• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.5
• /
• pp.173-179
• /
• 2000

While a cutting tool is machining a workpiece at various cutting depth, the feedrate is usually selected based on the maximum depth of cut. Even if this selection can avoid power saturation or tool breakage, it is very conservative compared to the capacity of the machine tools and can reduce the productivity significantly. Many adaptive control techniques that can adjust the feedrate to maintain the constant cutting force have been reported. However, these controllers are not very widely used in manufacturing industry because of the limitations in measuring the cutting force signals. In this paper, turning force control systems based on the estimated cutting force signals are proposed. A synthesized cutting force monitor is introduced to estimate the cutting force as accurately as a dynamometer does. Three control strategies of PI, adaptive and fuzzy logic controllers are applied to investigate the feasibility of utilizing the estimated cutting force fur turning force control. The experimental results demonstrate that the proposed systems can be easily realized in CNC lathe with requiring little additional hardware.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.6
• /
• pp.630-635
• /
• 2014

This study aims to develop a PZT-driven depth adjustment device with a flexure hinge and to investigate its static/dynamic characteristics. This device will be applied to rapidly and accurately trace a flat surface with slight waviness of up to several hundreds of micrometers in magnitude. One typical example is to cut a film coated on a steel plate. A depth control system composed of PMAC, PZT/PZT amplifier, flexure hinge/knife, and laser displacement sensor is implemented on a desktop three-axis machine and an actual cutting test is conducted on a steel workpiece with a sinusoidal-wavy surface. It is verified that the dynamic characteristics of the device limit the maximum cutting speed and depth precision.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.1043-1054
• /
• 1988

The optimum cutting condition of rake angle in turning was investigated in SM45C and SM20C. Results of experiments in SM45C and SM20C are as follow. Specific cutting resistance became higher as the depth of cutting, feed or cutting velocity decreases at same rake angle and resistance became low value at 20.deg.(SM45C), 10.deg.(SM20C). The optimum cutting condition for SM45C is depth of cutting 0.7mm, rake angle 30.deg., cutting velocity 200mm/min, feed 0.1mm/rev, and for SM20C is depth of cut 0.5mm, rake angle 10.deg., cutting velocity 150mm/min, feed 0.1mm/rev.The rake angle for good roughness is 15.deg for SM45C, and that for SM20C is 25.deg. The roughness is influenced by feed and it has the lowest value at 0.1mm/rev and the cutting condition is closely related with the change of cutting velocity and feed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.10a
• /
• pp.30-36
• /
• 1995

This paper proposed on the effective cutting conditions of cage motor rotor by turning. If you want to introduce automatic manufacturing system into the cutting process of cage motor rotor, the selections of effective cutting conditions are necessary. The cutting process of cage motor rotor requires the precision and the out of roundness of cage motor rotor. The surface roughness of cutting face. it is very important factor with effect on the magnetic flux density of cage motor rotor. The purpose of this study is to find out the effects of cutting condition. upon adapting this results, we will improve the production rate in the cutting process of cage motor rotor. As a result, the selection of cutting conditions are important factors to production rate. And these are chosen by the investigations of cutting characters and surface roughness. The experimental result, showed that the increase of cutting speed caused the decrease of cutting force and the high surface integrity. The increase of feed rate and increase of depth of cut caused the increase of cutting force and surface roughness. Thus, the effective cutting conditions of cage motor rotor by turing are cutting speed 291m/min, feed rate 0.10mm/rev, depth of cut 0.05mm.

• Geomechanics and Engineering
• /
• v.29 no.3
• /
• pp.359-368
• /
• 2022

Undercutting using an actuated disc cutter (ADC) involves more complex cutting mechanism than traditional rock cutting does, requiring the application of various new cutting parameters, such as eccentricity, cutter inclination angle, and axis rotational speed. This study presents cutting-edge laboratory-scale testing equipment that allows performing ADC tests. ADC tests were carried out on a concrete block with a specified strength of 20 MPa, using a variety of cutting settings that included penetration depth (p), eccentricity (e), and linear velocity (v). ADC, unlike pick and disc cutting, has a non-linear cutting path with a dynamic cutting direction, requiring the development of a new method for predicting cutting force and specific energy. The influence of cutting parameters to the cutter forces were discussed. The ratio of eccentricity to the penetration depth (e/p) was proposed to evaluate the optimal cutting condition. Specific energy varies with e/p ratio, and exhibits optimum values in particular cases. In general, actuated undercutting may potentially give a more efficient cutting than conventional pick and disc cutting by demonstrating reasonably lower specific energy in a comparable cutting environment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.5
• /
• pp.631-636
• /
• 2010

SNCM420 steel is one of the cam shaft materials which are used in the supply unit for ship engine cam shaft. In this study the assessment of cutting behavior was conducted for the SNCM 420 steel and SM45C steel with various cutting conditions as depth of cut 0.5, 1.0, 1.5, 2.0mm and feed rate 0.1~0.3m/rev. The controlled chip was produced in feed rate 0.2, depth of cut 1.0 for SNCM420 and feed rate 0.2, depth of cut 2.0 for SM45C. There is no difference cutting force between SM45C and SNCM420 steels.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.5 s.133
• /
• pp.38-44
• /
• 2005

Peripheral milling is one of the most important wood machining processes in wood industry. Power consumption characteristics of twelve Korean domestic species in peripheral milling were investigated in this study. Image analysis technique was applied to extract proper data from the power consumption profiles. Average power consumption increased as cutting depth increased and specific cutting power decreased as cutting depth increased. However, no significant relationship could be found between density and power consumption and between cutting depth and surface roughness.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.75-79
• /
• 1995

A cutting experiment using diamond tool was performed to make the die cabity which is composed of micro groove with mirror surface. Fine cutting depth was generated by the elastic recovery of the modified tool holder on the conventional M/C. Surface roughness and profile were investigated with cutting speed and depth and through the low cutting speed of 10mm/min, Rmax 0.005 .mu. m or less of machined surface could be achieved.

• Design & Manufacturing
• /
• v.17 no.4
• /
• pp.24-32
• /
• 2023

In this study, we introduce research aimed at minimizing machining errors without compromising productivity by compensating for the machining errors caused by tool deformation. Our approach experimentally establishes the direct correlation between cutting depth and machining error, and creates predictive models using mathematical functions. This method allows for the prediction of compensated cutting depths to obtain the desired cutting profiles, thereby maximizing the compensation of machining errors in the cutting process.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.9
• /
• pp.55-62
• /
• 2003

This paper investigates the micro-cutting of cemented carbides using PCD (polycrystalline diamond) and PCBN (polycrystalline cubic boron nitride) cutting tools are performed with SEM direct observation method. The purpose of this study is to make clear the cutting mechanism of cemented carbides and the fracture of WC particles at the plastic deformation zone in orthogonal micro-cutting. And also to achieve systematic understanding, the effect of machining parameter on chip formation and machined surface was studied, including cutting speed, depth of cut and various tool rake angle. Summary of the results are shown below. (1) Three type of chip formation process have been proposed by the results of the direct observation in orthogonal micro-cutting of cemented carbide materials. (2) From the whole observation of chip formation, primary WC particles are crushed and/or fine grained in the shearing deformation zone. A part of them are observed to collide directly with a cutting edge of tool by following the micro-cutting. (3) Surface finish, surface morphology and surface integrity is good to obtain by cutting with PCD cutting tool compared with PCBN. (4) The machined surface has the best quality near the low cutting speed of 10${\mu}m$/sec with a cutting depth of 10 ${\mu}m$ using 0$^\circ$ rake angle and 3$^\circ$ flank angle in this condition, but it was found that excessively low speed, for example the extent of 1 ${\mu}m$/sec, is not good enough to select for various reason.