• Environmental Engineering Research
• /
• v.24 no.4
• /
• pp.680-689
• /
• 2019

Temperature effects on the generation of brake wear particles from railway vehicles were generated, with a particular focus on the generation of ultrafine particles. A real scale brake dynamometer test was repeated five times under low and high initial temperatures of brake discs, respectively, to obtain generalized results. Size distributions and temporal patterns of wear particles were analyzed through visualization using clustered heatmaps. Our results indicate that high initial temperature conditions promote the generation of ultrafine particles. While particle concentration peaked within the range of fine sized particles under both low and high initial temperature, an additional peak occurred within the range of ultrafine sized particles only under high initial temperature. The timing of peak occurrence also differed between low and high initial temperature conditions. Under low initial temperature fine sized particles were generated intensively at the latter end of braking, whereas under high initial temperature both fine and ultrafine particles were generated more dispersedly along the braking period. The clustered correlation heatmap divided particle sizes into two groups, within which generation timing and concentration of particles were similar. The cut-off point between the two groups was approximately 100 nm, confirming that the governing mechanisms for the generation of fine particles and ultrafine particles are different.

• Journal of Ginseng Research
• /
• v.34 no.1
• /
• pp.23-29
• /
• 2010

This study examined the biological characteristics of the insect and examined potential cultural controls using peduncle topping methods. Ginseng stem fungus gnat eggs hatched after 5 days; ecdysis lasted 3-4 weeks, and after 5 days pupation, adults emerged. Adults deposited eggs 1-2 days after emerging, and the entire life cycle lasted 32-40 days. The fungus gnats laid eggs $327\times220{\mu}m$ in size on cut planes of stems, but not on intact stem parts that had not been topped or wounded. Analyses of major weather data for the experimental areas and weather data for the past 30 years acquired from the Korea Meteorological Administration revealed that fungus gnat dispersion was prevalent under highly humid conditions and in areas with thick and frequent fogging. Among the topping times examined, fungus gnat damage to ginseng was lowest when topping occurred in late May. Among the five different topping methods evaluated on experimental ginseng farms, the cumulative fungus gnat damage to ginseng was low (0.8%) under partial peduncle topping (removal of peduncle with lateral fruit remaining) and removal of only flower buds (0.6%), with fungus gnat control effects of 82% and 86%, respectively, compared to conventional topping (removal of peduncle about 5 cm above its base). No fungus gnat damage to ginseng was observed under the no-topping treatment. These results suggest that partial topping of peduncles, while letting lateral fruits remain, is a potentially environmentally friendly method of controlling the ginseng stem fungus gnat.

• The Journal of Fisheries Business Administration
• /
• v.33 no.2
• /
• pp.127-152
• /
• 2002

This study intends to review the development of Large Purse Seine Fisheries in Korea and Japan, and subsequent changes in the fisheries regime as well as management conditions and to examine reorganization directions. In the Northeast Asian Fishing Area, each country has done mutual operation, which causes the fishery competition and controls fishery development. Besides, Exclusive Economic Zon(EEZ) established in 1996 resulted in the prominent changes of fishery development as well as fishery relationship among each country, demands reorganization of fisheries. In the Large Purse Seine fisheries, Korea and Japan are not decreasing, they are stable. In other words, the increase in one country does not necessarily make the decrease in the other country. This is a difference from the case of the bottom fishery. Japan is the highest in the cost, the management is getting worse due to decreasing fish price and shortage of labor. In the case of Korea, the stagnant productivity has been compensated by the rising fish price, but the fishery of low productivity to cut down the size. In addition, during the 1990s the environment of fishery is getting worse because of the free import fishery, shortage of labor, etc. Following the new fisheries paradigm, each country should reorganize its fisheries structure. The principle for reorganization of fisheries structure in each country should be focused on the establishment of sustainable fisheries. The reorganization of fisheries structure for each country by EEZ establishment does not mean only dividing fishing ground and fisheries resources by countries, but means that countries should cooperate together in fisheries management for long-run benefits from fisheries.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.358-363
• /
• 2014

Adhesion forces between acrylate imprinting resin and a surface treated atomic force microscope (AFM) tip were investigated. Compared to the untreated silicon tip, 38% of the adhesion force is reduced for the hydrophobic tip treated with $CH_4$ plasma whereas 1.6 time increases is found for the hydrophilic tip with $O_2$ plasma treatment. Such a measurement of the adhesion force using AFM provides very quantitative results on adhesion comparing to the crosscut adhesion test which gives qualitative results. Since the adhesion area becomes larger as the imprinting pattern size gets smaller, the surface treatment issue becomes more important in the nano-imprinting process.

• Resources Recycling
• /
• v.24 no.4
• /
• pp.56-60
• /
• 2015

Fine particle classification was performed using products obtained from primary classification process after flotation for efficient application of tailing. The cut size increased with decreasing input pressure from 0.1 MPa to 0.3 MPa and increasing pulp density from 5% to 15% using 2-inch hydrocyclone. The median sizes of overflow and underflow were $6.56{\mu}m$ and $55.45{\mu}m$, respectively at 0.3 MPa with 5% pulp density. The imperfection became closed to ideal separation with increasing the pulp density and decreasing the input pressure. The water content decreased with increasing the pulp density, but the effect of input pressure could be ignored. The water content of underflow was 27.9% at 0.3 MPa with 15% pulp density.

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.45-52
• /
• 2018

In this study, 398 city gas pipe systems installed on the bridges were surveyed and analyzed classified characteristics about the ages, length, and remote isolation devices installed or not. As a result of analysis, 43.0% pipes have been used more than 20 years and 89.4% do not have remote cut-off devices, so this study suggest safety management ways for the issues. Chosen 76 pipes were researched stress strain characteristics by CAESAR-II which is a specialized program for stress analysis. And, when a loop is installed on the bridge pipe, effect on code stress by the location and size of the loop was performed. This study can help to improve safety level by revising criteria of new installation, inspection and diagnostic.

• Journal of the Korean Institute of Gas
• /
• v.22 no.1
• /
• pp.60-63
• /
• 2018

This paper presents the FEM analysis results on the strength safety of a gas valve for a LPG cylinder. Based on the FEM analysis, the maximum von Mises stress on the boundary zone between a safety valve and the upper area of the thread is 99.2 MPa for the supplied gas pressure of 3.5 MPa in which the gas valve is fully opened. The maximum von Mises stress of 99.2 MPa is considered as safety value, because that value is lower than the yield stress of a brass material. In this case, the maximum deformation at the upper right part of the pressure regulator is 0.002mm. The maximum deformation zone is not a meaning part of the sealing part such as an O-ring or a diaphragm of a gas valve and a pressure regulator. The proposed hybrid gas valve model in which is integrated with a conventional cut-off valve and a pressure regulator is recommended as a gas leakage free mechanism and minimized compact size for a LPG cylinder.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.1
• /
• pp.23-28
• /
• 1999

Rectangular waveguide slot antenna which has simple structure, high efficiency, high trust and small size, is extending in a field of application such as many Radar and Microwave communication. A slot cut into a wall of waveguide is propagated electromagnetic wave to free space it interrtupts the flow of current inner conductor of waveguide. Therefore incident of slot, cutdepth, width, length, i.e. are important parameter of characteristic change of the slot antenna. Result from difficulty of theoretical analysis about slot frequently experimental measured data useful design and manufacture have been accomplished. In this paper, we find the suitable method of analysis that compare two analysis results with measured result of established literature - admittance of slot be solved by propagated power from electric field distribution of slot and mode current computation and accomplishment of computable chart which hasresonant length and cutdepth, incident of slot, i.e. and use the HFSS which applyed finite-element method obtain equal slot analyed method.

• Journal of Biosystems Engineering
• /
• v.35 no.6
• /
• pp.373-379
• /
• 2010

This study was carried out to develop a belt pick-up type one-row soybean cutter, using physical properties and production conditions of soybeans. The prototype soybean cutter consisted of 4 parts: cutting part, conveying part, collecting part, and travelling part. The prototype soybean cutter was designed to cut soybeans planted with a row spacing of 600 mm, and at a height of 30 mm from the bed bottom using a disk saw. Through various trials with different peripheral velocities of the disk saw and forward speed of the cutter, determined ranges of the peripheral velocity of the disk saw cutting soybeans stems were greater than 18.3 m/s. Spacing between pick-up belts (clearance) was in a range of 60~90 mm so that soybeans could be picked at heights greater than 25 cm, and the size and shape of the pick-up belt were determined the conventional manual harvesting method. The optimal ratio between the forward speed of cutter and the peripheral speed of pick-up belts were from 1 to 1.2 by theoretical analysis. the pick-up belts had a $35^{\circ}$ of tilted angle and $90^{\circ}$ of twisted angle to pick up soybeans safely from the plant input to the lower end of the belts and convey soybeans to the upper end of belts nearby a container. The soybeans at the rear container were dropped down on the soybean row with an interval. The effective field capacity of the prototype soybean cutter was 0.136 ha/h, reducing the working hour by 92% when compared with the manual cutting.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.6
• /
• pp.22-29
• /
• 2002

The conventional neon transformer systems are very bulky and heavy because it consist of leakage type transformers made of silicon steel plates. In addition, it has problems in noise by a neon transformer and in possibilities of fire and electrical shock when neon tubes are destroyed. A protection circuit is designed for all types of neon transformer loaded with one or more neon tubes. Whenever the neon tube fails to be started up, comes to the life end, encounters faults with open-circuits at the output terminals of the neon transformer, the protection circuit will be initiated to avoid more critical hazards. The input of the transformer is automatically cut off when the abnormal condition occurs, preventing waste of no-load power. To improve such problems, in this paper, a new type of neon power supply systems for neon tube is designed and implemented using inverter type circuits and a newly designed lightweight transformer. In the developed neon transformer system, a 60［Hz］power input is converted to 20［KHz］high frequency using half-wave inverters, thereby the transformer reduces its size by 1/5 in volume and 1/10 in weight.