• Fashion & Textile Research Journal
• /
• v.13 no.5
• /
• pp.661-671
• /
• 2011

This study was designed to produce rounded belt pattern and tight-skirt pattern drafting method using 3D body scan data. Subjects were thirty women in their early twenties. In order to figure out the optimum cutting points, namely, where darts are made, using CAD program, curve ratio inflection points on the horizontal curve of waist, abdomen, and hip to find 1 point in the front, two points in the back part. The average length from center front point to maximum curve ratio was 7.7 cm(46.3%) on the waist curve; 7.9 cm(39.4%) on the abdomen curve. And the average length from center back point to maximum curve ratio point was 6.9 cm(39.0%) for first dart and 11.2 cm(63.3%) for second dart on the waist curve; 8.9 cm(35.8%) for first dart and 15.7 cm(63.3%) for second dart on the hip curve respectively. The cutting lines from were made up by connecting curve inflection points. After divided using cutting lines, each patch was flattened onto the plane and all the technical design factors related with patternmaking were measured, such as dart amount, lifting amount of side waist point, etc. Based on the results of correlation analysis among these factors, regression analysis was done to produce equations to estimate the variables necessary to draw up pattern draft method; F1=F8+1.1, $F4=2.5{\times}F2+0.9$, $F5=0.9{\times}F4+1.0$, $F6=0.3{\times}F4+0.4$, $B1=0.9{\times}B8+2.3$, $B4=2.1{\times}B2+1.3$, $B5=0.9{\times}B4+3.5$, and $B6=0.3{\times}B4+0.4$.

• Fashion & Textile Research Journal
• /
• v.12 no.4
• /
• pp.467-476
• /
• 2010

The purpose of this study was to develop a plausible methodology based on experimental data how to set up darts and split lines on 3D parametric body dressed with tight-fit garment. The results were as following: Through the process of making convex hull, the concave parts were straightened to make a convex hull, especially in the center part of bust, under breast part and scapular part. To figure out the optimum positions of darts and split lines, the inflection points of curve ratio were searched along the horizontal polylines of waist and bust. This procedures produced reliable results with low deviation. Using Rapidform, CATIA and Unigraphics, six patches of bodice patterns were drawn and aligned. Paired t-test results showed the outline and area between 3D surface and 2D were not significantly different, meaning this method could be adaptable when flattening 3D surfaces. The amount of waist dart measured on the pattern showed that the highest portion was allocated on 2nd dart(back), followed by 1st dart(back), 1st dart(front), 2nd dart(front)/side dart, and center back dart. A series of findings suggested that curve ration inflection point could be used as a guide to set up darts and split line on 3D parametric model with low deviation.

• Journal of Animal Science and Technology
• /
• v.54 no.6
• /
• pp.395-400
• /
• 2012

This study was conducted to estimate the growth curve parameters for the body weight (BW) and body length (BL) of miniature pigs in Korea. Growth curve parameters were estimated through a nonlinear regression model using Gompertz, Logistic, and von Bertalanffy methods. A total of 25 piglets were measured monthly from birth up to 15 months of age to estimate both body weight and length. Results showed that the estimated average values for the body weight (body length) were 31.83 kg (58.77 cm) for the mature weight (A), 3.06 (1.74) for the growth ratio (${\beta}$), and 0.28 (0.52) for the maturing rate (${\kappa}$). Average inflection points showing maximum growth rate estimated each month for body weight were 3.97 kg and 11.70 cm, while for the body length were 1.06 kg and 21.61 cm. Moreover, the estimated maturation rates of the body weight and length for the group of Sire 1 were 0.22 and 0.40 respectively, whereas for the group of Sire 2 these values were 0.34 and 0.39. On the other hand, for the groups of Dam 1, Dam 2, and Dam 3, maturation rates for their body weights were 0.26, 0.28 and 0.33 respectively, while for their body lengths these values were 0.43, 0.37, and 0.38, respectively. The study also indicated a negative relationship between the values of mature weight and maturity rate for the body weight will result to a higher inflection point which is in contrast for the body length where results show that a positive relationship between the values of mature length and the maturity rate will result to a higher inflection point. Furthermore, the growth performance of miniature pig varies across stages but using these estimated growth curve parameters could improve the genetic traits of miniature pig.

• Journal of Korean Association for Spatial Structures
• /
• v.6 no.2 s.20
• /
• pp.93-105
• /
• 2006

In order to investigate the effect of the height of application point of lateral loads and reinforcing steel bars in walls and columns in improving the seismic behavior of confined concrete block masonry walls, an experimental research program is conducted. A total of twelve one-half scale specimens are tested under repeated lateral loads. Specimens are tested to failure with increasing maximum lateral drifts while a vertical axial load was applied and maintained constant. The specimens adopted are two-dimensional (2D) hollow concrete block masonry walls with different parameters such as shear span ratio, inflection point and percent of reinforcement in confining columns and walls. Test results obtained for each specimen include cracking patterns, load-deflection curve, and strains in reinforcement and walls in critical locations. Analysis of test data showed that above parameters generate a considerable effect on the seismic performance of confined concrete block masonry walls.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1935-1946
• /
• 2013

In this study, the behavior characteristics of bent pile structures with varying cross-section was examined through the measured results of field load test. A framework for determining the bending stress is calculated based on the stresses in the circumference of the pile using 3D finite element analysis. It is found that the bending stress near the pile-column joint changes rapidly and fracture zones occurs easily at variable cross-sections in bent pile structures. Also, the optimized column-pile diameter ratio was analyzed through the relationship between the column-pile diameter ratio and lateral crack load ratio. Based on this study, the optimized column-pile diameter ratio can be obtained near the inflection point of the curve between the column-pile diameter ratio and lateral crack load ratio. Therefore, a present study by considering the optimized variable cross-section condition would be improved bent pile structures design.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.349-356
• /
• 2010

In this study, a new design method of pile bent structure considering plastic hinge was proposed on the basis of the beam-column model. Based on the analysis results, it is found that the positioning of plastic hinge on the pile bent structure was influenced by nonlinear behavior of material and p-$\Delta$ effect. Moreover, concrete cracking began to occur at the joint section between the pile and column in case of pile bent structure with different cross-sections. The plastic hinge can be developed on the pile bent structure when large displacement was occurred, and pile bent structures can be maintained well only if it is developed on the column part. Therefore, in this study, the optimized cross-section ratio between column and pile was analyzed to induce the plastic hinge at the joint section between the pile and column. Based on this, the optimized diameter ratio of pile and column can be obtained below the inflection point of the bi-linear curve depending on the relations between column-pile diameter ratio($D_c/D_p$) and normalized lateral cracking load ratio($F/F_{Dc=Dp}$). And through this study, it is founded that in-depth limit($L_{As}$=0.4%) normalized by the pile length($L_P$) are proportionally decreased as the pile length($L_P/D_P$) increases up to $L_P/D_P$=17.5, and beyond that in-depth limit converges to a constant value. Finally, it is found that the proposed limit depth by taking into account the minimum concrete-steel ratio would be more economical design of the pile bent structure.

• Elastomers and Composites
• /
• v.6 no.1
• /
• pp.71-81
• /
• 1971

The intention of this study is to investigate the properties of polymer blend, NBR/PVC vulcanizates and blending procedures such as roll-mixing temperatures and sequences for polymer blending of NBR and PVC(resin type). The results obtained are as follows: 1. The roll temperature applied for polymer blending is around $150^{\circ}C$. At this temperature region, the degradation of rubber stock, which may be caused by heat, can be minimized and mill processing in practical application in industries can also be facilitated. 2. It is obviously necessary that a small amount of plasticizers should be added to the stock for improving processibility of roll mixing and physical properties. 3. On roll-mixing sequence, it is more effective that PVC compounded with plasticizer is added to NBR milled on hot roll. 4. The vulcanizates of the blends with different degree of polymerization of PVC ale similar to one another in properties. 5. NBR/PVC(70/30) blends shows the better physical characters than eve,-made foreign latex blend except abrasion-resistance. 6. As PVC addition ratio is increased, the physical properties such as resistance to ozone, tear, heat and oil and tensile strength, modulus, hardness have also improved, on the other hand, tension set and rebound character decreased. 7. The curve of ultimate elongation have point of inflection at the ratio of $30\sim40$ part of PVC. 8. While CR is blended, the physical properties such as brittle point, rebound and resistance to oil in high temperature have improved. 9. Polymer blend of NBR and domestic PVC is applied for the industrial utility such as rubber sole and heel, electric wire cover and oil-resistant packing, coating and gasket, printing roll, film for food packing etc.

• Korean Journal of Poultry Science
• /
• v.49 no.4
• /
• pp.229-237
• /
• 2022

This study investigated the growth characteristics of four strains of newly developed synthetic Korean native commercial chickens (KNCs). We investigated a suitable growth curve model in KNCs and estimated the number of days to reach a 2 kg market weight. Body weight was measured at 2-week intervals from birth to 12 weeks of age. The growth curves were estimated using von Berteralanffy, Gompertz, and logistic functions. The results showed that males were significantly heavier than females at all ages, but there were no significant differences in body weight between strains, except at birth and 2 and 6 weeks of age. The coefficients of determination and adjusted determination of growth function had high goodness-of-fit (97.4~99.7). Of the growth curve parameters, the mature weight and growth ratio were higher in males than in females, but the maturity rate was similar in males and females. The inflection point occurred at approximately 7 weeks of age for females and 8 to 9 weeks of age for males. The weights estimated from the growth curve functions almost agreed with the actual weights, except for male weights estimated using the von Bertalanffy function. The coefficients of determination of the regression equations for weight to age were 0.9583 to 0.9746. The 8- and 10-week-old body weights estimated using the regression equation, and the 12-week-old weight estimated using the logistic function were most similar to the actual weight. Using these models, the estimated age of KNCs to reach 2 kg was 62.0~64.6 days for males and 74.9~78.6 days for females.

• Journal of the Korea Concrete Institute
• /
• v.28 no.1
• /
• pp.13-21
• /
• 2016

A hybrid precast concrete beam system with a simple rigid connection was proposed to compensate the limitations and shortcomings of the conventional bolt connection associated with the H-beams embedded into concrete beams. Three beam specimens with fixed both ends were tested under one-point top cyclic loading to explore the effectiveness of the developed hybrid beam system in transferring externally applied flexure to a column. The main parameter considered was the length ($L_s$) of H-beam, which was selected to be $0.25L_I$, $0.5L_I$, and $1.0L_I$, where $L_I$ is the distance from the support to the point of inflection. All beam specimens showed a better displacement ductility ratio than the reinforced concrete beams with the same longitudinal reinforcement index, indicating that the cyclic load-deflection curve and ductility were insignificantly affected by $L_s$. The continuous strain distribution along the beam length and the prediction of the ultimate load based on the collapse mechanism ascertained the structural adequacy of the developed rigid connection.

• Korean Journal of Agricultural Science
• /
• v.10 no.1
• /
• pp.110-117
• /
• 1983

This study was conducted to investigate the influence of load increment ratio on the secondary consolidation for the marine clay at Asan bay by the hyperbola method. The results were summarized as follow: 1. Calculated secondary consolidation by the hyperbola method was slightly less than the value of Casagrande's log t method, but the difference was very little, and the secondary consolidation could be easily calculated by the hyperbola method even if load increment ratio was small. 2. The secondary consolidation ratio was increased with the decrement of load increment ratio, and the creep phenomenon of the settlement curve occurred under the condition of small load increment ratio seemed to be caused by the secondary consolidation. 3. The secondary consolidation ratio occurred during the primary consolidation was irregular in the overconsolidated range, but it was increased with the decrement of load increment ratio in the normally consolidated range. 4. The coefficient of secondary consolidation was increased with the increment of the consolidation load, made a point of the inflection near preconsolidation. And the coefficient of secondary consolidation was decreased from consolidation load $2kg/cm^2$, showed independent of load increment ratio. 5. The coefficient of secondary consolidation was showed in proportion to compression index.