• ETRI Journal
• /
• v.32 no.2
• /
• pp.327-329
• /
• 2010

A fully integrated small form-factor HBT power amplifier (PA) was developed for UMTS Tx applications. For practical use, the PA was implemented with a well configured bottom dimension, and a CMOS control IC was added to enable/disable the HBT PA. By using helix-on-pad integrated passive device output matching, a chip-stacking technique in the assembly of the CMOS IC, and embedding of the bulky inductive lines in a multilayer substrate, the module size was greatly reduced to 2 mm ${\times}$ 2.2 mm. A stage-bypass technique was used to enhance the efficiency of the PA. The PA showed a low idle current of about 20 mA and a PAE of about15% at an output power of 16 dBm, while showing good linearity over the entire operating power range.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.333-336
• /
• 2000

This paper describes a CMOS low noise amplifier (LNA) with bias current reusing architecture intended lot use in the front-end of IMT-2000 receiver. It has been implemented in a 0.35$\mu\textrm{m}$ CMOS process with two poly and four metal layers. In order to accuracy of simulation, we considered a bonding wire and a pad effect and used the measurements of capacitors and on-chip inductors which implemented in the same process. The LNA has a forward gain (S21) of 17 ㏈ and a noise fjgure of 1.26 ㏈. And it has a third-order intermodulation intercept point (IP3) of +3.15 ㏈m and a 1㏈ compression point (P1㏈) of -16 ㏈m, input referred, respectively. The power consumption is 19 ㎽ from a 3V supply.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.791-794
• /
• 1998

This paper presents a constant gm input stagefor low-voltage rail-to-rail operational amplifier. A proposed scheme uses two current paths to keep sum of the biasing currents of the complimentary input pairs. The op amp was designed in a $0.8\mu\textrm{m},$ n-well CMOS, double-polysilicon and double-metal technology. This achieved in weak inversion. The circuit can operate in power supply voltage from 1.5V up to 3V. An open-loop gain, AV, was simulated as 84dB for 15pF load. An unit-gain frequency, fT was 10MHz.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.213-215
• /
• 2003

The continuing need for more compact and reliable switching power supplies have aroused a renewed interest in a well founded control technique the Magnetic Amplifier(Magamp). Magamp have some advantages of higher power density simple control circuit, good regulation, high frequency and high performance. The control method with magamp become attractive solutions for high current post regulated output applications. In this study, it is proposed that the magamp technique in flyback converters with multiple output windings. Operation principle of the proposed approach is described and a description of magamp control loop behavior is given first from a circuit level point of view. Then the focus is shifted to look at the same issue from the block diagram point of view. Experimental verifications on 50W multiple output flyback converter are conducted. Simulations and experimental results show that the proposed approach is high efficiency and voltage regulation of the auxiliary output is excellent.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.33B no.3
• /
• pp.47-55
• /
• 1996

An optical transmitter, which is a key component of the optical transmission system, converts the electrical signal to optical signal and consists of a high-speed current-pulse driver for laser diode and low-speed feedback loops that stabilize optical power against aging, power supply voltage fluctuations, and ambient temperature changes. In this paper, the power-stabilizing part, which forms the bulk of the optical transmitter circuitry was designed in integrted circuits. Operational amplifiers and reference voltage generation circuits, which were identified as key building blocks for the power-stabilizing feedback loops, were designed and were subsequently verified through HSPICE simulations. The designed operational amplifier consists of a two-stage folded cascode amplifier and class AB output stage, whereas the reference voltage is obtained by bandgap reference circuits. Finally the power-stabilizing circuitry was laid out based on 3\mu$m CMOS design rules for fabrication.

• 한국정보통신설비학회:학술대회논문집
• /
• 2004.08a
• /
• pp.23-26
• /
• 2004

본 논문은 전력증폭기의 효율을 개선하기 위한 도허티증폭기의 특성 분석에 관한 것이다. 도허티증폭기의 특성을 분석하기 위해 2-tone신호와 WCDMA신호를 사용하였고 180W PEP LDMOSFET을 사용하였다. 제작된 도허티증폭기는 출력 전력 20W에서 약 10%정도의 효율개선을 나타냈지만 선형성이 저하되는 특성을 나타내었다. 저하된 선형성을 개선시키기 위해 carrier 증폭기(Amp. A)와 peaking 증폭기(Amp. B)를 각각 변화하였으며, carrier 증폭기는 높은 PEP(Peak Envelope Power)와 적은 Id(drain current)가 되도록 하였고, peaking 증폭기는 높은 이득과, 낮은 gate bias에서 IMD(Intermodulation Distortion)가 상쇄되도록 하였다. 최종 측정 결과 출력전력 20W에서 선형성은 class AB증폭기와 비교하여 유사한 결과를 얻었으며, 효율은 약 10% 이상의 개선을 얻을 수 있었다.

• Journal of IKEEE
• /
• v.11 no.3
• /
• pp.122-128
• /
• 2007

Sinusoidal voltage-controlled oscillators (VCOs) based on Colpitts and Hartley oscillators are presented. They consist of a LC parallel-tuned circuit connected in a negative-feedback loop with an OTA-R amplifier and two diode limiters, where the inductor is simulated one realized with temperature-stable linear operational transconductance amplifiers (OTAs) and a grounded capacitor. Prototype VCOs are built with discrete components. The Colpitts VCO exhibits less than 1% nonlinearity in its current-to-frequency transfer characteristic from 4.2 to 21.7 MHz and ${\pm}$95 ppm/$^{\circ}C$ temperature drift of frequency over 0 to $70^{\circ}C$. The total harmonic distortion (THD) is as low as 2.92% with a peak-to-peak amplitude of 0.7 V for a frequency-tuning range of 10.8-32 MHz. The Hartley VCO has the temperature drift and THD of two times higher than those of the Colpitts VCO.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.1047-1051
• /
• 2004

Charge amplifier systems benefit from the very wide dynamic range of PE accelerometers by offering flexibility in adjusting the electrical output characteristics such as sensitivity and range. They are well suited for operation at high temperatures. Modern charge systems feature improved low noise operation, simplified digital controls, and dual mode operation for operation with charge or IEPE voltage mode sensors. high impedance circuitry is not well suited for operation in adverse field or factory environments. The resolution of a PE accelerometer may not be specified or known since noise is a system consideration determined by cable length and amplifier gain. IEPE accelerometrs operate from a constant current power source, provide a high-voltage, low-impedance, fixed mV/g output. They operate through long, ordinary, coaxial cable in adverse environments without degradation of signal quality. They have limited high temperature range. IEPE sensors are simple to operate. Both resolution and operating range are defined specifications. Cost perchannel is lower compared to PE systems since low-noise cable and charge amplifiers are not required.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1613-1616
• /
• 2008

A Transcutaneous Energy Transmission System (TET) has been developed for the wireless energy transmission with two magnetically coupled coils. A resonance circuit is used to raise the induced voltage and current of the secondary coil. Its resonance frequency depends on the internal resistance of circuit and the transferred energy. Because the transferred energy usually changes in wide range, the output voltage is unstable and the energy transferring efficiency decrease. A push-pull class E amplifier is usedto generate high frequency AC voltage. To maintain proper resonance frequency, the voltage output of the amplifier was continuously monitored and adjusted to the optimized resonance frequency. Because of its high frequency (370 kHz), a phase lockedloop circuit and a comparator are used to monitor the output waveform. The results of experimentaldata show that the PLL circuit can increase the transmission efficiency and stabilize the output voltage of TET.

• 전기의세계
• /
• v.19 no.3
• /
• pp.18-25
• /
• 1970

Chesin-1 telephone currently used in Korea is quite similar in design to early Japanese model of Type-4 telephone which is now being replaced by Type-600 having much improved characteristics. Chesin-1 telephone has a relatively high side-tone level, since the line impedance was taken as a purely resistive component for simplicity in the design of its transmission networks. To meet a current trend of using a smaller diameter of wire for telephone line, it is necessary to improve the present type which has a limited receiving efficiency. A new telephone set has been designed to have an amplifier and a R-C coupled side-tone balancing network. The set offers 8dB gain in the overall performance of transmitting and receiving without any unbearable side-tone disturbances. The paper describes both theoretical and experimental characteristics of the new set.