• ETRI Journal
• /
• v.33 no.1
• /
• pp.125-127
• /
• 2011

This letter presents a new type of resonator, namely, the split quarterwave microstrip resonator (SQMR), to improve the poor harmonic suppression and low Q-factors in conventional quarterwave microstrip resonators. An oscillator incorporating the proposed SQMR is designed, fabricated, and tested to demonstrate that, not only the second harmonic suppression, but also the phase noise of the oscillator can be improved. The oscillator with the SQMR shows improved second harmonic suppression of -74.59 dBc and phase noise figure of merit of -169.77 dBc/Hz at 1 MHz offset.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.419-423
• /
• 2001

It is important to know the mechanical properties of the materials under dynamic load. The mechanical properties of most materials are influenced to some extent by strain rate. One of the reliable test device for determining the mechanical properties of materials at high strain rate is Split Hopkinson Pressure bar. In this paper, we conducted the mechanical properties test for the aluminium alloy 6063 and 6061 using the SHPB device.

• Advanced Composite Materials
• /
• v.16 no.2
• /
• pp.167-180
• /
• 2007

The tensile strength of unidirectional carbon fiber reinforced plastics under a high strain rate was experimentally investigated. A high-strain-rate test was performed using the tension-type split Hopkinson bar technique. In order to obtain the tensile stress-strain relations, a special fixture was used for the impact tensile specimen. The experimental results demonstrated that the tensile modulus and strength in the longitudinal direction are independent of the strain rate. In contrast, the tensile properties in the transverse direction and the shear properties increase with the strain rate. Moreover, it was observed that the strain-rate dependence of the shear strength is much stronger than that of the transverse strength. The tensile strength of off-axis specimens was measured using an oblique tab, and the experimental results were compared with the tensile strength predicted based on the Tsai-Hill failure criterion. It was concluded that the tensile strength can be characterized quite well using the above failure criterion under dynamic loading conditions.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1819-1824
• /
• 2004

The common method to improve heat transfer in Nuclear fuel rod bundle is install a mixing vane in space grid. The previous split mixing vane is guides cooling water to swirl flow in sub-channel of fuel assembly. But, this swirl flow decade rapidly after mixing vane and the effect of enhancing the heat transfer vanish behind this short region. The large scale secondary vortex flow was generated by rearranging the inclined angle direction of mixing vanes to the coordinated directions. This LSVF mixing vanes generate the most strong secondary flow vortices which maintain about 35 $D_H$ after the spacer grid and the streamwise vorticity in subchannel with LSVF mixing vane sustain two times more than that in subchannel with split mixing vane. The turbulent kinetic energy and the Reynolds stresses generated by the mixing vanes have nearly same scales but maintain twice more than previous type.

• Applied Biological Chemistry
• /
• v.20 no.1
• /
• pp.147-155
• /
• 1977

In this experiment, we expected yield increase depending on the control of ineffective tiller, heightening of effective tillering ratio and continuous supply of nitrogen until later growth stage of rice plant by deep layer split application. Treats were applied at Tongil and Jinheung variety, clayey loam and sandy loam soil, and drained and non-drained condition. Nitrogenous fertilizer application wab adopted as liquefied(50%) and lumped (50% and 80%) fertilizer at 12cm depth of soil before 35 days of rice heading time against the standard soil surface application. The results are summarized as follaw. 1. a. Jinheung showed great variant width of tiller numbers per rice plant growth stage, and low effective tillering ratio at soil surface dressing. But in the case of deep layer split application, the number of tiller increased normally, and effective tillering ratio was high. b. At Tonsil, the width of increase and decrease range of effective tiller number between soil surface dressing and deep layer split application was not so high as Jinheung. Deep layer split application of 80% lumped fertilizer showed maximum effective tillering ratio ($83%{\sim}93%$). C. In the case of Jinheung, it was supposed that deep layer split application of 80% lumped fertilizer was excessive nitrogen quantity. d. Effective tillering ratio was higher than Tonsil at Jinheung. 2. The number of grains per hill was increased by the deep layer split application, but the ripening ratio was decreased inversely with the increase of total grain number. 3. Length of top leaves was elongated at Jinheung by deep layer split application. It showed significant correlation between top leaves length and grain yield. 4. Deep layer split application inclosed N content of harvested straw. Yield and N content of straw showed possitive correlation. 5. The ratio of unhulled grain yield per straw weight was increased by deep layer splication. This ratio was higher at Jinheung than Tonsil. 6. Grain yield was appeared in order of 80% lumped fertilizer>50% lumped fertilizer>50% liquefied fertilizer>surface dressing by the deep layer split application. The yield increasing factors were the increasing of effective tillering ratio, number of panicles per hill and number of ripening grains per hill. 7. Grain yield was increased at Tongil in sandy loam soil and at Jinheung in clayey loam soil by deep layer split application. 8. The grain yield was increased at drained conditions of clayey loam soil and non-drained conditions of sandy loam soil. But in the case of 80% lumped fertilizer of deep layer split application at the sandy loam soil, the yield was not increased at non-drained conditions. 9. The effect of yield increase by deep layer split application comparing with the surface dressing was higher at Tonsil than ginheung, in spite of low ripening ratio of Tonsil caused by low temperature at heading and harvesting time.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2007.05a
• /
• pp.17.2-17.2
• /
• 2007

• The KIPS Transactions:PartD
• /
• v.10D no.2
• /
• pp.195-210
• /
• 2003

In this paper, we propose an enhanced concurrency control algorithm that maximizes the concurrency of multi-dimensional index structures. The factors that deteriorate the concurrency of index structures are node splits and minimum bounding region (MBR) updates in multi-dimensional index structures. The proposed concurrency control algorithm introduces PLC(Partial Lock Coupling) technique to avoid lock coupling during MBR updates. Also, a new MBR update method that allows searchers to access nodes where MBR updates are being performed is proposed. To reduce the performance degradation by node splits the proposed algorithm holds exclusive latches not during whole split time but only during physical node split time that occupies the small part of a whole split process. For performance evaluation, we implement the proposed concurrency control algorithm and one of the existing link technique-based algorithms on MIDAS-3 that is a storage system of a BADA-4 DBMS. We show through various experiments that our proposed algorithm outperforms the existing algorithm in terms of throughput and response time. Also, we propose a recovery protocol for our proposed concurrency control algorithm. The recovery protocol is designed to assure high concurrency and fast recovery.

• Archives of Craniofacial Surgery
• /
• v.17 no.4
• /
• pp.211-217
• /
• 2016

Background: Nonsyndromic craniosynostosis is a relatively common craniofacial anomaly and various techniques were introduced to achieve its operative goals. Authors found that by using smaller bone fragments than that used in conventional cranioplasty, sufficiently rigid bone union and effective regeneration capacity could be achieved with better postoperative outcome, only if their stable fixation was ensured. Methods: Through bicoronal incisional approach, involved synostotic cranial bone together with its surrounding areas were removed. The resected bone flap was split into as many pieces as possible. The extent of this 'multi-split osteotomy' depends on the degree of dysmorphology, expectative volume increment after surgery and probable dead space caused by bony gap between bone segments. Rigid interosseous fixation was performed with variable types of absorbable plate and screw. In all cases, the pre-operational three-dimensional computed tomography (3D CT) was checked and brain CT was taken immediately after the surgery. Also about 12 months after the operation, 3D CT was checked again to see postoperative morphology improvement, bone union, regeneration and intracranial volume change. Results: The bony gaps seen in the immediate postoperative brain CT were all improved as seen in the 3D CT after 12 months from the surgery. No small bone fragment resorption was observed. Brain volume increase was found to be made gradually, leaving no case of remaining epidural dead space. Conclusion: We conclude that it is meaningful in presenting a new possibility to be applied to not only nonsyndromic craniosynostosis but also other reconstructive cranial vault surgeries.

• Korean Journal of Optics and Photonics
• /
• v.3 no.4
• /
• pp.227-233
• /
• 1992

The simulation code was developed for the development of the split-disk geometry glass amplifier, which could design the laser apparatus and analyze the properties of the laser system. The flashlamp emission energy at the short wavelength region must be reduced, while maintaining a current density between 2000 and 4000 A/$\textrm{cm}^{2}$, in order to reduce the thermal loading in the laser glass and to raise the coupling efficiency between the emission spectrum of the flashlamps and the absorption spectrum of the laser glass. By cutting the laser glass into three equal pieces, the temperature rise in the laser glass dropped by 70% due to the efficient removal of the heat in the laser glass. It was found that the $Nd^{3+}$ doping rate of each laser glass should be properly selected and the optimum value of the product of the absorption coefficient $\alpha$ and the thickness d of the laser glass is about 0.26 in the split-disk geometry.

• 한국약용작물학회:학술대회논문집
• /
• 2012.05a
• /
• pp.81-82
• /
• 2012