• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.422-425
• /
• 2006

본 연구는 도체주변에 감겨진 광섬유 코일에 따라 선형편광축이 자기장에 의해 회전하는 Faraday Effect를 이용한 GIS(Gas Insulated Switchgear,이하 GIS) 용 광 전류센서의 구성과 DAQ(Data Acquisition,이하 DAQ)보드를 장착한 PC를 이용하여 실시간 데이터 취득, 분석 그리고 저장을 동시에 수행하였다 광원은 1310[nm]의 레이저 다이오드를 이용하였다. 센서부는 GIS에 맞게 원형으로 제작하였고 $9/125[{\mu}m]$규격 단일모드의 일반 통신용 광섬유를 지름 31[cm]의 센서부 코어에 20[회] 감아 설치하였다. PC기반의 실시간 데이터 분석 프로그래밍은 NI사의 Labview를 이용하여 코딩하였으며 PD(Photo Diode,이하 PD)의 전기적인 신호는 터미널 블록을 거쳐 NI사의 16bit DAQ M시리즈를 이용하여 수집되어진다. 직접 코딩한 프로그램을 이용하여 $700A\sim1400A$ 측정한 출력값 선형적인 증가추세를 보여주었다. 또한 OCS(Oscilloscope,이하 OCS)를 이용한 측정시스템과의 출력신호 및 정밀도를 비교 검토하였다. 그리고 Labview에서 지원하는 Web Tool기능을 이용하여 Web기반의 원거리 측정에서도 안정된 출력을 보여주었다.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.516-517
• /
• 2015

This paper proposes the feedforward compensation method of output voltage with 3phase AC/DC PWM converter on DC distribution system for improved response. AC/DC PWM converter on DC distribution is required power supply of high quality because of renewable energy sources and load links. In general, Feedforward compensation method of 3phase AC/DC PWM converter receives the sensor input to the output current, load power. Resulting, error of the sensing values and communication cause time delay. Therefore, Feedforward compensation method through only the output voltage is proposed in this paper. The feedforward compensation method through only the output voltage can be applied to the two-level AC/DC PWM converters, as well as multi-level converter or inverter.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1406-1408
• /
• 2003

KOMPSAT-1 (KOrea Multi-Purpose SATellite ? 1) EOC (Electro Optic Camera) raw images are radiometrically corrected on ground based on the characteristics of EOC. They consist of each CCD (Charge?Coupled Device) pixel’s calibration slope which was measured on ground, electrical gains which are applied to amplify for increasing output pixel counts. Currently, radio-metrically corrected EOC images with calibration slope have still shown defective features by residual stripes. So, it should be compensated by adjusting the calibration slope. In this paper, the adjustment of current calibration slope for de-striping EOC images is addressed and test results are shown.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.1246-1248
• /
• 2003

Internal wave with a soliton-like, large amplitudes within several kilometers, is frequently observed in the sea surface caused by tidal rectification due to sill or rough topographic changes. Internal waves can perturb current and density field, initiate bottom sediment re -suspension and mix nutrients to photic zone. Previous studies indicate that the appearance of internal wave in the Lombok Strait have been detected in SAR image data. This paper studies effect of internal wave in the Lombok Strait to chlorophyll distribution in the surrounded areas using SeaWiFS and ERS SAR images data during 1996-2001 periods. The preliminary result concludes that the internal waves presumably affect phytoplankton distribution spreading southeastward in the coast off Bali Island. The distribution of phytoplankton at southern coastline off Bali Island when internal wave occurred is elongated and distributed further to westward (from 8.8$^{\circ}$ to 10.7$^{\circ}$LS) than the area when internal wave did not occur on August 2000 (from 9.25$^{\circ}$ to 10.25$^{\circ}$LS) as shown in figure 3. It shown that the surface phytoplankton concentration near coastal area, i.e. from 8.8$^{\circ}$ to 9.25$^{\circ}$ LS, increased when internal wave is occurred.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.618-620
• /
• 2003

Harmonics of sea surface temperature (SST) in the East Sea and their possible causes are examined by analyzing NOAA/AVHRR data, SSM/I wind speeds, NSCAT wind vectors, and NCEP heat flux data. Detailed spatial structures of amplitudes and phases of the seasonal cycles and their contributions to the total variance of SST have quantitatively. The Subpolar front serves as a boundary between regions of high annual amplitudes (${\geq}$10$^{\circ}$C) in the cold continental region and low amplitudes (${\leq}$10$^{\circ}$C) in the Tsushima Warm Current region. The low phase center of annual cycle is located over a seamount at 132.2$^{\circ}$E, 41.7$^{\circ}$N south of Vladivostok. Semi-annual amplitudes are significantly large leaching over 20% of the annual amplitudes in the Tatarskiy Strait and along the continental shelf off Russian coast in fall and spring, but its forcings are substantially annual. We have shown that fall cooling is attributed by direct and local wind forcing, while spring cooling is remotely forced by cold waters from sea ices in the Tatarskiy Strait.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.189-191
• /
• 2003

The types of service using location information are being various and extending its domain as wireless internet technology is developing and its application part is widespread, so it is prospected that LBS (Location-Based Services) will be killer application in wireless internet services. The MODB (Moving Object Database) stores and manages very large current/ past moving object data, so it is very important part in LBS platform. The performance of LBS platform is tightly depending on the performance of this MODB. The other important part is alerting engine in LBS platform, which is system to transmit various value-added information or notify emergency information to mobile phone after triggering specified events. This alert engine is supported as extended function of MODB, that is to say, the alerting function is closely related with MODB. So alert cartridge on MODB must provide not only moving point triggering about going into, going out specified geographical area but also batch alerting about nearest neighbor from specified geographical area. In this paper, we study of extended part on MODB to support the alert engine. And we design alert engine cartridge on MODB before implementing the system.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.301-303
• /
• 2003

The extraction of 3D road network from high-resolution aerial images is still one of the current challenges in digital photogrammetry and computer vision. For many years, there are many researcher groups working for this task, but unt il now, there are no papers for doing this with TLS (Three linear scanner), which has been developed for the past several years, and has very high-resolution (about 3 cm in ground resolution). In this paper, we present a methodology of road extraction from high-resolution digital imagery taken over urban areas using this modern photogrammetry’s scanner (TLS). The key features of the approach are: (1) Because of high resolution of TLS image, our extraction method is especially designed for constructing 3D road map for next -generation digital navigation map; (2) for extracting road, we use the global context of the intensity variations associated with different features of road (i.e. zebra line and center line), prior to any local edge. So extraction can become comparatively easy, because we can use different special edge detector according different features. The results achieved with our approach show that it is possible and economic to extract 3D road data from Three Linear Scanner to construct next -generation digital navigation road map.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2184-2186
• /
• 2001

The research presented in this paper focuses on a method for the detection of High Impedance Fault(HIF). The method will use the fast wavelet transform and neural network system. HIF on the multi-grounded three-phase four-wires primary distribution power system cannot be detected effectively by existing over current sensing devices. These paper describes the application of fast wavelet transform to the various HIF data. These data were measured in actual 22.9kV distribution system. Wavelet transform analysis gives the frequency and time-scale information. The neural network system as a fault detector was trained to discriminate HIF from the normal status by a gradient descent method. The proposed method performed very well by proving the right state when it was applied staged fault data and normal load mimics HIF, such as arc-welder.

• Korean Journal of Chemical Engineering
• /
• v.35 no.12
• /
• pp.2421-2429
• /
• 2018

Thiol-based self-assembled anchor linked to glucose oxidase (GOx) and gold nanoparticle (GNP) cluster is suggested to enhance the performance of glucose biosensor. By the adoption of thiol-based anchors, the activity of biocatalyst consisting of GOx, GNP, polyethyleneimine (PEI) and carbon nanotube (CNT) is improved because they play a crucial role in preventing the leaching out of GOx. They also promote electron collection and transfer, and this is due to a strong hydrophobic interaction between the active site of GOx and the aromatic ring of anchor, while the effect is optimized with the use of thiophenol anchor due to its simple configuration. Based on that, it is quantified that by the adoption of thiophenol as anchor, the current density of flavin adenine dinucleotide (FAD) redox reaction increases about 42%, electron transfer rate constant ($k_s$) is $9.1{\pm}0.1s^{-1}$ and the value is 26% higher than that of catalyst that does not use the anchor structure.

• Smart Structures and Systems
• /
• v.7 no.5
• /
• pp.365-378
• /
• 2011

Piezo-based active structural health monitoring (SHM) requires amplifiers specifically designed for capacitive loads. Moreover, with the increase in number of applications of wireless SHM systems, energy efficiency and cost reduction for this type of amplifiers is becoming a requirement. General lab grade amplifiers are big and costly, and not built for outdoor environments. Although some piezoceramic power amplifiers are available in the market, none of them are specifically targeting the wireless constraints and low power requirements. In this paper, a piezoceramic transducer amplifier for wireless active SHM systems has been designed. Power requirements are met by two digital On/Off switches that set the amplifier in a standby state when not in use. It provides a stable ${\pm}180$ Volts output with a bandwidth of 7k Hz using a single 12 V battery. Additionally, both voltage and current outputs are provided for feedback control, impedance check, or actuator damage verification. Vibration control tests of an aluminum beam were conducted in the University of Houston lab, while wireless active SHM tests of a wind turbine blade were performed in the Harbin Institute of Technology wind tunnel. The results showed that the developed amplifier provided equivalent results to commercial solutions in suppressing structural vibrations, and that it allows researchers to perform active wireless SHM on moving objects with no power wires from the grid.