• Title/Summary/Keyword: cutting test

검색결과 772건 처리시간 0.029초

25Cr-20Ni계 스테인리스강의 크리프 변형중 내부응력과 운동전위밀도의 평가 (Evaluation of Internal Stress and Dislocation Velocity in Creep with 25Cr-20Ni Stainless Steels)

  • 박인덕;안석환;남기우
    • 대한기계학회:학술대회논문집
    • /
    • 대한기계학회 2004년도 춘계학술대회
    • /
    • pp.296-301
    • /
    • 2004
  • By the purpose to investigate the change of internal stress and mobile dislocation density in creep, the stress relaxation test is carried out in the condition of each strain. Mobile dislocation density increased until it reached minimum creep rate and after that, it decreased and internal stress didn't have the change approximately until it reached minimum creep rate and after that, it decreased. The stress relaxation rate is fast and approached zero after 1.5 seconds after the beginning of the stress relaxation. And the larger the applied stress is, the larger the internal stress is. By the evaluation of mobility of dislocation, the dislocations glide viscously in STS31OJlTB but it is the dislocations glide viscously which N passes by cutting Cr atom rather than typical viscosity movement after calculating mobility of dislocation.

  • PDF

태백지역 석탄광산의 작업부서별 호흡성 분진 폭로농도 (Respirable Cool Dust Exposure Concentration at Work Sites of Underground Coal Mines in Taebaek Area)

  • 윤영노;정호근
    • 한국산업보건학회지
    • /
    • 제1권1호
    • /
    • pp.47-55
    • /
    • 1991
  • Exposure level of respirable coal dust of underground coal mines in Taebaek area was evaluated. Personal air samplers with 10-mm nylone cyclones were attached to the coal workers including drillers, coal cutters, their assistants, haulers, and separators. Log-normality of respirable dust exposure concentration were tested by Kolmogorov-Smirnov one-sample test. Differences of means of respirable dust exposure concentration between work sites were tested by one-way ANOVA test and multiple comparison(Scheffe) test. And differences of respirable dust exposure concentration of principal and assistant workers in drilling sites and in coal faces were tested by paired t-test. Relation of respirable dust exposure concentration for the principal workers and their assistants in drilling sites and in coal faces were tested by regression analysis. The results were as follows : 1. All of the respirable dust concentration were log-normally distributed. 2. There were not only significantly different means of exposure concentration between drillers and coal cutters but between coal cutters and haulers. 3. Means of exposure concentration of drillers and drilling assistants were not significantly different. And means of exposure concentration of coal cutters and coal cutting assistants were not different.

  • PDF

미세정밀밀링 가공을 위한 검사시편의 가공조건에 따른 표면거칠기에 대한 영향 분석 (The Effect of Surface Roughness according to Machining Conditions of Test Specimen for Precision Micro-milling Machining)

  • 심민섭;김동현;이춘만
    • 한국정밀공학회지
    • /
    • 제32권1호
    • /
    • pp.49-55
    • /
    • 2015
  • Recently, many researchers and industry are looking for ways to decrease the use of lubricants because of economical and environmental reasons. One of the lubrication technologies is the MQL method. This study presents a research of MQL and Wet milling processes of Al 6061 material. For this experiment, the test specimen is suggested, and various machining conditions are applied. And, shape of micro-pattern which has been recently spotlighted is included in the test specimen. In order to compare MQL with Wet machining, several milling experiments were carried out, varying feed rate, cutting speed, depth of cut, etc. Finally, the surface roughness results of machining tests according to the process conditions were measured. It is expected that the results of machining experiments can be used to predict the surface roughness of various MQL milling processes.

선형절삭실험 중 디스크커터 축에 작용하는 하중과 온도에 대한 실험적 연구 (A experimental study on the loads and temperature acting on the shaft of a disc cutter during linear rock cutting test)

  • 최순욱;장수호;박영택;이규필;배규진
    • 한국터널지하공간학회 논문집
    • /
    • 제15권3호
    • /
    • pp.237-251
    • /
    • 2013
  • 본 연구는 변형률게이지와 열전대, 적외선 열화상카메라를 사용하여 선형절삭실험 동안 디스크커터의 축에 발생하는 축응력과 토크를 측정하고 디스크커터의 내부와 외부의 온도를 파악하고자 하였다. 실험결과, 축응력과 토크의 최대값은 각각 11.3 MPa, $171kN{\cdot}m$로 측정되었으며, 축응력과 토크는 회전력보다는 디스크커터의 연직력과 상관성이 높은 것으로 나타났다. 선형절삭실험 동안 열전대로 측정한 결과, 디스크커터의 온도변화는 $0.2^{\circ}C$ 이내로 나타났다. 그러나 수행된 각 선형절삭작업이 연속적으로 이루어진다고 가정한 다음, 디스크커터의 내부온도와 커터 링 표면의 온도변화를 추정한 결과, 커터간격이 70 mm인 경우에는 각각 $0.1^{\circ}C/m$, $0.15{\sim}0.17^{\circ}C/m$로 예상되었고 커터간격이 90 mm인 경우에는 각각 $0.09^{\circ}C/m$, $0.13{\sim}0.23^{\circ}C/m$로 추정되었다.

선형절삭시험에 의한 코니컬커터의 삽입재 크기에 따른 절삭성능 평가 (Performance estimation depending on the insert size of conical picks by linear cutting test)

  • 최순욱;강태호;장수호;이철호;이규필;김창용
    • 한국터널지하공간학회 논문집
    • /
    • 제18권2호
    • /
    • pp.221-233
    • /
    • 2016
  • 본 연구는 로드헤더 커팅헤드에 사용되는 코니컬커터의 삽입재 크기에 따른 커터작용력의 변화를 살펴보기 위하여 절삭간격과 절삭깊이, 그리고 사각을 변화시키면서 연직력, 절삭력, 구동력을 측정하였고 그 측정결과의 평균값을 사용하여 분석을 실시하였다. 절삭간격이 12~27 mm인 조건에서 절삭깊이에 따라 평균 커터작용력이 일정한 범위에서 나타났다. 사각이 $0^{\circ}$인 경우에서는 일반적으로 알려진 최적 S/d비 1~5사이인 4~4.5 조건에서 비에너지가 최소로 나타났으며, 사각이 $6^{\circ}$인 경우에서는 최적 S/d비가 좀 더 작은 1~3에서 나타났다. 단순히 시험결과에 의한 비교에서는 슬림 코니컬커터가 헤비 코니컬커터에 비해 절삭효율이 좋게 나타났지만, 대상지반의 강도가 높을 경우에 대해 커터의 소모량과 손상을 고려한다면 헤비 코니컬커터의 사용이 효과적일 것이다.

서울 시내 산업체 급식소의 plastic용기 및 기구류 위생에 관한 연구 (The Microbiological Assessment of Plastic Container and Kitchen Utensils Used in Employee Feeding Foodservice Operation in Seoul)

  • 전희정;백재은;이윤경;김은실
    • 한국식품조리과학회지
    • /
    • 제14권1호
    • /
    • pp.21-24
    • /
    • 1998
  • 서울 시내 산업체 단체 급식소 3곳에서 이용되는 플라스틱 용기, 행주, 도마, 식칼의 미생물 검사결과는 다음과 같았다. 플라스틱 용기의 표준 평판균수는 3곳 모두 1$\times$$10^{*}$ 5 (CFU/100 $cm^2$)으로 높게 나타났고, 대장균군 수는 두 급식소는 양호하나 한 급식소에서 2$\times$$10^1$(CFU/100$cm^2$)으로 높게 나타났다 전자현미경 관찰 결과 구균, 간균 형태의 박테리아가 많이 관찰되었다 행주의 경우는 표준 평판균수는 1$\times$$10^3$-1 $\times$$10^{*}$ 5 (CFU/100 $cm^2$)으로 3곳 모두 높게 나타났고, 대장균군 수는 한곳을 제외한 두곳에서 4$\times$$10^1$-6$\times$$10^1$(CFU/100 $cm^2$)으로 높게 나타났다. 식칼의 표준 평판균수는 1$\times$$10^3$-l$\times$$10^{*}$ 5 (CFU/300$cm^2$)으로 3곳 모두 높게 나타났고, 대장균군 수는 한곳을 제외한 두곳에서 2$\times$$10^1$-3$\times$$10^1$(CFU/100 $cm^2$)으로 높게 나타났다. 도마는 표준 평판균수가 1$\times$$10^{*}$ 5 (CFU/100 $cm^2$)으로 3곳 모두 높게 나타났고 대장균군 수는 한곳을 제외한 두곳에서 4$\times$$10^1$-9)$\times$$10^1$(CFU/100 $m^2$)으로 높게 나타나 기구류의 보다 철저한 위생관리가 요구되어졌다.

  • PDF

황령산 산사태 원인 분석에 대한 연구 (Study on Analysis for Factors Inducing the Whangryeong Mountain Landslide)

  • 최정찬;백인성
    • 지질공학
    • /
    • 제12권2호
    • /
    • pp.137-150
    • /
    • 2002
  • 최근 경상분지 퇴적암 지대에서 절개사면 형성 시, 20$^{\circ}$ 저각 경사의 층리면을 따른 평면파괴 양상이 빈번하게 발생하고 있다. 부산시에서 1999년 발생한 황령산 산사태도 이 범부에 속한다. 현재 황령산사면은 사면구배가 1:2.0으로 재조정 되어 2000년도에 공사가 마무리되었다. 황령산 산사태의 사면파괴형태에 대한 분석을 하기위하여 현장 암반조사 및 시험, 시추, 실내 시험, 항공사진판독, X-선 회절분석, 평사투영법 및 한계평형법을 이용한 사면 안정성 분석등이 실시되었다. 그 결과, 산사태 발생 1년 전부터 인장균열들이 연장 발달하는 것이 확인 되었고, 인장균열은 여러방향의 절리들이 합쳐저 생성된 것으로 생각된다. 파괴암체도 각각 다른 층리면을 따라 붕괴된 것으로 분석되었다. 평사투영법 및 한계평형법을 이용한 안정성 검토결과 활동면으로 작용한 녹회색 응회질 셰일층이 풍화된 경우 평면파괴의 위험성이 있는 것이 확인되었다. 향후 이와 유사한 지역에서 절개사면 건설 시, 박층의 풍화에 약한 층에 대한 세밀한 조사가 필요하며 이에 대한 안정성 분석이 수행되어야 한다.

나일론선 절단 방식에 기반한 Pin-puller형 큐브위성용 태양전지판 구속분리장치의 기능검증 (Functional Verification of Pin-puller-type Holding and Release Mechanism Based on Nylon Wire Cutting Release Method for CubeSat Applications)

  • 고지성;손민영;오현웅
    • 항공우주시스템공학회지
    • /
    • 제15권5호
    • /
    • pp.81-88
    • /
    • 2021
  • 일반적으로 큐브위성용 전개형 태양전지판을 수납 및 전개시키기 위해 사용되는 구속분리장치는 비폭발식 나일론선 절단방식이 적용된다. 그러나 상기 방식은 태양전지판 수납 상태에서 큐브위성의 배터리 충전, PCB 및 탑재체의 전기적 점검 및 시험 등을 위한 접근 포트 연결 시 분리장치의 구속해제 및 재채결 작업이 반복적으로 요구된다. 따라서, 기존의 구속분리장치는 위성체 내부 접근을 위해서는 작업자의 번거로움 및 일관된 나일론선 체결작업 공정 유지의 어려움이 존재한다. 본 연구에서는 나일론 선 절단 없이 구속 핀 분리만으로 자유롭게 태양전지판 전개 및 수납이 가능한 Pin-puller형 태양전지판 구속분리장치를 제안하였으며, 기능 및 성능검증을 위한 분리장치의 전개시험 및 최대 분리하중 측정 시험을 통해 분리장치 설계의 유효성을 입증하였다.

바인다의 효출력이 곡물탈립손실에 미치는 영향 (Effect of Bundle icing Forces on the Shattering Loss of Grains)

  • 백풍기;정창주
    • Journal of Biosystems Engineering
    • /
    • 제3권1호
    • /
    • pp.20-36
    • /
    • 1978
  • The effect of binder kicking forces on the shattering losses of paddy rice, which has been widely understood as an outstanding loss factor in harvesting with a binder, were experimentally assessed in this thesis.Through the field tests the optimum time of harvest, in terms of grain moisture contents, was found by considering harvesting losses for two rice varieties, harvested by two different binders, at four or five grain moisture levels.A device was designed and manufactured to apply various kicking forces to the bundles and was used in the bundle kicking tests. It was intended to find out the optimum range of kicking force to minimize the kicking losses. Based on the study, modification of the existing binder kicking mechanism was suggested. The following is a summary of the results of this thesis. 1. In Suweon 258 variety, as the grain moisture content is reduced, so the cutting loss and the kicking loss increase. The grain losses range from 0.77 to 0.82 percent of total field yield for the cutting loss, from 1.83 to 2.01 percent for the kicking loss, and from 2.60 to 2.83 percent for the field loss, when the moisture content is about 22 percent. 2. In Jinheung variety , the field losses increased as the grain moisture content decreased . When the moisture content was 20 percent, the field loss, cutting loss and kicking loss was 0.42-0.49 % , 0.30-0.35, and 0.12 -0.14% of the total field yield, respectively. 3. The difference in the field loss , cutting loss, and kicking loss for the two binders was 0.23% , 0.05% and 0.18% respectively in Suweon 258 variety, and 0.07% , 0.02% and 0.05% respectively ini Jinheung variety. The grain losses for binder B were slightly higher than those for binder A. 4. In the statistical analysis of each variety , the kicking force and the moisture content of the grain, and its interaction were all highly significant at 1% level by T test .The optimum kicking force was found to be in the 3.0-0.4kg range. This does not interrupt the binder operation, while ioses are kept to an acceptale level. 5. To reduce the kicking force of the eXlstmg binder mechanism, the speed of rotation of the kicking arm needs to be redued by increasing the number of driving sprocket teeth, and the position and gear ratio of the knotter-bill and driving bevelgear have to be change to give a !motter-bill speed of 1110 rpm. It is also desirable to attach a belt conveyor which smoothly carries the bundle to the ground. 6. The optimum harvesting time cased on maximum field yield was found to be at a grain moisture content of around 22 percent for Suweon 258 variety, and 20 percent for Jinheung variety. Tota] field yield and field yield at the time amounted to 9, 812.5 kg/ha, 9, 302. 5kg/ha respectively for the Suweon 258, and 7, 819.5 kg/ ha, 7, 158.7 kg/ha respectively for the Jinheung variety.

  • PDF

근삽에 의한 음나무의 무성번식 (Asexual Propagation of Kalopanax pictus by Root Cutting)

  • 김철우;송재모;배찬호;박봉재;문흥규;황석인;이재선
    • Journal of Forest and Environmental Science
    • /
    • 제18권1호
    • /
    • pp.1-6
    • /
    • 2001
  • 본 연구는 음나무의 증식을 위해 근삽을 이용하여 대량번식방법의 체계를 확립하고자 실시하였다. 조사된 결과는 다음과 같다. 1. 음나무의 근삽시 생장조절물질의 처리는 고농도보다 저농도가 효과적인 것으로 나타났으며, 생장조절물질 처리에 따른 부정아 발생율은 IBA, NAA 300mg/L 처리구에서 96.6%로 가장 높게 나타났으나 무처리 역시 90.0%로 높은 부정아 발생율을 나타내었다. 또한 엽의 특성(엽수, 엽신, 엽폭)은 무처리와 생장조절물질 처리간에 큰 차이를 나타내지 않았다. 2. 근의 방향에 따른 근삽은 가로근삽(100%)과 세로근삽 (92.5%) 이 모두 90% 이상의 부정아 발생율을 보여 두 처리 모두 높은 부정아 발생율을 나타내었고, 부정아 발생수 및 엽 특성(엽수, 엽병, 엽신 및 엽폭)에 있어서 세로근삽이 가로근삽보다 모두 높게 나타났다. 3. 바로묻기 한 것이 거꾸로묻기 한 것보다 부정아 발생율, 부정아 발생수 및 엽특성(엽수, 엽신, 엽폭)에서 높은 값을 나타냈으며, 거꾸로묻기 한 경우 세근의 발달이 없거나 미약하며, 부정아 발생의 경우 기극 부근에서 발생하여 지면으로 올라오는 경우를 나타냈다.

  • PDF