• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.391-394
• /
• 2003

Laser direct writing process is developed 3rd harmonic Diode Pumped Solid State Laser with the near visible wavelength of 355 m sensitive polymer is irradiated by UV laser and developed using polymer solvent to obtain quasi-3D. It is important to reduce line width for image mode waveguides, so some investigations will be carried out in various conditions of process parameters such as laser power, writing speed, laser focus and optical properties of polymer. This process could be to fabricate a single mode waveguide without expensive mask projection method. Experimentally, the patterns of trapezoidal shape were manufactured into dimension of 8.4 mm width and 7.5 mm height. Propagation loss of straight waveguide measured 3 dB/cm at 1,550 nm.

• Composites Research
• /
• v.14 no.1
• /
• pp.22-29
• /
• 2001

The purpose of this paper is to determine the effect of the autoclave inner pressure rate, heat-up rate, tool round angle, Thickness of core, height of joggle on defects, and to minimize the defects of aircraft sandwich structure reinforced with honeycomb core occurred in autoclave processing. The results showed that the geometry of aircraft sandwich structure and tool such as tool round angle, thickness of core, height of joggle, and the autoclave cure conditions such as inner pressure rate, heat up rate strongly affected the core movement, core wrinkle, bridge phenomenon of prepreg and depression of core that occurred in autoclave processing.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.196-201
• /
• 2004

Adhesive joints have been widely used for fastening thin adherends because they can distribute the load over a larger area than mechanical joints, require no hole, add very little weight to the structure and have superior fatigue resistance. However, the fatigue characteristics of adhesive joints are much affected by applied pressure during curing operation because actual curing temperature is changed by applied pressure and the adhesion characteristics of adhesives are very sensitive to manufacturing conditions. In this study, cure monitoring and torsional fatigue tests of adhesive joints with an epoxy adhesive were performed in order to investigate the effects of the applied pressure during curing operation. From the experiments, it was found that the actual curing temperature increased as the applied pressure increased, which increased residual thermal stress in the adhesive layer. Therefore, the fatigue life decreased as the applied pressure increased because the mean stress during fatigue tests increased due to the residual thermal stress.

• Textile Coloration and Finishing
• /
• v.5 no.1
• /
• pp.1-9
• /
• 1993

The polymethylhydrosiloxane(PMHS) was synthesized by the co-hydrolysis of methyldichlorophydrosilane and ethyl ether, also polydimethylsiloxane(PDMS) was synthesized by the hydrolysis of dimethyl dichlorosilane and ethyl ether. The silk fabrics were treated with PMHS and PDMS in order to improve the water repellency and the wrinkle recovery. Also the effect of PMHS concentration, PDMS concentration and cure temperature on the physical properties of silk fabrics were studied. The maximum water repellency and maximum wrinkle recovery were obtained from the fabrics treated under the conditions 5%-PMHS and PDMS at 16$0^{\circ}C$, and 3%-PMHD and PDMS at 16$0^{\circ}C$, respectively. The tensile strength, the breaking elongation, the reflection and the bending properties of silk fabrics were not degraded severely by the treatment of PMHS or PDMS.

• Fashion & Textile Research Journal
• /
• v.2 no.2
• /
• pp.123-131
• /
• 2000

Diphenyl-2-ethanolamidophosphate (DPEOAP) was synthesized to treat polyester fabrics in order to improve its flame retardancy. The flame retardancy and physical properties of DPEOAP-treated polyester fabrics were investigated. The results were as follows: 1) polyester fabrics can be treated with DPEOAP by means of Pad-Dry-Cure method, because DPEOAP was easily soluble in benzene. 2) The most economic conditions of treatment were determined as 10% of DPEOAP cocentration, $140^{\circ}C$ of curing temperature, and 2 minutes of curing time. 3) Though the washablity of DPEOAP is low in comparison with the other products which are purchasable in a market, it has an excellent flame retardment effect 3 times more than in number of flame contact just with 0.66% add-on. 4) The physical properties of DPEOAP treated polyester fabrics were little changed as compared with non-treated fabric.

• The Journal of Korean Medicine
• /
• v.21 no.4
• /
• pp.3-8
• /
• 2000

Xiexiafa is the one of eight methodes of treatment, the purgatives of oriental medicine was originated from Shanghanlun written by Zhangzhongjing. Traditionally Xiexiafa has been used to treat constipation. But All kinds of researches on Xiexiafa made purgatives possible to use variously for the disease of internal medicine. In the research on clinical use of Xiexiafa, the results were as follow. Xiexiafa is available on emergency medicine because of instant relief. It has an ability of preventive medicine and economical effect. It was considered to treat hard to cure and chronic diseases made by Sushi, Rexie, Shuijie, Tanzhi, Xuxie etc. Considering strong side effects of Xiexiafa and patient conditions, it must be used carefully.

• Journal of Applied Reliability
• /
• v.16 no.3
• /
• pp.216-223
• /
• 2016

Purpose: This paper suggests the procedure to enhance the reliability of the software of the medical device that is to cure, treat, diagnose, and prevent a disease or an abnormal health conditions. Methods: After test requirements are classified by the software requirements specification for safety and backgrounds, reliability assessment methods are suggested. Results: Verification and validation for function and safety can be performed whether the medical device software are implemented as intended. Conclusion: Procedure on the static analysis, unit test, integration test, and system test are provided for the medical device software.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1847-1850
• /
• 2008

The process conditions during ultraviolet nanoimprint lithography (UV-NIL) process such as temperature, stamping pressure, UV irradiation, etc. are effective factors for successful imprinting of complex and fine patterns. In this study, the effects of aluminum mold on the thermal characteristics of UV-NIL process were investigated through imprinting experiments and numerical simulations. The temperature of polymer resin on mold was measured to study thermal characteristics during UV curing. From the experimental and numerical results, the importance of curing reaction control for UV-NIL process was discussed for deformation characteristics.

• Textile Coloration and Finishing
• /
• v.9 no.4
• /
• pp.1-6
• /
• 1997

Water repellent finish was carried out using water repellent agent(AG-480), melamine resin(Sumitex Resin MK), and catalyst(Sumitex Accelerator ACX). PET/nylon fabrics were treated with melamine resin by pad-dry-cure method and subsequently washed and dried. Durable water repellency was controlled by the melamine resin and catalyst. Water repellency was tested by spray rating method and durability of water repellency were measured by launder-O-meter and pilling tester. The optimum conditions of durable water repellent finish for new synthetic fabric were as follows; concentration of water repellent finishing agent 20g/l; concentration of melamine & catalyst 0.5g/l; curing condition $160^{\circ}$ ${\times}$ 30sec. Water repellency after washing and rubbing is improved by melamine resin and catalyst.

• Elastomers and Composites
• /
• v.4 no.1
• /
• pp.83-88
• /
• 1969

As a part of a series of previous studies, physical properties of various portions of a tire made of NR-Syn. R bloods were studied. 1. It was found, in general, most effective for tire tread when 50 parts of HAF black was blended with NR and Syn. R with a ratio of 70/30. 2. It was found that the use of SBR 1712 has an advantage in price, easy processing and physical properties than other synthetic rubber. 3. A technical compounding of various portions of a tire has to be determined for optimum cure conditions.