinyl house. Natural enemies could not endure the intense cold and differences of temperature and relative humidity between day and night during strawberry harvesting season. So, their behavior and control activity of pests were more decrease than pests. Firstly, natural enemies are input in the vinyl house during the early breeding season of strawberry, secondly, acaricides and insecticide are sprayed for the control of mites and aphids, respectively, during the middle breeding season in the hard winter. Finally, natural enemies are re-input in the vinyl house during the middle and late breeding season.

• Korean Journal of Poultry Science
• /
• v.31 no.4
• /
• pp.245-253
• /
• 2004

This study was conducted to investigate the effects of dietary yeast culture containing rPST on growth performances and the characteristics of body compositions in broiler chickens. A total of 460 Ross male broiler chicks aged 2-day-old were fed one of five experimental diets; Control(devoid of all), TI (with $0.1\%$ antibiotics; chlorotetracycline), T2 (with $0.1\%$ rPST-yeast culture), T3 (with $0.2\%$ rPST-yeast culture) or T4 (with $0.2\%$ SC yeast culture) for 6 weeks. Feed consumption and body weights were measured weekly. At week 5 of the experiment, 10 chicks were randomly selected and sacrificed. The relative weights of each organ and the chemical composition of edible meat were measured. The enzyme activity, total cholesterol, Ca and P were also determined. Tibial weight, bone strength and chemical composition were investigated. There were no significant differences in feed intake and feed conversion ratios among the treatments throughout the experimental period. Body weight gains tended to be increased by feeding of diets containing rPST-yeast culture. The relative weight of breast muscle in T3 group was significantly higher than that of the control (P<0.05). The moisture contents of breast meat in groups fed diets containing rPST-yeast culture or SC yeast culture were significantly increased as compared with those of the control and n. However, the contents of crude protein and ether extract were not affected by feeding of rPST-yeast culture. There were no significant differences in GOT, total cholesterol, Ca and P. The relative weight and strength and proximal composition of the tibia were also not affected by dietary treatments. These results indicated that dietary rPST-yeast culture may be a valuable alternative for optimizing growth performances, particularly for improving the yield of breast muscle.

• Journal of Animal Science and Technology
• /
• v.44 no.4
• /
• pp.391-398
• /
• 2002

This study was conducted to determine the polymorphism of transferrin exons 13, 15 and 16 by Single-Strand Conformation Polymorphism(SSCP) analysis and to compare their genotypes of Cheju horse Group I (Cheju Institute), Cheju horse Group II (farms), and Thoroughbred (KRA). SSCP of transferrin exon 13, 15, and 16 showed two (A, B), three (A, B, C) and three (A, B, C) codominant alleles, respectively. The Group I and Thoroughbred showed the similar frequencies of allele A and B in transferrin exon 13, but only allele A was observed in Group Ⅱ. In transferrin exons 15 and 16, the frequencies of each allele were different in each Groups. The multiple allele frequencies in exons 15 and 16 suggested that the genotyping of this locus could be used to identify an individual and to test the parentage of offspring. The probability for parentage exclusion were 0.46 and 0.374 for exons 15 and 16 for Cheju horse Group I. Among the 13 combined genotypes of exons 13, 15 and 16, the genotype AA-AB-AB (0.372) is the most common in Cheju horse Group I, but genotype AA-AA-AA is common in the Cheju horse Group II (0.366) and Thoroughbred (0.767). The present study showed two new SNP, which was at the cDNA position 1626 (A/G) in B allele of the exon 13 and 2075 (C/T) in C allele of the exon 16 resulting in amino acid change (Threonine $\longrightarrow$ Methionine). Result showed that polymorphism of exons 13, 15 and 16 in Cheju horses was as high as in Thoroughbred and there was a differences of transferrin allele frequencies in Cheju horses.

• Journal of Embryo Transfer
• /
• v.19 no.3
• /
• pp.219-227
• /
• 2004

This study was conducted to develop a serum-free, defined medium of IVM of pig oocytes. The TCM-199 with supplemented with polyvinylalcohol(PVA), polyvinylpyrrollidone(PVP) and porcine follicular fluid(pFF) were used as basal medium. The effects of the these additives on the rates of maturity and development under in-vitro fertilization and in vitro culture were examined and subsequently considered on the possibilities be sustituted for the bovine serum albumin(BSA). Maturation rate of pig oocytes in IVM media containing PVA(82.4％), pFF(89.4％) and BSA(90.0％) were significantly higher(P<0.05) than that of PVP(78.6％). Cleavage rate after IVF of PVP(64％) was significantly lower(P<0.05) than these of PVA(73％), pFF(77％) and BSA(73％) supplements. in vitro development rates to morulae and blastocyst on PVP(54％) were also significantly lower(P<0.05) than these of the supplements of PVA(63％), pFF(69％) and BSA(65％). In comparison of maturation and fertilization rates of pig oocytes in each supplements, the maturity rates of PVA(82.4％), pFF(89.4％) and BSA(90.0％) were significantly lower(P<0.05) than that of PVP(72.4％) and while, the fertilization rates of pFF(87.1％) and BSA(89.1％) were significantly higher(P<0.05) than these of PVA(78.0％) and PVP(70.6％). It may be concluded that PVA and pFF can be substituted far BSA in medium for culturing pig oocytes; however, it may be considered that PVP were limited to for BSA in the in vitro culture of the embryos.

• Asian-Australasian Journal of Animal Sciences
• /
• v.14 no.10
• /
• pp.1450-1459
• /
• 2001

These experiments were conducted to investigate the effects of different feeding and processing methods of diets on performance, morphological changes in the small intestine and nutrient digestibility of growing-finishing pigs. One-hundred fifty growing pigs ($Yorkshire{\times}Landrace{\times}Duroc$; initial body weight of $23.33{\pm}0.75kg$) and one-hundred twenty finishing pigs ($Yorkshire{\times}Landrace{\times}Duroc$; initial body weight of $59.22{\pm}0.56kg$) were used in Exp. 1 and Exp. 2, respectively. Pigs were grouped on the basis of body weight and gender, and randomly allotted into 6 different treatments with 5 replications in each treatment in a $2{\times}3$ factorial arrangement. Treatments were 1) dry feeding with a mash diet (DM), 2) dry feeding with a pelleted diet (DP), 3) dry feeding with an expanded crumble diet (DEC), 4) dry/wet feeding with a mash diet (WM), 5) dry/wet feeding with a pelleted diet (WP), and 6) dry/wet feeding with an expanded crumble diet (WEC). In Exp. 1 (growing phase), there was no significant difference in average daily gain (ADG) and average daily feed intake (ADFI) among treatments during the entire experimental period, but feed conversion ratio (FCR) was significantly (p<0.05) improved in pigs fed pelleted diets regardless of feeding method. FCR was best in pigs fed a DP diet and worst in pigs fed a WM diet. Pigs fed a pelleted diet showed a 6.2% or 4.0% improvement in FCR compared with those fed a mash diet or an expanded crumble diet. Water disappearance was not significantly affected by dry/wet feeding or feed processing. Significant differences in villus height were not found among treatments, but villus height tended to be improved by dry/wet feeding. Dry/wet feeding or feed processing did not affect crypt depth. Digestibilities of calcium and phosphorus were significantly (p<0.05) improved in pigs fed an expanded crumble diet compared with pigs fed mash diets. Especially, pigs fed a WEC diet digested 8.1% more P than those fed a DM diet. Feed cost per kg weight gain (FCG) tended to be increased by dry/wet feeding rather than dry feeding. In Exp. 2 (finishing phase), ADG and ADFI were not significantly different among treatments, but a significant difference in FCR was found among feed processing forms. The best FCR was obtained in pigs fed a pelleted diet. Pigs fed a DP diet showed a 11.3% improvement compared with those fed a DEC diet. Water disappearance was significantly (p=0.0408) decreased by feeding the mash diet. However, water disappearance was not affected by dry/wet feeding during the finishing period. The villus height and crypt depth were not significantly different among treatments. However, crypt depth tended to be decreased by dry/wet feeding at the mid part of the small intestine. Fat digestibility was improved by dry feeding rather than dry/wet feeding, and was improved by 4.8% by feeding pellet diets compared with expanded crumble diets. Except for carcass grade, carcass characteristics were not significantly (p<0.05) different among treatments. Carcass grade was the best in pigs fed a WP diet. Feed cost per kg weight gain (FCG) was significantly decreased in pigs fed a pelleted diet compared with those fed an expanded crumble diet, and tended to be decreased by dry/wet feeding. In conclusion, these studies suggest that feeding the pelleted diet to growing-finishing pigs can be beneficial in terms of FCR and production cost. Dry/wet feeding can be helpful for the maintenance of villus height, but may not be reflected in improved growth performance or reduction of production costs.

• Journal of Intelligence and Information Systems
• /
• v.17 no.1
• /
• pp.53-69
• /
• 2011

Vision and voice-based technologies are commonly utilized for human-robot interaction. But it is widely recognized that the performance of vision and voice-based interaction systems is deteriorated by a large margin in the real-world situations due to environmental and user variances. Human users need to be very cooperative to get reasonable performance, which significantly limits the usability of the vision and voice-based human-robot interaction technologies. As a result, touch screens are still the major medium of human-robot interaction for the real-world applications. To empower the usability of robots for various services, alternative interaction technologies should be developed to complement the problems of vision and voice-based technologies. In this paper, we propose the use of accelerometer-based gesture interface as one of the alternative technologies, because accelerometers are effective in detecting the movements of human body, while their performance is not limited by environmental contexts such as lighting conditions or camera's field-of-view. Moreover, accelerometers are widely available nowadays in many mobile devices. We tackle the problem of classifying acceleration signal patterns of 26 English alphabets, which is one of the essential repertoires for the realization of education services based on robots. Recognizing 26 English handwriting patterns based on accelerometers is a very difficult task to take over because of its large scale of pattern classes and the complexity of each pattern. The most difficult problem that has been undertaken which is similar to our problem was recognizing acceleration signal patterns of 10 handwritten digits. Most previous studies dealt with pattern sets of 8~10 simple and easily distinguishable gestures that are useful for controlling home appliances, computer applications, robots etc. Good features are essential for the success of pattern recognition. To promote the discriminative power upon complex English alphabet patterns, we extracted 'motion trajectories' out of input acceleration signal and used them as the main feature. Investigative experiments showed that classifiers based on trajectory performed 3%~5% better than those with raw features e.g. acceleration signal itself or statistical figures. To minimize the distortion of trajectories, we applied a simple but effective set of smoothing filters and band-pass filters. It is well known that acceleration patterns for the same gesture is very different among different performers. To tackle the problem, online incremental learning is applied for our system to make it adaptive to the users' distinctive motion properties. Our system is based on instance-based learning (IBL) where each training sample is memorized as a reference pattern. Brute-force incremental learning in IBL continuously accumulates reference patterns, which is a problem because it not only slows down the classification but also downgrades the recall performance. Regarding the latter phenomenon, we observed a tendency that as the number of reference patterns grows, some reference patterns contribute more to the false positive classification. Thus, we devised an algorithm for optimizing the reference pattern set based on the positive and negative contribution of each reference pattern. The algorithm is performed periodically to remove reference patterns that have a very low positive contribution or a high negative contribution. Experiments were performed on 6500 gesture patterns collected from 50 adults of 30~50 years old. Each alphabet was performed 5 times per participant using $Nintendo{(R)}$ $Wii^{TM}$ remote. Acceleration signal was sampled in 100hz on 3 axes. Mean recall rate for all the alphabets was 95.48%. Some alphabets recorded very low recall rate and exhibited very high pairwise confusion rate. Major confusion pairs are D(88%) and P(74%), I(81%) and U(75%), N(88%) and W(100%). Though W was recalled perfectly, it contributed much to the false positive classification of N. By comparison with major previous results from VTT (96% for 8 control gestures), CMU (97% for 10 control gestures) and Samsung Electronics(97% for 10 digits and a control gesture), we could find that the performance of our system is superior regarding the number of pattern classes and the complexity of patterns. Using our gesture interaction system, we conducted 2 case studies of robot-based edutainment services. The services were implemented on various robot platforms and mobile devices including $iPhone^{TM}$. The participating children exhibited improved concentration and active reaction on the service with our gesture interface. To prove the effectiveness of our gesture interface, a test was taken by the children after experiencing an English teaching service. The test result showed that those who played with the gesture interface-based robot content marked 10% better score than those with conventional teaching. We conclude that the accelerometer-based gesture interface is a promising technology for flourishing real-world robot-based services and content by complementing the limits of today's conventional interfaces e.g. touch screen, vision and voice.