• Journal of Korean Association for Spatial Structures
• /
• v.18 no.1
• /
• pp.93-100
• /
• 2018

The retractable roof structures have actions of various types of loads and external forces depending on the retraction and operation conditions of the roof in terms of efficiency of control and maintenance as the aspect of structural plan. In particular, there is a need for studies on the establishment of retraction controlled wind velocity to maintain the stable control and usability of roof structure against strong winds or sudden gusts during the retraction of the roof. In this paper, it was intended to provide basic materials for the development of guidelines on the operation and maintenance of domestic retractable buildings with large space by analyzing the factors affecting the retraction controlled wind velocity for the overseas stadiums with the large spatial retractable roof structures where the sliding system was applied on the steel retractable systems. As a result, the controlled wind velocity tends to decrease as the retractable roof area increases. On the other hand, the controlled wind velocity tends to increase as the retraction time increases. In addition, in the space-grid roof structures, the spherical roof structures type showed the average controlled wind velocity of 10m/sec lower than that of 17.3m/sec for curved-roof structure type, and in the curved-roof structure type, the truss roof structure showed the average controlled wind velocity of 8.9m/sec which is lower than that of 17.3m/sec for the space for the space-grid roof structure.

• Journal of the Institute of Convergence Signal Processing
• /
• v.22 no.3
• /
• pp.116-121
• /
• 2021

A lot of research is being done to develop a high-efficiency heat pump to save energy, and research to reduce or eliminate the phenomenon of frost occurring in the outdoor unit coil is also being conducted at the same time. A curved constant temperature chamber was constructed that can be tested under the same conditions as in the natural state so that the research can be conducted in which frost does not occur on the outdoor unit of the heat pump regardless of the season. Simulations were performed to verity whether such a curved constant temperature chamber has feasibility as an experimental device. For CFD conditions, the length of the straight duct in front of the outdoor unit located in the duct-type constant temperature chamber was 1, 5, 10 and 15 times the diameter of the duct. As a result, it was found that a straight space must be secured 10 times the diameter of the duct.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.3
• /
• pp.195-206
• /
• 2011

The capacity spectrum method(CSM) has been more frequently used as a tool to evaluate the seismic capacity of the structure. Many formulas of strength reduction factors(SRF) have been proposed and adopted to generate the inelastic demand spectrum for the CSM. This study evaluates the impacts of the type of the SRF on the inelastic demand spectrum and finally on the seismic response displacement of curved bridge. For the purpose, the several existing formulas of SRFs were comparatively investigated through the case study. Curved bridges with different subtended angles were selected and the displacements of the bridge piers were estimated by using the different formulas of SRFs. Nonlinear time history analyses were also performed for the validation purpose of the CSM results. According to study results, the CSM may generate the larger displacement responses than the actual behaviors for the curved bridge with larger subtended angles. Though many methods have been suggested to generate the inelastic demand spectrum for CSM, they might not give noticeable differences in inelastic displacement of the bridge pier.

• The KSFM Journal of Fluid Machinery
• /
• v.1 no.1 s.1
• /
• pp.81-89
• /
• 1998

In this study, the effects of the impeller shapes on the pump performances of the non-clogging and the screw-type centrifugal pumps are experimentally studied. The characteristics of total head, efficiency and power of the non-clogging pump increase as the number of vanes increases. The screw-type centrifugal pump with the linear-shape vane shows a little better performance than that of the screw-type centrifugal pump with the curved-shape vane. The differences in the characteristics of total head, efficiency and power are, however, insignificant. Therefore, it is advisable that, considering the convenience of pump manufacturing, the screw-type centrifugal pump with the linear-shape vane should be used. This study also compares the pump characteristics of the non-clogging pump and screw-type centrifugal pump. The characteristics of total head and efficiency of the non-clogging pump are better than those of the screw-type centrifugal pump. The screw-type centrifugal pump requires more shaft power than the non-clogging pump.

• Applied Microscopy
• /
• v.27 no.2
• /
• pp.155-163
• /
• 1997

Ultrastructural and histochemical studies were carried out on the prostate gland of a Korean slug (Incilaria fruhstorferi) with light and electron microscopes. The results are as follows. The endothelial tissue of the prostate gland is constituted with tall and narrow ciliated columnar cells, irregularly shaped cells and gland cells in which are included the elongated oval or ellipsoid nucleus those are surrounded by curved membrane. The endothelial tissue of the prostate gland is composed by type-A, B, C and type-D gland cells, and the glanules of type-A, B, and D gland cells are certified to neutral mucopolysaccharide because are related by PAS-alcian blue (pH 2.5) , but the other hand type-C gland cell is only weakly reacted to PAS, but strongly reacted by Million reaction. The glanules of type-A gland cell are small size (about $0.4{\mu}m$) and are seen high electron density, but the glanules of type-B gland cell are large size (about $0.7{\mu}m$) and glanule density is same type-A glanules. Long ellipsoid type-C gland cell contained round nucleus which is well developed beterochromatin in, and that small oval glanules (size, about $0.9{\mu}m$) of moderate high electron density which are formed a group of large glanule together with $4\sim5ea$, but type-D gland cell possessed round small nucleus are seen high electron dense glanules (size, $0.8{\mu}m$).

• The Korean Journal of Malacology
• /
• v.27 no.2
• /
• pp.149-157
• /
• 2011

Some characteristics of the formations of acrosomal vesicles during the late stage of spermatids during spermiogenesis and taxonomical charateristics of sperm morphology in male two species (Saxidomus purpurata and Meretrix petechialis) in the family Veneridae were investigated by electron microscope observations. In two species, the morphologies of the spermatozoa have the primitive type and are similar to those of other bivalves in that it contains a short midpiece with five mitochondria surrounding the centrioles. The morphologies of the sperm nuclear types of S. purpurata and M. petechialis in Veneridae have the curved cylindrical and cylinderical type, respectively. And the acrosome shapes of two species are the same cap-shape type. In particular, the axial filament is not found in the lumen of the acrosome of two species, however, subacrosomal material are observed in the subacrosomal spaces between the anterior nuclear fossa and the acrosomal vesicle of two species. The spermatozoon of S. purpurata is approximately 46-$52{\mu}m$ in length, including a curved sperm nucleus (about $3.75{\mu}m$ in length), a long acrosome (about $0.40{\mu}m$ in length),and a tail flagellum (about 45-$47{\mu}m$ long). And the spermatozoon of M. petechialis is approximately 47-$50{\mu}m$ in length including a slightly curved sperm nucleus (about $1.50{\mu}m$ in length), an acrosome (about $0.56{\mu}m$ in length) and tail flagellum (44-$48{\mu}m$ in length). In two species, the axoneme of the sperm tail flagellum of each species consists of nine pairs of microtubules at the periphery and a pair of cental doublets at the center. Therefore, the axoneme of the sperm tail flagellum shows a 9 + 2 structure. In particular, taxonomically important some charateristics of sperm morphologies of two species in the family Veneridae are acrosomal morphology of the sperm, The axial filament is not found in the acrosome as seen in a few species of the family Veneridae in the subclass Heterodonta. The acrosomal vesicle is composed of right, left basal rings and the apex part of the acrosomal vesicle. In particular, right and left basal rings show electron opaque part (region), while the apex part of the acrosomal vesicle shows electron lucent part (region). These charateristics belong to the subclass Heterodonta, unlikely a characteristic of the subclass Pteriomorphia showing all part of the acrosome being composed of electron opaque part (region). Therefore, it is easy to distinguish the families or the subclasses by the acrosomal structures. The number of mitochondria in the midpiece of the sperm of S. purpurata and M. petechialis in Veneridae are five. However, the number of mitochondria in the midpiece of the sperm in most species of Veneridae in the subclass Heterodonta are four. Therefore, the number of mitochondria of the sperm midpiece of two species are exceptionally 5, and it is only exceptional case in the species in Veneridae in the subclass Heterodonta. Except these cases, the number of mitochondria in the sperm midpiece in all families in the subclass Heterodontaare are 4, and now widely used in taxonomic analyses.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.3 no.2
• /
• pp.66-73
• /
• 2008

The pipes have been laid underground while the industry is developing. We have to take maintenance procedure when the pipes are cracked or ruptured. It is very difficult jop to check pipe's crack because the pipes are narrow and laid underground. Using in-pipe robot, we can check the conditions of inner section of pipes, therefore, we designed a crawler type robot to search cracked pipe. In this paper, we have made a special focus on the control of the robot using differential drive algorithm to move in curved section of pipes. The detailed design of the robot with experimental result show the effectiveness of the robot in pipe maintenance.

• The Journal of the Korean dental association
• /
• v.11 no.11
• /
• pp.735-737
• /
• 1973

This study is to determine the exact position of tipping rotation center of root. The method of measurement is to record by means of dial gauge. The different shapes of root of lower second premolar are named as smooth type, tapered type, and curved type. The followings are the result ; 1. The tipping rotation center of the teeth varies with he shape of roots. 2. The rotation center of the root is placed apical one third portion upon roots in the smooth shape of roots, one half portion of roots in the taper shape of roots and below the apical one-third of root in curve shape.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.99.3-99
• /
• 2001

In fluorescence mode confocal scanning microscope, level of detected signal is very low. In object scanning type confocal scanning microscope, the additional optical system with objective lens and plane mirror was proposed to increase signal intensity, but there was none for beam scanning type confocal scanning microscope. We propose reflecting optical systems which improve signal intensity in beam scanning type confocal scanning microscope. We choose one of the proposed optical systems and design the optical system, i.e., select optical components and assign distances between the selected components. To design the optical system, we use finite ray tracing method and make cost function to be minimized.

• Journal of the Korean Home Economics Association
• /
• v.20 no.3
• /
• pp.1-8
• /
• 1982

In this study, we attempted to make an original pattern of clothing for an abnormal type of figure, especially for the type of kyphosis. We measured the curvature of the spine of a woman with kyphosis with a Martin measuring instrument and a silhouetter in the following ways. First, we counted the rate of shrinkage of the standard lines drawn on the surface of the body according as the body moved. Secondly, placing the front and back darts, the front and back shoulder darts and the side darts according to“Munhwa”pattern, we made cubic cuttings of four moving postures as well as the standing one. Thirdly, we superposed the developed patterns of the standing and the moving postures, measuring the position change and the amount to the change of the darts, and compared them. The results are as follows: 1) In the developed pattern of a cubic cutting of the basic pattern and the standing posture, the neckhole became larger than that of the basic pattern, and the waist line was lowered than that of the basic pattern because the center back line was shortened due to the curved backbone.