• 한국CDE학회지
• /
• 제21권2호
• /
• pp.50-60
• /
• 2015

Corresponding to the high consumption rate of the selfie stick for cell phone camera, the design of the product is becoming diverse. However, relatively low cost selfie stick models are not strong enough to stand the weight of the cell phone. This results into a bending of the stick or the accidental fall of the cell phone by the failure of the holding unit. As a solution to the problem, design of selfie stick that is structurally strong enough to stand the weight of the cell phone with the minimum weight for the portability is proposed in this paper.

• Environmental Engineering Research
• /
• 제23권2호
• /
• pp.210-215
• /
• 2018

Coal seam gas (CSG) water, to be discharged, has been usually treated in reverse osmosis (RO) plants which require extensive and expensive pre-treatment. However, current low gas prices have been a great driver for relevant industries to seek for alternative cost-effective technologies in the aspect of its beneficial use and fit-for-purpose usable water production. In this paper, a combined system with a two-stage pore control fiber (PCF) filtration and a RO system was designed and tested for CSG water treatment. Also, a coagulation reactor was placed in front of the PCF to further enhance suspended solid removal. More than 99% of SS were removed through the PCF filtration while organic, total nitrogen and total phosphorous were mostly removed by the RO system. Especially along with a decrease in conductivity, the total dissolved solid derived from salts was mainly removed in the RO system. Having $OH^-$ undetected, $HCO_3{^-}$ was found to be a dominant compound and its removal efficiency was 97-98% after the RO treatment. And a Fe(III) type of Polytetsu, which was the first to be tested in this paper, was found to be a better option than a Al(III) type of Poly Aluminium Chloride due to its greater coagulation efficiency and applicability at a broader range of pH than the Al(III) type. In addition, there was no noticeable change in oxidation reduction potential, suggesting that an additional process is required to oxidize non-ionic organic carbons (detected as total organic carbon).

• Asian Pacific Journal of Cancer Prevention
• /
• 제13권5호
• /
• pp.2363-2367
• /
• 2012

Objective: To investigate the association between the connexin 37 C1019T polymorphism and Helicobacter pylori infection in patients with gastric cancer. Methods: 388 patients with gastric cancer (GC), 204 with chronic superficial gastritis (CSG) were studied. H. pylori was detected by gastric mucosal biopsies biopsy dyeing method. Connexin 37 gene polymorphism 1019 site genotypes were determined by gene sequencing technology. Genotypes and alleles frequencies were compared. Results: (1) Connexin37 gene 1019 site distribution frequency (CC type, TC type, TT type) in the CSG group was 18.1%, 45.1% and 36.8%; in the stomach cancer group it was 35.1%, 45.9% and 19.%, conforming to the Hardy-Weinberg euilibrium. (2) In comparison with CSG group, the frequency of Connexin37 C allele was higher in the gastric cancer group (58.0% vs 40.7%, OR = 2.01, 95%CI = 1.58-2.57, P < 0.01). The prevalence of gastric cancer risk was significantly increased in the carriers of C allele (CC+TC) than in TT homozygote (OR = 2.47, 5%CI = 1.68- 3.610. (3) Gastric cancer patients complicated with Hp infection 211 cases, gastric cancer group of the male patients with HP positive patients with 187 cases, 40 cases of female patients with negative patients, 24 cases were HP positive, negative in 137 cases, control group male patients, 28 cases were Hp positive, negative in 95 patients, female patients with Hp positive 6 cases, 75 cases were negative. On hierarchical analysis, the male group OR value was 15.9 (95%CI to 9.22-27.3), and the female OR was 2.19 (95%CI 0.88-5.59), indicating a greater contribution in males (P <0.01). After elimination of gender effects, positive HP and gastric cancer were closely related (OR 8.82, 95% CI: 5.45-14.3). (4) The distribution frequency of C allele in patients with Hp infection was much higher than that in Hp negative cases in the GC group (64.5% vs 47.0%, OR = 2.05, 95%CI = 1.54-2.74, P < 0.01). Compared with TT homozygotes, (CC+TC) genotype prevalence of gastric cancer risk increased significantly (OR = 2.96, 5%CI = 1.76-2.99 ). Conclusion: The T allele in the connexin37 gene might not only be associated with gastric cancer but also with H. pylori infection.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.483-495
• /
• 2020

Dams are vital infrastructures that are expected to maintain their stability during seismic excitations. Accordingly, cemented material dams are an emerging type, which are being increasingly used around the world owing to benefiting from advantages of both earth-fill and concrete gravity dams, which should be designed safely when subjected to strong ground motion. In the present paper, the seismic performance of a cemented sand and gravel (CSG) dam is assessed using incremental dynamic analysis (IDA) method by accounting for two failure modes of tension cracking and base joint sliding considering the dam-reservoir-foundation interactions. To take the seismic uncertainties into account, the dam is analyzed under a suite of ground motion records and then, the effect of friction angle for base sliding as well as deformability of the foundation are investigated on the response of dam. To carry out the analyses, the Cindere dam in Turkey is selected as a case study, and various limit states corresponding to seismic performance levels of the dam are determined aiming to estimate the seismic fragilities. Based on the results, sliding of the Cindere dam could be serious under the maximum credible earthquake (MCE). Besides, dam faces are mostly to be cracked under such level of intensity. Moreover, the results indicate that as friction angle increases, probability of sliding between dam and foundation is reduced whereas, increases tensile cracking. Lastly, it is observed that foundation stiffening increases the probability of dam sliding but, reduces the tensile damage in the dam body.

• KSBB Journal
• /
• 제24권1호
• /
• pp.25-29
• /
• 2009

Saccharomyces cerevisiae의 deletion mutant를 이용하여 ydc1, ypc1, scs7, sur1, csg2, ipt1, Icb4, Icb5, dpll의 deletion이 세라마이드의 생산에 미치는 영향을 고찰하였다. 세라마이드는 ELSD가 연결된 HPLC를 통하여 분석하였으며 ${\triangle}$ydc1 mutant의 세라마이드 생산량이 6 mg ceramide/g cell로 최대량을 나타내었으며 ${\triangle}$sur1 mutant, ${\triangle}$lcb5 mutant, ${\triangle}$dpll mutant의 경우 control로 사용한 BY4742와 비슷한 세라마이드 생산량을 나타내었고, 그 외 ${\triangle}$ypc1 mutant, ${\triangle}$scs7 mutant, ${\triangle}$csg2 mutant, ${\triangle}$ipt1 mutant, ${\triangle}$lcb4 mutant는 BY4742보다 낮은 세라마이드 생산량을 나타내었다.

• 문화기술의 융합
• /
• 제3권3호
• /
• pp.37-42
• /
• 2017

본 연구는 피부의 각질층에 분포되어 있는 유지질의 변화 상태를 조절하는 구조체계에 대해 고안한다. 피부구조에 유지질 성분이 어떻게 진행되는지 형태학으로 구성하였고, 주어진 세포사이와 세포횡단의 조건으로 기계적으로 조절되는 형태를 구성하였으며, 구조적인 기능으로 조절기능의 변화 상태를 확인하였다. 유지질 성분에서 피부의 모형을 구성하여 각층에 따른 유기질 상태의 피부 임피던스를 피부의 측정 임피던스 시스템으로 구성하여 진행하였다. 측정 임피던스는 ${\lambda}-Lip-RSC$, ${\lambda}-Lip-RSL$, ${\lambda}-Lip-CSG$, ${\lambda}-Lip-CSS$ 와 ${\lambda}-Lip-RSB$로 형성하였고, 세포사이와 세포횡단의 조건으로 변화의 차가 있고, 변환을 제어하는 전달시스템을 구성과 변환모델을 세분화하여 구축하였다. 앞으로 유지질 상태에서 피부의 기능적 효능조절이 가능한 유지질 성분의 조절시스템을 구성하여 지속적인 피부의 개선효과가 진행 될 것으로 예상된다.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2006년도 추계공동학술대회
• /
• pp.239-254
• /
• 2006

In mold structure machining, tool interference is a phenomenon which results from a collision between a blade of tool and a workpiece. Also tool collision is a phenomenon which results from a collision of holder with the object to be machined. These phenomena not only cause damages to mold and tool but also increase machining time and cost. To detect a collision of a tool to mold structure, first of all, the mold structure and a tool must be defined with famous geometric models such CSG, B-rep, and Voxel. A tool is defined as a combination of the blade, the shank, and the holder. This thesis reviews various collision detection algorithms using z-map and computer 3D graphic collision detection algorithms for the tool in machining a mold structure.

• 전자공학회논문지A
• /
• 제28A권10호
• /
• pp.847-854
• /
• 1991

This paper presents a new output phase assignment algorithm which determines the phases of all the nodes in a given boolean network. An estimation function is defined, which is represented by the relation between the literals in the given function expression. A weight function, WT (fi, fj) is defined, which is represented by approximate amount of common subexpression between function fi and fj. Common Subexpression Graph(CSG) is generated for phase selection by the weight function between all given functions. We propose a heuristic algorithm finding subgraph of which sum of weights has maximum by assigning phases into the given functions. The experiments with MCNC benchmarks show the efficiency of the proposed method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1093-1097
• /
• 2004

We propose 'the haptic primitive' for haptic rendering without the need to solve complicated parametric equations. To develop 'the haptic primitive', we adopted "the God-Object Method" as a haptic rendering algorithm and applied 'Constructive Solid Geometry' to manage haptic objects. Besides being used in the 'ghost library' of $PHANToMTM^{TM}$ our method can be used as a basic component for developing tools and libraries that aim to simplify haptic modeling. It can also be applied to tactile display modules and temporal display modules. Ultimately it can be developed into a one-stop haptic modeling tool that enables the user to more conveniently create a tangible CAD systems or a tangible e-ommerce system.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 2002년도 춘계공동학술대회
• /
• pp.266-271
• /
• 2002

We propose a hardware accelerated voxelization method for various 3D object model such as surface models, solid models, and volumetric CSG models. The algorithm utilizes the stencil buffer that is one of modern Open히 graphics hardware features. The stencil buffer is originally used to restrict drawing to certain portions of the screen. The volumetric representations of given 3D objects are constructed slice-by-slice. For each slice, the algorithm restricts the drawing areas constructed inner region of 3D objects using the stencil buffer, and generates slices of the volumetric representation for target objects. As a result, we can provide volume graphics support for various engineering applications such as multi-axis machining simulation, collision detection and finite element analysis.