• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.43.1-43.1
• /
• 2010

In the crystalline silicon solar cells, the full area aluminum_back surface field(BSF) is routinely achieved through the screen-printing of aluminum paste and rapid firing. It is widely used in the industrial solar cell because of the simple and cost-effective process to suppress the overall recombination at the back surface. However, it still has limitations such as the relatively higher recombination rate and the low-to-moderate reflectance. In addition, it is difficult to apply it to thinner substrate due to wafer bowing. In the recent years, the dielectric back-passivated cell with local back contacts has been developed and implemented to overcome its disadvantages. Although it is successful to gain a lower value of surface recombination velocity(SRV), the series resistance($R_{series}$) becomes even more important than the conventional solar cell. That is, it is a trade off relationship between the SRV and the $R_{series}$ as a function of the contact size, the contact spacing and the geometry of the opening. Therefore it is essential to find the best compromise between them for the high efficiency solar cell. We have investigated the optimal design for the local back contact by using PC1D simulation.

• 한국HCI학회:학술대회논문집
• /
• 2006.02a
• /
• pp.836-842
• /
• 2006

3D 애니메이션 제작에서 동작의 타이밍(예를 들면 timing&spacing, slow-in, slow-out)은 연기의 의미와 느낌을 정확히 표현하기 위한 매우 중요한 요소 중의 하나이다. 따라서 이러한 타이밍의 편집은 애니메이션 작업에서 필수적이라고 할 수 있는데, 이를 기존의 3D 애니메이션 시스템에서 수행하기에는 기술적으로 많은 어려움이 있었다. 첫째로 타이밍의 편집은 시간축 자체를 변형하는 문제이기 때문에 보간 곡선에 대한 재매개변수화가 필요한데, 이러한 가능은 기존 애니메이션 시스템에서 제공되지 않는다. 둘째로 타이밍 편집에는 종종 애니메이션 감독이 직접 참여하기도 하는데, 일반적으로 3D 애니메이션 시스템의 사용에 익숙하지 않기 때문에 원하는 결과를 직접 만들어 보기가 어려웠다. 본 논문에서는 이러한 문제들을 해결한 새로운 애니메이션 타이밍 시스템을 구현하였다. 이 시스템은 렌더링된 영상파일들과 애니메이션 장면 파일을 입력 받아 사용자가 타이밍 편집을 하고, 그 결과를 애니메이션 장면 파일에 다시 기록하는 방식으로 구현된다. 타이밍 편집은 기존 셀 애니메이션 제작 방식과 유사한 방식으로 프레임을 삽입하거나 삭제하는 가능과 시간왜곡 (time-warping) 그래프를 직접 조정하여 타이밍을 조정하는 가능을 제공한다. 전자는 제작도구에 익숙하지 않은 감독이나 셀 애니메이션 작업자들이 직관적으로 사용할 수 있는 기능이고, 후자는 좀 더 세밀한 타이밍 조정을 위해 제공하는 가능이다. 사용자가 편집한 타이밍 결과는 각 동작변수의 보간곡선을 재매개변수화하여 애니메이션 파일에 기록된다. 본 논문에서 구현한 시스템은 실제 애니메이션 제작에 보편적으로 사용되는 마야 애니메이션 파일을 지원하도록 구현되었다.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.3
• /
• pp.352-357
• /
• 2016

An investigation of ribbed divergent channel was undertaken to determine the effect of rib pitch to height ratio on total friction factor and heat transfer results in the fully developed regime. The ribbed divergent rectangular channel with the channel exit hydraulic diameter ($D_{ho}$) to inlet channel hydraulic diameter ($D_{hi}$) ratio of 1.16 with wall inclination angle of 0.72 deg, at which the ratios (p/e) of 6,10, and 14 are considered. The ribbed straight channel of $D_{ho}/D_{hi}=1.0$ were also used. The ribbed divergent wall is manufactured with a fixed rib height (e) of 10 mm and the ratio of rib spacing (p) to height 6, 10, and 14. The measurement was run with range of Reynolds numbers from 24,000 to 84,000. The comparison shows that the ratio of p/e=6 has the greatest thermal performance in the divergent channel under two constraints; identical mass flow rate and identical pressure drop.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.152-158
• /
• 2009

We have developed a novel digital feedback predistortion(DFBPD) linearization based on RF feedback PD for the wide bandwidth modulated signals. The wideband PD operation is carried out by combining the DFBPD and memory lookup table(LUT). To experimentally demonstrate the linearization performance of the proposed PD technique for wideband signal, a class-AB amplifier using an LDMOSFET MRF6S23140 with 140-W peak envelope power is employed at 2.345 GHz. For a forward-link 2FA wideband code-division multiple-access signal with 10 MHz carrier spacing, the proposed DFBPD with memory LUT delivers the adjacent channel leakage ratio at an 10 MHz offset of -56.8 dBc, while those of the amplifier with and without DFBPD are -43.2 dBc and -41.9 dBc, respectively, at an average output power of 40 dBm. The experimental result shows that the new DFBPD with memory LUT provides a good linearization performance for the signal with wide bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.12 s.91
• /
• pp.1207-1215
• /
• 2004

A Gigabit Ethernet upstream transmission over a WDM-PON employing remotely wavelength-locked Fabry-Perot lasers has been demonstrated. We have successfully demonstrated a WDM transmission of four Gigabit Ethernet channels with 100 GHz channel spacing over 30 km conventional single mode fiber. The measured f-factor was larger than 17.1 dB. We have also investigated the beating noise characteristics of a wavelength-locked Fabry-Perot laser and showed the remotely wavelength-locked Fabry-Perot laser suppresses the intensity noise of the incoherent light injected, which cause a 6.3 dB SNR improvement compared with that of the conventional spectrum-sliced light source.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.183-190
• /
• 2006

Digital 3D Real Object Duplication System (RODS) consists of 3D Scanner and Solid Freeform Fabrication System (SFFS). It is a device to make three-dimensional objects directly from the drawing or the scanning data. In this research, we developed an office type SFFS based on Three Dimensional Printing Process and an industrial SFFS using Dual Laser. An office type SFFS applied sliding mode control with sliding perturbation observer (SMCSPO) algorithm for control of this system. And we measured process variables about droplet diameter measurement and powder bed formation etc. through experiments. In case of industrial type SFFS, in order to develop more elaborate and speedy system for large objects than existing SLS process, this study applies a new Selective Dual-Laser Sintering (SDLS) process and 3-axis Dynamic Focusing Scanner for scanning large area instead of the existing f lens. In this process, the temperature has a great influence on sintering of the polymer. Also the laser parameters are considered like that laser beam power, scan speed, and scan spacing. Now, this study is in progress to evaluate the effect of experimental parameters on the sintering process.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.4
• /
• pp.1458-1471
• /
• 1996

The present study is concerned with the heat transfer enhancement associated with a symmetrical or asymmetrical horseshoe vortex in front of and around the circular cylinder centered between the side walls of a wind tunnel. The static pressure measurements and the flow visualization in front of and around cylinders have been performed to determine the existence of horseshoe vortex. The hue-capturing method using the thermochromatic liquid crystals with great spatial resolution was used to obtain the local information of the endwall heat transfer coefficients. In case of one cylinder, the convective heat transfer coefficients of the region where the horseshoe vortex exists are larger than those of any other region. In case of two cylinders with tandem arrangement, the heat transfer rate of gap spacing (d/D= 1.5) is higher than that of gap spacings (d/D=2.0 or 2.5).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.10A
• /
• pp.988-995
• /
• 2006

In this Paper, we Present a nonharmonic may geometry design method using Euclidan minimum distance function in difference Phase spaces for 2-D (azimuth/elevation) multiple baseline antenna may which has a way to reduce the number of sensor antennas while maintaining accurate DOA estimate. The major advantages of our approach is that even the shortest interelement spacing can be larger than half-wavelength and is not limit13d to linear and it can be applied successfully to any array configuration. In multiple signals impinging situation, the performance simulation results of superresolution algorithms shows the effectiveness of the proposed method. Also the 2-D asymmetric may using the Proposed method is designed and the Performance of the manufactured away through the experimental test is verified.

• Steel and Composite Structures
• /
• v.19 no.5
• /
• pp.1299-1319
• /
• 2015

This paper presents a detailed parametric study, conducted using finite element tools to cover a range of several geometric and material parameters, on the behaviour of thin-walled partially encased composite (PEC) columns. The PEC columns studied herein are composed of thin-walled built-up H-shaped steel sections with concrete infill cast between the flanges. Transverse links are provided between the opposing flanges to improve resistance to local buckling. The parametric study is confined to eccentrically-loaded columns subjected to major axis bending only. The parameters that were varied include the overall column slenderness ratio (L/d), load eccentricity ratio (e/d), link spacing-to-depth ratio (s/d), flange plate slenderness ratio (b/t) and concrete compressive strength ($f_{cu}$). The overall column slenderness ratio was chosen to be the primary variable with values of 5, 10 and 15. Other parameters were varied within each case of L/d ratio. The effects of the selected parameters on the behaviour of PEC columns were studied with respect to the failure mode, peak axial load, axial load versus average axial strain response, axial load versus lateral displacement response, moment versus lateral displacement behaviour and the axial load-moment interaction diagram. The results of the parametric study are presented in the paper and the influences of each of the parameters investigated are discussed.

• Computers and Concrete
• /
• v.16 no.5
• /
• pp.759-774
• /
• 2015

This study simulates the flexural behavior of ultra-high-performance fiber-reinforced concrete (UHPFRC) beams reinforced with steel and glass fiber-reinforced polymer (GFRP) rebars. For this, micromechanics-based modeling was first carried out on the basis of single fiber pullout models considering inclination angle. Two different tension-softening curves (TSCs) with the assumptions of 2-dimensional (2-D) and 3-dimensional (3-D) random fiber orientations were obtained from the micromechanics-based modeling, and linear elastic compressive and tensile models before the occurrence of cracks were obtained from the mechanical tests and rule of mixture. Finite element analysis incorporating smeared crack model was used due to the multiple cracking behaviors of structural UHPFRC beams, and the characteristic length of two times the element width (or two times the average crack spacing at the peak load) was suggested as a result of parametric study. Analytical results showed that the assumption of 2-D random fiber orientation is appropriate to a non-reinforced UHPFRC beam, whereas the assumption of 3-D random fiber orientation is suitable for UHPFRC beams reinforced with steel and GFRP rebars due to disorder of fiber alignment from the internal reinforcements. The micromechanics-based finite element analysis also well predicted the serviceability deflections of UHPFRC beams with GFRP rebars and hybrid reinforcements.