• International Journal of Fluid Machinery and Systems
• /
• v.6 no.3
• /
• pp.121-136
• /
• 2013

This paper reports the 1-D fluid transient simulation results of the discharge flow conditions in a 6-cylinder reciprocating slurry pump. Two discharge manifold configurations are studied comparatively; a case with a hexagon shaped discharge manifold where each cylinder discharges at a single vertex, and a case where all the cylinders discharges are lumped together into a tank shaped manifold. In addition, the study examines the effect of two pulsation mitigation measures in the case of hexagonal manifold; a single inline orifice in one of the hexagon sides and a volumetric dampener at the manifold outlet. The study establishes the pressure and flow fluctuation characteristics of each configuration and decouples the pulsation characteristics of the pump and the discharge manifold.

• Journal of electromagnetic engineering and science
• /
• v.12 no.1
• /
• pp.115-121
• /
• 2012

This paper presents a scattering model and measurements of backscattering coefficients for soybean fields. The polarimetric radar backscatters of a soybean field were measured using the ground-based X-band polarimetric scatterometer in an angular range from $20^{\circ}$ to $60^{\circ}$. The backscattering coefficients were also obtained using the COSMO-SkyMed (Spotlight mode, HH-polarization) from July to October 2010. The backscattering coefficients of the soybean field were computed using the 1st-order radiative transfer model (RTM) with field-measured input parameters. The soybean layer is composed of the stems, branches, leaves, and soybean pods. The stems, branches, and pods are modeled with lossy dielectric cylinders, the leaves are modeled with lossy dielectric disks. The estimated backscattering coefficients agree quite well with the field-measured radar backscattering coefficients.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.922-930
• /
• 1999

This paper describes a new 14-CPU real-time distributed automatic gauge control (AGC) system for POSCO's No. 2 Hot Strip Mill at Pohang Works. The new AGC system has adopted gaugemeter AGC, Monitor AGC, and roll gap disturbance compensators. The computer system for the new AGC system has been developed based on VMEbus computer systems and a commercial real-time operating system. A VMEbus computer system is also used for the position servo control of hydraulic cylinders. All the application programs and input/output signals have been reasonably distributed over the control computer systems for the maximum reliability and effectiveness of the system. The new AGC system has been successfully used for the No. 2 Hot Strip Mill.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.2
• /
• pp.160-168
• /
• 1982

수평으로 놓여진 2개의 동심타원 사이의 환상공간에서의 자연대류현상이 수치계산 및 실험적으로 연구되었다. 수치적 연구는 정상 2차원 층류유동영역에서 수행되었으며 유선 및 등온선이 구하여 졌다. 또한 특수한 경우로서 수평동심원 사이의 환상공간에 관한 기존연구와 비교하여 좋은 일치 를 보았다. 실험적 연구에서는 3개의 실험모델을 제작하였으며 마하젠더 간섭계에 의한 간섭사진 으로부터 등온선 분포를 얻었으며 아울러 유동에 관한 정보도 얻을 수 있었다. 실험과 수치계산 결과는 상당히 좋은 일치를 보였으며 기존 동심원환상공간에 편심율이 추가된 이론전개 및 수치 계산방법의 적합성을 알 수 있었고 이로서 환상공간에서의 자연대류에 관한 연구를 확장시켰다.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.980-985
• /
• 2004

This paper shows a performance analysis for conical type sealless cylinders and rod bearings. The pistons without seal have partly cylindrical and conical shapes. 2 dimensional Reynolds equation and FD(finite differential) numerical techniques are utilized for the performance analysis. The relationship among self-centering forces and leakage flows are investigated. Also, optimal design values for a sealless cylinder are presented. A prototype of sealless cylinder which had rod bearing with four pockets, five pockets, and six pockets was manufactured respectively. Leakage flow test is conducted to evaluate performance of piston and rod bearing in sealless cylinder.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1141-1151
• /
• 1998

An effective thermal conductivity measurement for suspensions of microparticles in oil mixture is conducted in order to evaluate the shear rate-dependence of the thermal conductivity of suspensions. Measurements are made for rotating Couette flows between two concentric cylinders. The rotating outer cylinder is immersed into a constant temperature water bath while the stationary inner cylinder is subject to a uniform heat fluff. Test fluids are made to be homogeneous suspensions, in which neutrally buoyant microparticles ($d=25{\sim}300{\mu}m$) are uniformly dispersed. The present measurements show strong shear-rate dependent thermal conductivities for the suspensions, which are higher than those at zero shear rate. The shear rate dependent thermal conductivity increases with the particle size and volume concentration.4 new model for shear rate-dependent thermal conductivity of microparticle suspensions is proposed; the correlation covers from zero shear rate value to asymptotic plateau value at moderately high shear rates.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.6
• /
• pp.411-417
• /
• 2009

The transient shear stress response of an electrorheological fluid is investigated experimentally. The characteristic time constants of an electrorheological fluid sheared between two concentric cylinders were obtained under various electric field strengths and shear rates. Also, two experimental modes are adopted to investigate the effect of the shear flow on the dynamic behavior of the fluid; one is that the electric field is induced before shearing, and the other is the electric field is induced after shearing. From the difference in the response time between two modes, the cluster formation time were obtained. The response times were decreased with the increase of the shear rate, irrelatively of the electric field strength. The cluster formation time were monotonically increased with increase of shear rate, and thereafter, were converged with a certain value.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.3 no.1
• /
• pp.37-47
• /
• 1995

It is very important to determine the performance and operating envelope of engine for aircraft's flight. The basic performance is provided by manufacturer, but installed engine's operating envelop is only determined by flight test. First, this study was measured cylinder head temperature(CHT), exhaust gas temperature(EGT) and oil temperature. At pre-determined altitude and power rate, these temperatures were measured by change of mixture ratio and mixture ratio condition for economic operation and max. power were found. And secondly, with the measured temperatures, possible positions of mixture lever were determined by flight test for stable flight Chang-91 and Lycoming IO-360-A series four cylinders engine with 200 hp was used for this study.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.218-226
• /
• 2002

This study was carried out to develop continuously variable-speed transmission(CVT) fur an agricultural tractor. The full-toroidal variator mechanism with flour discs and six rollers was utilized as a device fur changing speed ratio continuously. In system layout design, the sizes of the roller cylinders and the end-load cylinder, which were critical factors for controlling the variator, were designed. The planetary gear unit and six pairs of the gear assemblies were designed to establish the maximum speed of the vehicle at 30 ㎞/hr. In addition, the hydraulic clutch, the silent chain, the hydraulic manifold and the electronic controller were designed. Based on the design, a prototype CVT was developed and tested. Test results show that the CVT developed in this study could successfully provide variable speed of the tractor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.143-150
• /
• 2002

The characteristics of rubber cup seal is highly nonlinear due to the nature of the material's non-linearity and large deformation with frictional contact. And the performance of sealing in master cylinders of automobile is one of the most important factors which affects the safety of drivers. The effects of various shape of the primary cup seal in clutch master cylinder was investigated to reduce oil leakage and to obtain a long reliable life. Deformation and distribution of stresses on the primary cup seal against hydraulic oil pressure were analyzed with changing design parameters such as depth and radius in cup-seal. The obtained results indicate that the depth of cup seal plays a major role on deformation resulting in the sealing force to the wall of clutch master cylinder.