• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.197-200
• /
• 2001

In this letter, we report on the investigation of Ni/Si/Ni Ohmic contacts to n-type 4H-SiC. Ohmic contacts have been formed by a vacuum annealing and $N_2$ gas ambient annealing method at $950^{\circ}C$ for 10 min. The specific contact resistivity ( $\rho_{c}$ ), sheet resistance($R_s$), contact resistance($R_c$), transfer length($L_T$) were calculated from resistance($R_T$) versus contact spacing(d) measurements obtained from 10 TLM(transmission line method) structures. The resulting average values of vacuum annealing sample were $\rho_{c}=3.8{\times}10^{-5}\Omega cm^{3}$, $R_{c}=4.9{\Omega}$, $R_{T}=9.8{\Omega}$ and $L_{T}=15.5{\mu}m$, resulting average values of another sample were $\rho_{c}=2.29{\times}10^{-4}\Omega cm^{3}$, $R_{c}=12.9{\Omega}$ and $R_{T}=25.8{\Omega}$. The physical properties of contacts were examined using X-Ray Diffraction and Auger analysis, there was a uniform intermixing of the Si and Ni, migration of Ni into the SiC.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.36 no.4
• /
• pp.267-273
• /
• 2000

The tooth selectivity of the dredge for catching venus clam (Gomphina melanaegis) was described in which the teeth penetrated the bottom and lifted the shell into the bag. Some factors affecting the selection action of the teeth of the dredge were analyzed related to shell length and shell height. The retention probability of venus clam not sifting through the gaps between the teeth was calculated for various shell lengths and was fitted to two parameter logistic selection curve. The formula obtained is as follows: $P= \frac{1}{1+exp[8.24](\frac{d}{L_1}-0.649)}$, where d is distance between teeth and $L_1$ is a shell length. For biological minimum size(25mm) of venus clam to be catchability 50% the distance between teeth was estimated 16.2mm from the logistic curve. Therefore it is desirable to extend that current spacing between teeth from 12mm to 16mm for the venus clam dredge. That space increasing enables fuel oil of vessel to drag a dredge to be reduced and also man power to sift through sifter smaller venus clams on boards to be reduced.

• Korean Journal of Optics and Photonics
• /
• v.13 no.6
• /
• pp.461-466
• /
• 2002

Fiber-optic comb filters using a side-polished fiber coupler are proposed as multi-channel isolation filters on wavelength division multiplexing systems. We have demonstrated that the coupling efficiency between two waveguides is improved by the intermediate coupling layer in spite of the decrease of the optical power transfer between two waveguides due to the high-order modes of the overlay waveguide coupled with the side-polished single-mode fiber. When LiNbO$_3$with a 200-${\mu}{\textrm}{m}$-thickness was applied as a planar-overlay-waveguide, the comb filtering characteristics with a 4 nm-channel-spacing were achieved and the maximum power coupling occurred at the 1-${\mu}{\textrm}{m}$-thickness and the refractive index in range 1.52 to 1.53 of an intermediate coupling layer. If the intermediate coupling layer is optimized, an extinction ratio with more than 20 dB can be obtained. These experimental results are in good agreement with the BPM simulation.

• Korean Journal of Optics and Photonics
• /
• v.16 no.3
• /
• pp.266-274
• /
• 2005

We have designed photonic crystal based bandpass filters whose characteristics are suitable for WDM communication system. The filters consist of coupled point defect resonators in two-dimensional photonic crystal. The frequency response of coupled resonators has been analyzed by the coupling of modes in time, from which the design parameters for the coupled resonator filters have been extracted. For the appropriate choice of the design parameters, each resonator is treated as a lumped L-C resonance circuit, and from the analogy between the equivalent circuit and the standard L-C filter circuits, the design parameters are simply determined from the table for general filter circuit design. Based on the determined design parameters, a photonic crystal based filter has been designed and its performance has been calculated using the finite-difference time-domain method. The designed filter shows a pass band of 50GHz and 0.5 dB in-band ripple, which is suitable for typical WDM communication systems with 100GHz channel spacing.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.615-619
• /
• 2012

Recently, ultrafine grained (ufg, typically 100 > d > 500 nm) Ti-Fe eutectic materials have been highlighted due to their extraordinarily high strength and good abrasion resistance compared to conventional coarse grained (cg, d > $1{\mu}m$) materials. However, these materials exhibit limited plastic strain and toughness during room temperature deformation due to highly localized shear strain. Several approaches have been extensively studied to overcome such drawbacks, such as the addition of minor elements (Sn, Nb, Co, etc.). In this paper, we have investigated the influence of the addition of Gd and Y contents (0.3-1.0 at.%) into the binary Ti-Fe eutectic alloy. Gd and Y are chosen due to their immiscibility with Ti. Microstructural investigation reveals that the Gd phase forms in the eutectic matrix and the Gd phase size increases with increasing Gd content. The improvement of the mechanical properties is possibly correlated to the precipitation hardening. On the other hand, in the case of Ti-Fe-Y alloys, with increasing Y contents, primary phases form and lamellar spacing increases compared to the case of the eutectic alloy. Investigation of the mechanical properties reveals that the plasticity of the Ti-Fe-Y alloys is gradually improved, without a reduction of strength. These results suggest that the enhancement of the mechanical properties is closely related to the formation of the primary phase.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.917-920
• /
• 2008

ECC is a special kind of high performance cementititous composite which exhibits typically more than 2% tensile strain capacity by bridging microcracks at a crack section. Therefore, micromechanics should be adopted to obtain multiple cracking and strain hardening behavior. This paper propose a linear elastic analysis method to simulate the multiple cracking and strain hardening behavior of ECC. In an analysis, the stress-crack opening relation modified considering the orientation of fibers and the number of effective fibers is adopted. Furthermore, to account for uncertainty of materials and interface between materials, the randomness is assigned to the tensile strength(${\sigma}_{fci}$), elastic modulus($E_{ci}$), peak bridging stress(${\sigma}_{Bi}$) and crack opening at peak bridging stress(${\delta}_{Bi}$), initial stress at a crack section due to chemical bonding, (${\sigma}_{0i}$), and crack spacing(${\alpha}_cX_d$). Test results shows the number of cracking and stiffness of cracked section are important parameters and strain hardening behavior and maximum strain capacity can be simulated using the proposed method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.35-41
• /
• 1997

A series-fed microstrip array antenna of beamwidth $10^{\circ}$, squint angle $80^{\circ}$ and SLL -15 dB below is designed. Series-fed arrays are formed by interconnecting all the elements by high-impedance transmission lines and feeding the power at the first element and it is a traveling-wave antenna which is terminated with a matched load. Radiation patterns and impedance matching of the antenna are analyzed by Ensemble 4.0, which is a popular software package for designing printed antennas and arrays. The squint angle of beam can be controlled by the spacing between the elements. The major advantages of series-fed array antennas are that feed arangement is compact and the losses associated with the feeding network are less than those of a corporate feed type. The antennas are fabricated on the RT/Duroid Laminates of 62 mil thickness. The experimental results are very close to the specifications to be designed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.303-310
• /
• 2002

Overbreak occurred inevitably in a tunnel excavation, Is the main factor for increasing cost and time in tunnel projects. Furthermore the damage to the remained rock mass related to the overbreak can give rise to a serious safety problem in tunnels. As a rule of thumb, causes for the overbreak are inaccuracy in drilling, the wrong design of blasting and selection of explosives, and heterogeneity in rock mass. Specially, the geological features of the rock mass around periphery of an excavation are very important factors, so a lot of researches have been conducted to describe these phenomena. But the quantitative geological classification of the rock mass for the overbreak and the method for decreasing the amount of the overbreak have not been established. Besides, the technical improvement of the charge method is requested as explosives for the smooth blasting have not functioned efficiently. In this study, the working face around periphery of an excavation has been continuously sectionalized to 5∼6 parts, and the new Blastability Index for the overbreak based on 6 factors of RMD(Rock Mass Description), UCS(Uniaxial Compressive Strength) JPS(Joint Plane Spacing), JPO(Joint Plane Orientation), JPA(Joint Plane Aperture) and FM(Filling Material) is proposed to classify sections of the working face. On the basis of this classification, the distance between contour holes and the charging density are determined to minimize the overbreak. For controlling the charging density and improving the function of explosives, the New Deck Charge(N.D.C) method utilizing the deck charge method and detonation transmission in hole has been developed.

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.945-948
• /
• 2008

Nanocomposite materials provides efficient reinforcement, thermal endurance, and many other advantages depending on the additives used, with applications in the aerospace, automotive, and biomedical industries. Here, epoxy based nanocomposites were synthesized in the presence of Cloisite 15A and characterized with TEM, XRD, TGA, and DMA. To determine the effect of the clay d-spacing, Cloisite 20A was also used to synthesize the nanocompostes. In addition to the traditional hot plate method, an ultrasonicator was used to investigate the effect of different types of mixing on the properties of the nanocomposite; no significant effect was found. An examination of the nanocomposite morphology revealed that all the nanocomposites synthesized yielded an intercalated structure. When 5 wt% of Cloisite 15A was used with 20 min sonication time, the storage modulus increased 10% over the neat(no clay) nanocomposite. In general, the presence of Cloisite 15A produced a better storage modulus than Cloisite 20A.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.3
• /
• pp.71-78
• /
• 2001

This paper presents the results of an experimental investigation on the combustion of single droplets arrays of Ethyl alcohol and kerosene fuel droplets in atmospheric pressure. The initial droplet diameters, d$_{0}$, were nominally 1.3~1.8mm, and inter-droplet separation distance l(l/do=1.31~2.60). experimental results indicate that burning rate constants(K) of ethyl alcohol and kerosene droplets were independent of initial droplet size as 0.0083, 0.0095 $\textrm{cm}^2$/sec. For 1-D droplet array's kerosene fuel droplet, burning rate constants(K) decreases with decreasing normalized inter-droplet distance. Normalized inter-droplet distance has stronger effect on 2nd fuel droplet than 3rd fuel droplet. When normalized inter-droplet distance is larger than 2.60, the effect of droplet spacing on droplet life is very small.