• 생물환경조절학회지
• /
• 제16권2호
• /
• pp.115-120
• /
• 2007

본 실험은 장미 삽수의 조제방법이 발근과 발근 후 생육에 미치는 영향을 알아보기 위하여 수행하였다. 실험재료로는 Rosa hybrida 'Red Sandra'와 'Little Marble' 두 품종을 사용하였다. 삽수 길이를 달리한 실험은 'Red Sandra'는 4, 7, 10cm, 'Little Marble'은 3, 5, 7cm 로 처리하였다. 소엽수를 달리한 실험은 삽수당 소엽 5매엽을 0, 2, 4, 또는 5매 남겼다. 삽수 채취부위를 달리한 실험은 꽃봉오리로부터 소엽 5매엽을 첫 마디로 하여 마디별 $1{\sim}2,\;3{\sim}4,\;5{\sim}6,\;7{\sim}8$마디로 4처리하였다. 발근과 생장에 있어 삽수 길이는 두 품종 모두 7cm가 좋았다. 발근률에 있어 소엽을 5매 모두 남기고 $1{\sim}2$마디를 삽수로 이용시 두 품종 모두 좋은 결과를 나타냈다.

• Journal of Oral Medicine and Pain
• /
• 제31권3호
• /
• pp.211-221
• /
• 2006

목적 전통적 고속 회전식 절삭기구 또는 Er:YAG 레이저로 삭제된 상아질에, 두가지 다른 접착 시스템을 적용한 후, 축조한 컴포지트 레진의 미세인장결합강도를 비교하고, 다양한 Er:YAG 레이저 에너지가 미세인장결합강도에 미치는 영향을 평가한다. 재료 및 방법 40개의 제3대구치를 사용하여, 평평한 상아질면을 만든 후 8개의 군으로 나누어, 4가지 절삭방법 (고속 회전식 절삭기구, 2 W, 3 W, 4 W 출력의 Er:YAG 레이저) 중 한 가지로 삭제하고, 2가지 접착 시스템 (Scotchbond Multipurpose Plus, Clearfil SE bond) 중 한 가지로 처리하여 컴포지트 레진을 축조하였다. 24시간의 저장 후, 각 시편을 결합면에 수직으로 자르고, 미세인장결합강도를 측정하였다. 각 군의 미세인장결합강도는 평균$\pm$표준 편차로 표현하였고, 통계분석을 위해 two-way ANOVA, one-way ANOVA, student-Newman-Keuls' multiple comparison test, 그리고 t-test가 사용되었다. 결과 및 결론 1. 접착시스템과 관계없이, 절삭방법에 따른 미세인장결합강도의 유의한 차이가 있었고, 높은 순서대로 나열하면 다음과 같다: 3 W, 2 W, Bur, 4 W (p<0.001). 2. 절삭방법과 관계없이, Scotchbond Multipurpose Plus로 처리한 군이 Clearfil SE bond로 처리한 군보다 유의하게 높은 미세인장결합강도를 나타냈다 (p<0.001). 3. Scotchbond Multipurpose Plus로 처리한 군 중에서, 3 W 레이저 절삭군이 가장 높은 미세인장결합강도를 나타냈고, 다음이 Bur, 2 W, 4 W 절삭군 순이었다 (p<0.001). 4. Clearfil SE bond로 처리한 군 중에서 3 W 레이저 절삭군이 가장 높은 미세인장결합강도를 나타냈고, 다음이 2 W, 4 W, Bur 절삭군 순이었다 (p<0.001). 5. 두 가지 접착 시스템 모두에서, 레이저로 절삭한 군의 미세인장결합강도의 차이가 있었고, 높은 순서대로 나열하면 3 W, 2 W, 4 W 순이었다 (p<0.001). :상아질에 접착된 컴포지트 레진의 미세인장결합강도는 절삭방법과 접착시스템의 상호작용에 의해 유의한 영향을 받았다. 임상에서 레진 수복시, 2 W-3 W 범위내로 Er:YAG laser를 사용한다면 전통적 핸드피스 못지않게 수복물의 우수한 결합강도를 얻을 수 있다. 특히 시술시간의 단축, 과도한 산부식에 따른 부작용의 예방을 위해 Clearfil SE bond를 포함한 self etching system을 사용하고자 한다면 bur보다 Er:YAG laser를 이용한 삭제방법이 더 유용한 결합력을 제공할 것이다.

• 한국방재학회 논문집
• /
• 제2권4호
• /
• pp.131-141
• /
• 2002

지하주차장을 PC화할 때 각각의 부재 접합상태에 따라 설계방법 및 시공방법에 많은 차이가 발생하게 된다. 특히 PC 벽체를 상호 연결하기 위한 접합부에서 수평철근을 겹침이음 방법에 의해 접합하는 경우, 수평철근의 이음길이를 충분히 확보하여야 하기 때문에 시공성이 저하되는 문제점이 있다. 따라서, PC 벽체 수평철근의 돌출길이를 최소화하기 위하여 철근 비부착 기법 및 철근 절단 기법을 적용하는 것을 본 연구의 목적으로 하고 있다. 즉, 철근 콘크리트 부재에서의 위험단면의 위치는 일반적으로 부재의 단부가 되고, 철근의 정착길이는 이 위험단면으로부터의 길이가 된다. 그런데 위험단면의 위치를 비부착 철근 공법 및 철근 절단 공법을 사용하여 부재 안쪽으로 이동함으로서, 수평철근의 정착길이를 최소화시킬 수 있다. 본 연구에서는 철근 비부착 기법 및 철근 절단 기법의 적용 가능성을 파악하기 위해 5개의 실험체를 실물크기로 제작하여 실험적 연구를 실시하고, 절단 철근 및 비부착 철근이 시험체의 거동에 미치는 영향을 비교 및 분석한 결과, 위험단면의 이동을 위하여 철근 비부착 기법 및 철근 절단 기법의 사용이 가능한 것으로 판단된다.

• 한국지리정보학회지
• /
• 제15권2호
• /
• pp.1-11
• /
• 2012

지구 환경 변화에 따른 폭우로 절토 사면 붕괴가 해마다 발생하고 인명과 경제적 손실이 증가하고 있다. 이는 절토 사면의 붕괴의 평가를 요구한다. 경사면이 절토 시행 전에 시뮬레이션 된다면, 절토 사면의 붕괴를 예측 할 수 있고, 붕괴 사고 시 복구 비용을 최소화 할 수 있다. 본 논문은 절토 사면에서 중요한 경사도의 시뮬레이션 방법을 나타낸다. 이것은 패트리넷을 이용하여 모델링되며 디자인되고, ArcGIS를 이용하여 윈도우 XP 환경에서 구현하고자 한다. 그래서 본 논문은 GIS를 이용한 절토와 간척을 시뮬레이션 함으로써 시간과 돈을 절약하는데 기여할 것이다.

• 산업경영시스템학회지
• /
• 제1권1호
• /
• pp.37-44
• /
• 1978

The purpose of this study is to search for an efficient application method in solving delay-phenomenon problems which influence upon total production cost through case study. The method of this study is an experimental study based on cutting time data in lead cutting operations from "Lead Cutting Machine (Stripper)" and its service rate data from a large electronic products company which utilizes conveyor line system for the products "Car Stereo" The procedure of this experimental study is as follows; 1) Using loading(Man-Hour) analysis technique j,1 order to analyse and evaluate Production capacity, efficiency, operation and idle rate assembly charge, waiting and service cost -when its are controlled by stripper operator(server) 2) Establishing adequate waiting time model of finite population caused by the interference of 4 stripper machine which is drawn from mathematical statistics testing, that is, goodness of fit test in the waiting and service rate and to search for optimal solution by utilizing the above mentioned model The experimental result was that amount to 8,546,618won Per year was brought down, that is, by optimum point, it shows a decrease as compared with Present point. The major limitation of this experimental study is that the Queue in the Finite Population, so to speak. it comes from the interference of 4 stripper machine dealt with this case were limited only on the Car Stereo conveyor line. Further study of application of this application method to the areas such as material handling, personnel management marketing and transportation management is strong1y recommended.trong1y recommended.

• 한국정밀공학회지
• /
• 제7권3호
• /
• pp.75-82
• /
• 1990

Automatic monitoring of the cutting conditions is one of the most improtant technologies in machining. In this study, the feasibility in applying acoustic emission(AE) signals for the in-process detection of endmill wear and fracture has been investigated by performing experimental test on the NC vertical milling machine with SM45C for specimen. As the results of detecting and analyzing AE signals on various cutting conditions, the followings have confirmed. (1) The RMS value of acoustic emission is related sensitively to the cutting velocity, but is not affected largely by feed rate. (2) The burst type AE signals of high level have been observed when removing chips distorderly and discontinuously. (3) When the RMS value grows up rapidly due to the increase of wear the endmill are generally broken or fractured, but when the endmills fracture at the conditions of smooth chip-flow or built-up-edge(BUE) occurred frequently, the rapid change of the RMS arenot found. And it is expected that this technigue will be quite useful for in-process sensing of tool wear and fracture.

• Restorative Dentistry and Endodontics
• /
• 제21권1호
• /
• pp.311-320
• /
• 1996

If root and resection is done during surgical endodontic treatment, newly exposed dentinal tubules form pathways between the canal and the peripheral tissue. Nd : YAG laser was used to block this phenomenon, and its effect was studied with dye penetration and SEM techniques. 40 intact single rooted teeth were divided into 4 groups(10 each) : control group and test groups, in which retrograde cavity surface, cutting surface, retrograde cavity surface & cutting surface were treated with laser(1 watt 15pps) and finally retrograde filling with IRM was conducted. After that, they were stained with 2 % methylene blue, sectioned and evaluated by the maximum infiltration depth. And to observe surface change, they were prepared for SEM. The results were as follows ; 1. All experimental groups showed microleakage with variation in amount. 2. The 2nd group which treated both the retrograde cavity and cutting surface showed significantly less microleakage than the other groups(p<0.05). There was no significant difference between groups treated on one side only. 3. As a result of SEM observation of dentin surface, obstruction of dentinal tubules with marble shaped granules, which were different from normal dentin could be seen. Cracks could be seen also. 4. In summary of this experiment, it is thought that effort to obstruct the exposed dentinal tubules as well as retrograde cavity after root end resection is needed.

• Journal of Biosystems Engineering
• /
• 제30권3호
• /
• pp.161-165
• /
• 2005

In this study, peeling test of the Altari radish on kimchi pre-processing system for mechanization was performed with the longitudinal plane peeling type with wider cutting blade than that of the peeled chip's. To determine the optimum cutter shape to match this plane peeling type, the peeling tests depending on variable cutting speed, rake angle and blade angle using the blade with thickness as 2 m and width as 50mm were performed, and the patterns of the peeled chips and peeling resistances were investigated. As the result of the tests, the rake angle of the blade with clean peeled surface of the Altari radish was over $45^{\circ}$, and the blade angle and rake angle with the minimum peeling resistance was $20^{\circ}\;and\;60^{\circ}$, respectively. The optimum peeling conditions were; the peeling speed 0.2m/s, blade angle $20^{\circ}$ and the rake angle $60^{\circ}$, and the peeling resistance of each blade was 15 N.

• Journal of Biosystems Engineering
• /
• 제34권4호
• /
• pp.228-233
• /
• 2009

In order to cut the round bale easily, a roughage cut-feeder for the round bale was developed in this study. This study consists of two parts. One is development of a cutting mechanism and a performance test reported in the previous paper. This is the second part of the study. For the study, recent trend of traditional cutting system was analyzed. Also, cost of the prototype cut-feeder was analyzed and determine the break-even point of farm size was determined by comparing with traditional method using a traditional cutter. A prototype cut-feeder was investigated with the fact that working performance, fiber length and shape of roughage and feeding quality was good. Operating cost of the prototype cut-feeder decreased rapidly with an increase of farm size. Break-even point in terms of farm size was 36 heads for beef and 28 heads for dairy. Also, costs estimated were 118,000 won/head year and 148,000 won/head year, respectively.

• 한국생산제조학회지
• /
• 제20권2호
• /
• pp.162-168
• /
• 2011

In this research, nitrogen plasma source ion implantation(PSII) of non-coated tungsten carbide endmill tools was conducted with low heat treatment for increasing wear resistance. After the low heat treatment of PSIIed tools to give a homogeneity of wear resistance, the surface modification of tools was analyzed by hardness test, surface roughness and cutting forces. As for the resultant cutting forces, low heat treatment in temperature of $400^{\circ}C$ and $500^{\circ}C$ is stable because of low cutting resistance. The 20-minutes heat treated tool at spindle speed 25000rpm has superiority of surface roughness, Ra of $0.420{\mu}m$ and was found to have good wear resistance. The higher hardness value was obtained by increasing temperature from $300^{\circ}C$ to $600^{\circ}C$ for PSIIed tools with low heat treatment. As the PSIIed tools under 10minutes at temperature of $600^{\circ}C$ have the highest hardness as Hv of 2349.8, It was analyzed that temperature processing give much influences on hardness.