• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.834-835
• /
• 2006

Manganese is an alloying element that improves the hardenability of steels. It could be a valid substitute in sintered steels, increasing mechanical properties. The hardenability of three low alloy Mn steels was studied to establish the influence of manganese on the heat treatments. The Grossmann approach was adopted, which uses cylinders with different diameters to induce different gradients of cooling rate in the cross section. The correlation of microstructure and microhardness to the actual cooling rate makes the results independent on the process parameters and applicable to each industrial condition, once the actual cooling rate in the parts is known.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.81-88
• /
• 1993

This report describes the experimental research on the flow phenomena of the aq uaous polymer solution within the Cuette flow of the concentric, cylinders type with a wide circular gap. We have investigated the phenomena of the fluid flow through torque measuring in the system that the inner cylinder is stationary and the outer one is rotating. Geometrical parameters of the system are the gap ratio of t/R$_{0}$=0.2 and Aspect ratio of l/t=100. The torque increases considerably in about 420-480RPM, So, it is considered a turbulent transition boundary, the higher plymer concentration is, the lower torque value is and the higher transition Reynolds number is. In each of the polymer concentration, the unstable boundary of torque, that is, idiosyncrasies of torque is observed around 220-280RPM. and the boundary is looked upon as a resonant vibration which is caused by the inner cylinder and tortional vibration of torque sensor.r.

• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.5
• /
• pp.686-692
• /
• 1999

For the purpose of increasing compressed air pressure higher than 30bar lightening weight and decreasing installation area of air compressor used for shipboard and industrial power plant it is necessary to arrange its cylinders as a w-type or v-type construction multi-stage compression pro-cess more than two stages and to increase its operation speed higher than 1200rpm In this recip-rocating type air compressor operated in high speed having a crank mechanism and complicate cylinder arrangement there is a vibration problems which can be solved by balancing its recipro-cating parts with balance weight and approriate arranging of cylinder's arrangement angles.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.1
• /
• pp.26-36
• /
• 1996

Many researches were carried out to estimate heat transfer rate on a circular cylinder in a uniform flow. Various empirical correlations were suggested in the past through experimental studies, however there are considerable discrepancies in the estimated values of heat transfer coefficient. The effect of fluid physical properties on the forced convective heat transfer between a circular cylinder and the external flow was numerically investigated in the present study, The flow and temperature fields were solved using a Finite Volume Method over a wider range of Prandtl number(0.7-40,000) than existing correlations. The cold as well as the hot cylinders in the uniform liquid flow of constant temperature were investigated. A unified correlation was obtainde for both cases.

• Proceedings of the Safety Management and Science Conference
• /
• 2005.05a
• /
• pp.443-452
• /
• 2005

In order to enhance the quality of the glass bottle and to preserve the contents long, corrosion of the bottle surface is often required. The corrosion operation consists of dangerous and harmful tasks using strong acid such as HF. Thus, the corrosion operation should be automatized to improve the worker's safety. The first step of the automation is to develop the bottle gripping system that automatically grips and fixes the bottle during corrosion operations. The gripping system consists of holders, holder plates, air cylinders, and bottle aligning system. This paper shows the gripping system development procedure.

• Proceedings of the ESK Conference
• /
• 1997.10a
• /
• pp.214-219
• /
• 1997

In spite of many accidents still occur repeatedly. The reason why we have so many accidents in industrial plants is mainly due to lack of effective safety education. Most safety education committed by safety staff is composed of general education and/or accident case studies. However, it is quite natural that the safety education should be more task- specific rather than general, if it be effective. Thus for preventing gas leakage accidents during changing explosive gas cylinders, this study aimed to analyze a manual chaning work in semiconductor plants, and to deaw importamt educational points. With the help of HRA and ETA, the most important task truned out to be reconfirmation of regulator gauges. Under the assump- tion of independent events, the estimated leakage probability was 23004E-05 which seriously understimated the probability, 8.1008E-05 under the assumption of dependent events. And the most probable situation would be gas leakge from the used gas cylinder. It was made clear that the assumption of independence could distrot safety educational focus.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.3
• /
• pp.263-272
• /
• 2008

We implemented a real-time servo system for a manipulator based on Laser Range Finder (LRF). and established algorithms for grasping a moving cylinder. We devised a manipulator mechanism and driving hardware based on a system board equipped with Xscale Processor with real-time operating system RTAI on Linux. The manipulator motor driver is connected to the system board via CAN communication link, and LRF is connected via RS-232C. We implemented real-time software including CAN device driver, RS-232C device driver, manipulator trajectory generator, and LRF control software. A typical application experiment for grasping a cylinder with circle motion demonstrated our system's real-time performance.

• Journal of Computational Design and Engineering
• /
• v.3 no.2
• /
• pp.121-131
• /
• 2016

Organic modeling of 3D characters is a challenging task when it comes to correctly modeling the anatomy of the human body. Most sketch based modeling tools available today for modeling organic models (humans, animals, creatures etc) are focused towards modeling base mesh models only and provide little or no support to add details to the base mesh. We propose a hybrid approach which combines geometrical primitives such as generalized cylinders and cube with Shape-from-Shading (SFS) algorithms to create plausible human character models from sketches. The results show that an artist can quickly create detailed character models from sketches by using this hybrid approach.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.23 no.2
• /
• pp.27-32
• /
• 1986

This paper describes an application of the adaptive finite element computations to a free surface flow problem in a canal. A-posteriori error estimates for the adaptive finite element computations are based on the dual extremum principles. Previously the dual extremum principles were applied to compute the upper and lower bounds of the added mass of two-dimensional cylinders in a canal[1,2]. However, the present method improves the convergence of the computed results by utilizing the local error estimates and by applying the adaptive meshes in the finite element computations. In a test result using triangular elements it is shown that the numerical error in the adaptive finite elements reduces quadratically compared with that in a uniform mesh subdivision.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.10a
• /
• pp.101-107
• /
• 1996

In this study, the wedge splitting test (WST) specimens with various strength levels were tested to investigate the fatigue crack growth behavior of concrete. Selected test variables were concrete compressive strength with 2 levels (28 MPa, 60 MPa, 100 MPa) and maximum fatigue loading with 2 levels (75%, 85%). Fatigue testing was preceded by fracture energy test and the crack growth was measured by means of the compliance calibration method, 60 WST specimens were cast for the fatigue test, and 6 companion cylinders ($\phi$100${\times}$ 200 mm) for each batch. In fatigue test, the frequency of loading cycle was 1 Hz, and the minimum fatigue loading level was 5~10 % of ultimate monotonic loading. On the basis of the experimental results, a fracture mechanics-based empirical relationships for fatigue crack growth rate (da/dN-$\Delta$KI relationships) were presented. In addition, the effect of initial notch depth on the fracture energy and the validity of compliance calibration technique for the WST were shown.