• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.9
• /
• pp.2234-2241
• /
• 1993

The torque variation in drilling process represents the problems of the efficient and stable machining. In order to cope with them, the active control method is adopted to drill the workpiece under the constant cutting torque though the cutting stiffness of the workpiece or the diameter of the drill bit changes. The cutting process is modeled in the geometric viewpoint related with the feed and the number of cutting lips. And the dynamic model is approximated to the first order system for the purpose of control. The adaptive PI control is used in computer simulations and experiments. The results of the study show the validity of the drilling method with torque control.

• Journal of Mechanical Science and Technology
• /
• v.14 no.6
• /
• pp.622-632
• /
• 2000

In a high precision vertical machining center, the estimation of cutting forces is important for many reasons such as prediction of chatter vibration, surface roughness and so on. The cutting forces are difficult to predict because they are very complex and time variant. In order to predict the cutting forces of end-milling processes for various cutting conditions, their mathematical model is important and the model is based on chip load, cutting geometry, and the relationship between cutting forces and chip loads. Specific cutting force coefficients of the model have been obtained as interpolation function types by averaging forces of cutting tests. In this paper the coefficients are obtained by neural network and the results of the conventional method and those of the proposed method are compared. The results show that the neural network method gives more correct values than the function type and that in the learning stage as the omitted number of experimental data increase the average errors increase as well.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.243-246
• /
• 2000

Productivty of tapping has been increasing through the tcchnological advances in synchronization between spindle rotation and feed motion even in the high spindle speed. However, not much researches have been conducted about tapping process because its complicate cutting mechanism. In order ta investigate the characteristics of the tapping process, this paper concentrates on the analysis of curting torque behavior during one cycle of lapping. As one completc thread is performed through the whole chamfer ercuttlng, cutting torque increases highly in chamfer cutting, but smaothly in full thread cutting Functioning of the threads guide. Cutting torque in backward cutting is smaller than in Sorwerd cutting due to only friction farce in against between the tool and workpiece. And torque behavior of a periodic Sine ripple-mark was identified during one revolution of a tap.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.3
• /
• pp.350-356
• /
• 2011

In this paper, we proposed the automatic cutting mechanism of the perforation pipes in an automobile muffler. This cutting mechanism makes continuous work possible, because it performs the batch work via the sequential operation of loading, feeding, cutting, and discharging. The proposed cutting mechanism consists of the frame unit, escape unit, turning unit, feeding unit, vision system, clamping unit, spindle/cutting unit and cooling unit. And, these mechanisms have been modularized through mechanical, dynamical and structural optimized design using the SMO (SimDesigner Motion) analysis module. Also, the virtual prototype was carried out using the 3-D CAD program. The cutting process cycle is performed in the order of loading, vision processing, feeding, clamping, cutting and discharging. And the cycle time for cutting one piece was designed to be completed in four seconds.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.2
• /
• pp.85-94
• /
• 1994

The cutting mechanism of ultrasonic vibration machining is characterized as two phases, that is, an impact at the cutting edge and a reduction of cutting force due to non-contact interval between tool and workpiece. In this paper, in order to identify cutting dynamics of a system with ultrasonically vibrated cutting tool, an ARMA modeling is performed on experimental cutting force signals which have a dominant effect on cutting dynamics. The aim of this study is, through Dynamic Date System methodology, to find the inherent characteristics of an ultrasonic vibration cutting process by considering natural frequency and damping coefficient. Surface roughness and stability of cutting process under ultrasonic vibration are also considered

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.9
• /
• pp.1520-1530
• /
• 1997

Machining pressed compacts of ceramic and WC-Co materials can be the most cost effective way of forming the bodies prior to sintering when the required number of pieces is small. In this study, in order to clarify the machinability for turning, the $Si_3N_4$ and the WC-Co green compacts unsintered were machined under different cutting conditions with various tools. Absorbing chips by vacuum hose decreases tool wear. The tool wear becomes larger in the order of the ceramic, CBN and cemented carbide tools in machining the $Si_3N_4$ green compacts. In machining the WC-Co green compacts, the tool wear becomes larger in the order of the ceramic, cemented carbide and CBN tools. The land of cutting edge does not affect tool wear. When machining with cemented carbide tool, the tool wear i equal cutting length is nearly identical in spite of the increase of cutting spee, and the roughness of machined surface was the best in the cutting speed of 90 m/min. The tool wear decreases with the increase of rake angle and relief angle and with the decrease of nose radius. The machined surfaces become worse with the increase of feed rate and depth of cut, and with the decrease of rake angle and relief angle. The tool wear is not affected by the feed and depth of cut.

• Journal of Biosystems Engineering
• /
• v.20 no.1
• /
• pp.13-21
• /
• 1995

This study was conducted to investigate the cutting mechanism of reciprocating knife of combine harvester. The cutting operation of reciprocating knife with the arrangement of the low-cutting and the double-cutting was demonstrated through cutting pattern diagram which was drawn by computer graphics. Various kinds and dimensions of reciprocating knives were analyzed using the developed program. The results are summarized as follows (1) The low-cutting type reciprocating knife was represented similar cutting characteristics to the standard type, but the maximum stalk-deflection was decreased as 1/2 level of the standard type. And the first ledger plate should be designed shorter than the second ledger plate. (2) The bunching area and the maximum stalk-deflection for the double cutting knife almost were not changed since cutting velocity ratio of 0.6, but the secondary cut were occurred at ratio of 0.8 and increased rapidly over these ratio. (3) The double cutting knife was recommended for the high speed combine, because its bunching area and the maximum stalk-deflection were decreased as 1/2 level of the standard type. (4) In order to maintain the proper cutting mechanism characterized by the bunching area, the maximum stalk-deflection and the secondary cutting length etc., the adequate cutting velocity at forward speed of 0.5㎧ to 1.2㎧ was from 0.3㎧ to 0.96㎧ for the double cutting knives.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.1
• /
• pp.18-23
• /
• 2006

Cutting by a high speed laser cutting machine is one of most effective technologies to improve productivity. This paper has presented the cutting characteristics and optimal cutting conditions in a high speed feeding type laser cutting machine by using Tacuchi method in the design of experiment. An L9(34) orthogonal array is adopted to study the effect of adjustment parameters. The adjustment parameters consist of cutting speed, laser power, laser output duty and assistant gas pressure. The surface roughness of sheet metal is regarded as a quality feature. Analysis of variance is performed in order to evaluate the effect of adjustment parameters on the quality feature of laser cutting process.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.4
• /
• pp.419-424
• /
• 2004

In order to increase the efficiency of the sawdust machine, the helical type drums with an oblique cutting condition (3D) were developed. The preexisting drums have an orthogonal cutting condition (2D) considering of a saw cutter and a wood cutting pattern. Unfortunately, the disadvantages of this type drum are the big cutting resistance, the high cost of a cutting power and the extreme occurrence of a vibration. To improve this shortcoming, the helical type drum with an oblique cutting condition was developed. Therefore, this type drum decreased the vibration and the cutting resistance of the sawdust machine, and also improved the productivity of 30% or more and the porosity of the sawdust.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.11
• /
• pp.63-73
• /
• 1995

A mechanistic force system model considering the flank wear for the face milling process has been developed. The model predicts variation of the cutting forces according to flank wear in face milling over a range of cutting conditions, cutter geometries and cutting process geometries including relative positions of cutter to workpiece and rounouts. Flycutting and multitoth cutting teste were conducted on SS41 mild steel with sintered carbide tool. In order to verify the mechanistic force model considering the flank wear of cutting tools, a series of experiments was performed with single and multitooth cutters in various cutting conditions. The results show good agreement between the predicted and measured cutting force profiles and magnitudes in time and frequency domains.