• 한국응용과학기술학회지
• /
• 제19권4호
• /
• pp.311-319
• /
• 2002

Environmental friendly acrylic/urea high-solid paint(MUHC) were prepared through the curing reaction of acrylics resin(EBHC) containing 70wt% of solids content and butylated urea curing agent. The synthesis of EBHC Was done at $150^{\circ}C$ for 6 hours, and the results were obtained as follows : $M_{n}=1830{\sim}2190$, $M_{w}$ $3290{\sim}4000$, $M_{w}/M_{n}$=1.80{\sim}1.83$ viscosity=$110{\sim}352$ cps, and conversion=$82{\sim}92$%. After the film was coated with MUHC, the various physical properties were measured. They showed that enhancement of the coating properties such as adhesion, flexibility, abrasion resistance, impact resistance, and water resistance could be expected through introdl1cing caprolactone acrylate component in acrylics resin for the high-solids content acrylics/urea coatings.

• 한국축산식품학회지
• /
• 제31권4호
• /
• pp.497-505
• /
• 2011

The objective of this study was to examine the effect of hot-boning and soy sauce as a curing agent on the processing properties of beef jerky. Beef jerky was prepared under the following four treatment conditions; Beef jerky with cold-boned beef and salt solution, beef jerky with cold-boned beef and soy sauce solution, beef jerky with hot-boned beef and salt solution, and beef jerky with hot-boned beef and soy sauce solution. Cured meat and jerky containing hot-boned beef had a significantly higher pH, water holding capacity (WHC), moisture content, Myofibrillar fragmentation index (MFI), processing yields, tenderness, and sensorial scores than samples containing cold-boned beef (p<0.05). Regardless of the raw materials, the jerky containing soy sauce had a significantly lower pH, WHC, moisture content, salt content, TBA, CIE $L^*$ and $b^*-$ values, and significantly higher MFI, mechanical tenderness, and sensorial scores (p<0.05). Based on these findings, we concluded that the use of hot-boned meat and soy sauce was the most effective boning method and curing agent during beef jerky processing.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 추계학술발표대회 논문집
• /
• pp.34-37
• /
• 2000

The effect of novel N-crotyl-N,N-dimethyl-4-methylanilinium hexafluroantimonate (CMH) curing agent on cure behavior and thermal properties of DGEBA epoxy cationic system was investigated. From DSC measurements of DGEBA/CMH system, it was shown that this system exhibits an excellent thermal latent characteristic in a given temperature and reveals complex cure behavior as indicated by multiple exotherms. The conversion and conversion rate of DGEBA/CMH system increased with increasing the concentration of initiator due to high activity of CMH. Viscoelastic properties during gel formation of DGEBA with CMH were investigated by rheological techniques under isothermal condition. The gel time obtained from the modulus crossover. point t(G')=G", was affected by high curing temperature and concentration of CMH, resulting in high degree of network formation in cationic polymerization. The thermal stabilities were discussed in terms of the activation energy for decomposition and thermal factors determined from TGA measurements.ents.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.183-188
• /
• 2002

When Concrete work during winter is placed, it has anxiety that concrete freeze at low temperature. As concrete's freezing cause reduction of durability, it is necessary for mixing to pay attention to Air content and W/C ratios. Accordingly, in this study, we set up three series and evaluate a frost-resistance of concrete with admixture, like fly-ash and blast-furnace slag, for early curing method and types of chemical admixture..The study is composed as; I series : Analysis for early curing method and types of chemical admixture in laboratory II series : Analysis for early curing method and types of chemical admixture in batcher plant and measured concrete' temperature. The result of this study, it was more effective the use of super-plasticizers than air entraining agent.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.647-650
• /
• 2005

This paper is to investigate the shrinkage properties of ultra high strength concrete(UHSC) incorporating $5\%$ of expansive additives(EA) along with $1\%$ of shrinkage reducing agent(SRA). UHSC subjected to steam curing and incorporated with steel fiber exhibited higher compressive strength than control UHSC by as much as50MPa at 7days, while at 28days, noticeable change in compressive strength was not observed between UHSC mixtures. Control UHSC subjected to steam curing had a $922{\times}10^6$ of autogenous shrinkage strain value, which was 6.7 times of drying shrinkage strain value at 42 days. The combination of EA and SRA resulted in a decrease in autogenous shrinkage by as much as half of control mixture. Steam curing contributed to the reduction of autogenous shrinkage by as much as $11\%$ compared with that of standard curing.

• Composites Research
• /
• 제17권4호
• /
• pp.40-46
• /
• 2004

본 연구에서는 single lap 전단시험을 통해 자가치료제와 촉매의 혼합비율 및 경화온도가 자가치료용 폴리머 복합재에 적용되는 자가치료제의 접착성능에 미치는 영향을 조사하였다. 자가치료세로는 DCPD (dicyclopentadiene), ENB(5-ethylidene-2-norbornene), DCPD와 ENB가 혼합된 경우를 고려하였으며 촉매로는 bis(riclohexylphosphine) benzyllidine rethenium (IV) dichloride Grubbs' catalyst를 사용하였다. 이때 DCPD에 대한 촉매의 혼합비율은 1.0wt%와 0.5wt%, ENB에 대한 촉매의 혼합비율은 0.lwt%, DCPD와 ENB의 혼합액에 대한 촉매의 혼합비율은 0.5wt%를 적용하였으며 경화온도는 $25^{\circ}C$, $60{\circ}C$, $80^{\circ}C$를 고려하였다. 연구결과에 따르면 DCPD의 경우 안정화된 접착강도를 얻기 위해서는 많은 양의 촉매와 긴 경화시간이 요구되었다 ENB의 경우는 DCPD의 경우에 비해 촉매의 혼합비율이 낮아도 빠른 경화반응을 얻을 수 있었지만 경화시간이 증가함에 따라 접착전단강도는 DCPD와는 달리 최대 값에 도달하였다가 점차 감소하면서 안정화되는 양상을 나타내었다. DCPD와 ENB의 혼합액 경우도 ENB와 유사한 경화거동을 나타내며 DCPD에 대한 ENB의 혼합비율이 높을 수록 경화반응이 빨라지는 양상을 얻을 수 있었다. 아울러 경화온도가 높을수록 집착전단강도는 증가되며 안정화된 평탄부에 도달하는 경화시간은 짧아짐을 알 수 있었다

• ETRI Journal
• /
• 제38권6호
• /
• pp.1179-1189
• /
• 2016

A chemorheological analysis of a no-flow underfill was conducted using curing kinetics through isothermal and dynamic differential scanning calorimetry, viscosity measurement, and solder (Sn/27In/54Bi, melting temperature of $86^{\circ}C$) wetting observations. The analysis used an epoxy system with an anhydride curing agent and carboxyl fluxing capability to remove oxide on the surface of a metal filler. A curing kinetic of the no-flow underfill with a processing temperature of $130^{\circ}C$ was successfully completed using phenomenological models such as autocatalytic and nth-order models. Temperature-dependent kinetic parameters were identified within a temperature range of $125^{\circ}C$ to $135^{\circ}C$. The phenomenon of solder wetting was visually observed using an optical microscope, and the conversion and viscosity at the moment of solder wetting were quantitatively investigated. It is expected that the curing kinetics and rheological property of a no-flow underfill can be adopted in arbitrary processing applications.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권6호
• /
• pp.527-533
• /
• 1994

In this study, it was studied on dielectric breakdown strength and thennostability properties due to the structure variation of matrix resin and treatment of coupling agent of epoxy insulating materials. The interpenetrating network structure was formed by simultaneous heating curing the epoxy resin with single network structure and the methacrylic acid resin. Also inner structure was observed and the glass transition temperature was measured on these three type specimens. Dielectric breakdown properties were investigated by applying DC, AC and impulse voltage. As a result, the glass transition temperature and the dielectric breakdown strength of specimen with interpenetrating network structure was more higher than another two type specimens.

• 한국세라믹학회지
• /
• 제27권3호
• /
• pp.437-443
• /
• 1990

The resistivity of cement paste and mortar for freezing and thawing was investigated for densifying the structure of cement paste and mortor, slag, diatomaceous earth and fly ash as blending materials and superplasticizer were used, and air entraining agent was added to absorb the volume expansion by freezing and thawing reaction. And then the specimens were subjected to freeze-thaw in water. When both of air entraining agent and superplasticizer as additives were mixed to specimens, their freeze-thaw resistance was enhanced by the air entraining effect and the water reduction effect. When 4% of slag were added to cement, freeze-thaw resistance was especially excellent. In addition, it was found that the specimens with blending materials were more influenced by curing periods than those without admixture. It is assumed that the curing periods contribute to exibit the potential hydraulicity and pozzolanic reactivity of blending materials and to densify their texture.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.96-99
• /
• 2004

Silica fillers were coated by plasma polymer coatings of 1,3-diaminopropane, allylamine, pyrrole, 1,2-epoxy-5-hexene, allyl mercaptan and allyl alcohol using RF plasma (13.56 MHz). The coated fillers were then mixed with biphenyl epoxy, phenol novolac (curing agent) and/or triphenylphosphine (catalyst), and subjected to DSC analyses in order to elucidate the chemical reaction between functional moieties in the plasma polymer coatings and the epoxy resin. Only the samples with 1,3-diaminopropane and allylamine plasma polymer coated silica fillers showed heat of reaction peaks when they were mixed with biphenyl epoxy resin only, while these samples as well as the samples with 1,3-diaminopropane, allylamine and pyrrole plasma polymer coated silica fillers exhibited heat of reaction peaks when mixed with both biphenyl epoxy and phenol novolac (curing agent).