• Geomechanics and Engineering
• /
• v.20 no.5
• /
• pp.385-397
• /
• 2020

This paper presents an application of artificial neural networks (ANNs) in settlement prediction of a foundation on sandy soil. In order to train the ANN model, a wide experimental database about settlement of foundations acquired from available literatures was collected. The data used in the ANNs model were arranged using the following five-input parameters that covered both geometrical foundation and sandy soil properties: breadth of foundation B, length to width L/B, embedment ratio D_f/B, foundation net applied pressure q_net, and average SPT blow count N. The backpropagation algorithm was implemented to develop an explicit predicting formulation. The settlement results are compared with the results of previous studies. The accuracy of the proposed formula proves that the ANNs method has a huge potential for predicting the settlement of foundations on sandy soils.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.739-742
• /
• 2002

This paper is to see the availability of electrical signatures as a means for evaluating performance of MOVs which are extensively used in safety-related systems in nuclear plants. To estimate motor torque, two methods such as d-q frame conversion and air-gap method are suggested and estimated results are compared with measured values. The error between measured and estimated torques is within acceptable error bound with below $1\%$ under varied load. Frequency domain analysis of calculated torque has been done as well. It is shown that monitoring of peak frequency could give useful clues to detect anomalies of MOV.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.431-434
• /
• 2002

This paper presents an implementation of direct torque control(DTC) of Reluctance Synchronous Motor(RSM) with an efficiency optimization using the 32bit DSP TMS320C31. The influence of iron loss can not neglected as high speed and precision torque control of RSM, so the optimal current ration between torque current and exiting current analytically derived to drive RSM at maximum efficiency For RSM, torque dynamics can be maintained even with controlling the flux level because the generated torque is direct]y proportional to the stator current. The experimental results for an RSM are presented to validate the applicability of the proposed method. The developed control system is shown high efficiency features with 1.0Kw RSM having 2.57 ratio of d/q reluctance.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.502-505
• /
• 1998

In this paper, the new vector control scheme of BLDCM producing loss-minimized ripple-free torque based on the d-q-Ο reference frame is presented including 3 phase unbalanced condition. The optimized phase current wave-forms that are obtained by the proposed method can be a reference values and the motor winding currents are forced to track it by delta modulation technique. As a results, it can be shown that the proposed work provides a simple and clear way to obtain an optimal motor excitation current.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.234-238
• /
• 1998

Parameter estimation of induction motor for vector control presented in this paper can be easily implemented and applied to inverters in the industrial field, because it needs no additional hardware such as voltage sensor and measuring equipment. At first, the stator resistance including switching loss of inverter is measured by simple voltage-current equation. Next, in pre-magnetization of machine by imposing the d-axis constant field-current, q-axis torque current is forced to the machine until its speed feedback reachs to pre-defined level of speed limit. At this time, we can measure the rotor time-constant by decreasing the distorted output-voltage of inverter. At last, stator inductance, transient inductance, and moment of inertia can be measured by the relationship of output voltage, output torque and speed feedback. The validity and usufulness of this method is verified by experimental results.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.817-825
• /
• 2018

In this paper, a current hysteresis control with good decoupling properties for doubly-fed brushless induction machines (BDFIMs) has been proposed based on a generalized vector model. The independent control of the reactive power and speed for BDFIMs has been achieved by controlling the d-axis and the q-axis current of the control windings (CW). The proposed vector control method has been developed for the power winding (PW) flux frame. Experimental verification of a type Y180M-4 BDFIM prototype with 1/4 pole-pairs has been presented. Evidence of its good performance has been shown through experimental results.

• Proceedings of the KIEE Conference
• /
• 1997.07c
• /
• pp.848-850
• /
• 1997

A control method of UPFC (Unified Power Flow Controller) to reduce low frequency oscillation is proposed. UPFC is modelled by voltage source, which magnitude and phase angle can be controlled. Because there needs some time to change to desired value, d-axis voltage and Q-axis voltage is modeled by 1st order delay. LQG(Linear Quadratic Gaussian) is used. It is shown that low frequency can be damped by control of UPFC effectively.

• Proceedings of the KIEE Conference
• /
• 1997.07b
• /
• pp.446-448
• /
• 1997

The aim of this paper is to introduce a method designing the optimal model following boiler-turbine control system using genetic algorithms. This boiler-turbine control system is designed by applying genetic algorithms with reference model to the optimal determination of weighting matrices Q, R that are given by LQ regulator problem. These weighting matrices are optimized simultaneously in the search domain selected adequately. The effectiveness of this boiler-turbine control system is verified by computer simulation.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.437-440
• /
• 2009

In this paper, an aluminum ring forging process of manufacturing an optimized perform for a hot forging process is simulated using AFDEX 3D, a general-purpose metal forming simulator based on rigid-thermoviscoplastic finite element method. Non-isothermal analysis is carried out and the predictions are compared with the experiments in terms of dimensional accuracy. It was shown that the predictions are in good agreement with the experiments.

• Journal of Drive and Control
• /
• v.9 no.4
• /
• pp.42-51
• /
• 2012

Variable displacement vane-type oil pumps represent one of the most innovative pump types for industrial applications, especially for engine lubrication systems. This paper deals with a modeling method for theoretical flow rate investigation of a typical variable displacement vane-type oil pump. This theoretical model is based on the pump geometric design and dynamic analyses. It can be considered as mandatory steps for a deeper understanding of the pump operation as well as for effectively implementing the pump control mechanisms to satisfy the urgent demands of engine lubrication systems. The developed pump model is finally illustrated by numerical simulations.