• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.1
• /
• pp.72-80
• /
• 2019

In this paper, we propose a digital DC-Link current control approach for BLDC actuation systems. The proposed approach consists of the following two components: first, DC-Link current measurement with sampling instances synchronized with PWM frequency, and second, current control using single DC-Link current rather than three phases current of a motor. The proposed method proved its performance through experiments and simulation. The results showed that the control performance are increased compared with the BLDC actuation system which does not use current control.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.5 no.4
• /
• pp.335-342
• /
• 2000

A new control method for a single-phase active power filter, based on a load current estimation using a DC capacitor voltage of active power filter without sensing nonlinear load current, is proposed in this paper. Because the method proposed can remove the load current sensor in comparison with a conventional method sensing the load current and DC capacitor voltage together, it can make the active power filter easy installation, low cost, small size with no performance detriment. In addition, sample-hold technique and proportional control method is adopted to control the DC capacitor voltage and as no delay element such as LPF or PI control in the conventional method is used, the transient response is fast and good. Operation of a single-phase active power filter which consist of eight mode is explained according to utility voltage, compensation current and switch state, and compensation characteristics of active power filter using proposed method is verified by experiment.

• Korean Journal of Remote Sensing
• /
• v.16 no.3
• /
• pp.199-209
• /
• 2000

This study improves the feature tracking method (FTM) in estimating the ocean current vectors from the sequential AVHRR satellite imageries by adding the objective algorithm in defining the edges and boundaries of the oceanic eddies and fronts. It was implemented by using the Sobel operator. The Sobel operator has been proved to be in effective filter in detecting the edges of any object on the image. In estimating the current vectors on the edges defined by the Sobel operator, center coordinates of the Pattern and Search tiles need to be determined by the investigator. The objective feature tracking method combined with maximum cross correlation method (MCC) is turned out to be very efficient and fast, since it uses only parts of the image containing the objects instead of searching the entire image. In the validation with the in situ ADCP measurements of currents in the East Sea, the estimated current speed values are around 35% lower than and current directions are deviated by $34^{\circ}$ from ADCP current vectors. The results are regarded as improved ones compared to the previous investigators'.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.9
• /
• pp.2577-2582
• /
• 2013

A novel stick-shaped portable sensing device featuring a microhole array interface between the polyvinylchloride-2-nitrophenyloctylether (PVC-NPOE) gel and water phase was developed for in-situ sensing of perchlorate ions in real water samples. Perchlorate sensitive sensing responses were obtained based on measuring the current changes with respect to the assisted transfer reaction of perchlorate ions by a perchlorate selective ligand namely, bis(dibenzoylmethanato)Ni(II) (Ni(DBM)2) across the polarized microhole array interface. Cyclic voltammetry was used to characterize the assisted transfer reaction of perchlorate ions by the $Ni(DBM)_2$ ligand when using the portable sensing device. The current response for the transfer of perchlorate anions by $Ni(DBM)_2$ across the micro-water/gel interface linearly increased as a function of the perchlorate ion concentration. The technique of differential pulse stripping voltammetry was also utilized to improve the sensitivity of the perchlorate anion detection down to 10 ppb. This was acquired by preconcentrating perchlorate anions in the gel layer by means of holding the ion transfer potential at 0 mV (vs. Ag/AgCl) for 30 s followed by stripping the complexed perchlorate ion with the ligand. The effect of various potential interfering anions on the perchlorate sensor was also investigated and showed an excellent selectivity over $Br^-$, $NO_2{^-}$, $NO_3{^-}$, $CO{_3}^{2^-}$, $CH_3COO^-$ and $SO{_4}^{2^-}$ ions. As a final demonstration, some regional water samples from the Sincheon river in Daegu city were analyzed and the data was verified with that of ion chromatography (IC) analysis from one of the Korean-certified water quality evaluation centers.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.4
• /
• pp.310-318
• /
• 2015

In this paper, dual-port eFuse OTP (one-time programmable) memory cells with smaller cell sizes are used, a single VREF (reference voltage) is used in the designed eFuse OTP IP (intellectual property), and a BL (bit-line) sensing circuit using a S/A (sense amplifier) based D F/F is proposed. With this proposed sensing technique, the read current can be reduced to 3.887mA from 6.399mA. In addition, the sensing resistances of a programmed eFuse cell in the program-verify-read and read mode are also reduced to $9k{\Omega}$ and $5k{\Omega}$ due to the analog sensing. The layout size of the designed 32-bit eFuse OTP memory is $187.845{\mu}m{\times}113.180{\mu}m$ ($=0.0213{\mu}m2$), which is confirmed to be a small-area implementation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.838-841
• /
• 2012

To avoid the damage to circuit and performance degradation by temperature changes, temperature sensing circuit applicable to the IC is proposed in this paper. Temperature sensing is executed by PTAT circuit and power saving mode is activated by internal switch if internal temperature is in high. Also, characteristics of current matching are increased by using current mirror and cascode circuits. From the simulation results, this circuit is operating in action mode if input signal is in low. But it immediately goes into power saving mode if output signal is in high. It shows the output voltage of 1V at $75^{\circ}C$ and 1.75V at $125^{\circ}C$ in action mode and near 0 V(0V~ 7uV) in power saving mode.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.4
• /
• pp.9-16
• /
• 2014

A proton exchange membrane is a core component in the proton exchange membrane fuel cell because the role of proton exchange membrane(PEM)is supplying proton conductivity to fuel cell, a gas separator, and insulating between an anode and cathode. Among various role of PEM, supplying proton conductivity is the most important and the proton conductivity is strongly related the structural evolution of PEM by hydration. Thus a lot of studies have done by past few decade based on small angle X-ray scattering and wide angle X-ray scattering for understanding morphological structure of the PEM. Resulting from these studies, several morphological models of hydrated PEM are proposed. Current sensing atomic force microscopy (CSAFM) can map morphology and conductance on the membrane simultaneously. It can be the best tool for studying heterogenous structured materials such as PEM. In this study, the hydration of the membrane is examined by using CSAFM. Conductance and morphological images are simultaneously mapped under different relative humidity. The conductance images, which are mapped from different relative humidity, are analyzed by statistical methode for understanding ionic channel variation in PEM.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.6-7
• /
• 2008

Current sensing in power semiconductors involves sensing of over-current in order to protect the device from harsh conditions. This technique is one of the most important functions in stabilizing power semiconductor device modules. The sense FET is very efficient method with low power consumption, fast sensing speed and accuracy. In this paper we have analyzed the characteristics of proposed sense FET and optimized its electrical characteristics to apply conventional 450V power MOSFET devices by numerical and simulation analysis. The proposed sense FET has the n-drift doping concentration $1.5\times10^{14}cm^{-3}$, size of $600{\mu}m^2$ with 4.5 $\Omega$, and off-state leakage current below 50 ${\mu}A$. We offer the layout of the proposed sense FET to process actually. The offerd design and optimization methods is meaningful, which the methods can be applied to the power devices having various breakdown voltages for protection.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.17 no.2
• /
• pp.214-219
• /
• 2007

In this paper, a new magnetic position sensing mettled for autonomous vehicle and robot guidance is presented. In autonomous vehicle and robot control, position sensing is an important task for the identification of their locations, such as the current position within a trajectory. The magnet based autonomous vehicle and robot was identified position via magnetic materials. In the magnetic sensing system, the Earth field is one of the largest disturbance. To removal of the Earth field, this paper proposes 1-dimensional magnetic field sensors array and develops precise petition sensing system using linear operating region of the magnetic field sensor. This proposal is verified a feasible magnetic position sensing system for autonomous vehicle and robot guidance by the experimental results.

• Journal of the Korean Magnetics Society
• /
• v.26 no.2
• /
• pp.62-66
• /
• 2016

We designed a model composed a ring type magnet, a yoke, and a sensing coil buried in a projectile for calculating the muzzle velocity based on the voltage induced from sensing coil by simulation. The muzzle velocity was calculated from the master curve obtained through the voltage induced from sensing coil by simulation. The induced voltage increased with increasing the diameter of sensing coil. The projectile's velocity was proportional to the induced voltage when the sensing coil was buried in projectile. The projectile will be surely exploded at the target region by inputting the information of muzzle velocity variation corrected the diameter effect of induced voltage of sensing coil.