• 한국환경생태학회:학술대회논문집
• /
• 한국환경생태학회 2011년 학술대회 논문집 2호
• /
• pp.127-130
• /
• 2010

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2002년도 제24회 KOSCO SYMPOSIUM 논문집
• /
• pp.33-38
• /
• 2002

An optical single cylinder diesel engine equipped with a common-rail injection system has been built to investigate diesel combustion and emission characteristics. Three optical widows (piston crown quartz for bottom view of the cylinder, upper piston quartz for allowing laser sheet and liner quartz for side view) have been placed in the optical engine to visualize spray characteristics and combustion process inside the cylinder. Before doing further research using various optical diagnostics with the optical engine, fundamental combustion experiments and flame visualization incorporating a high speed motion analyser have been carried out with a wide range of engine operating conditions.

• 동력기계공학회지
• /
• 제7권4호
• /
• pp.12-18
• /
• 2003

Various measures have been tried to reduce the NOx emission from diesel engine, but with partial success because the mechanisms of NOx and PM formations appear to have trade-off relation between each other. Therefore it has been known to be difficult to reduce NOx emission and PM emission simultaneously. Two stage combustion method i,e. a combustion process which has rich combustion stage and lean combustion stage one by one, has been developed successfully to reduce NOx formation in the continuous combustion chambers such as in the boilers. But until yet it is not successful to apply the same method in intermittent combustion chamber like in the diesel engine cylinder, as it was, only several research works were carried out. In this study, devised was a uniquely shaped combustion chamber with reformed piston crown intended to keep fuel-rich condition during early stage of combustion and fuel-lean condition during next stage. It was found that the NOx emission decreased significantly at various conditions of operation with the two stage combustion type engines of PR20 type, but other values such as smoke, CO and specific fuel consumption deteriorated as usual.

• International Journal of Ocean System Engineering
• /
• 제2권4호
• /
• pp.209-213
• /
• 2012

Recently, the fuel using in the diesel engines of marine ships has been changed to a low quality of heavy oil because of the steady increase in the price of oil. Therefore, the wear and corrosion in all parts of the engine such as the cylinder liner, piston crown, and spindle and seat ring of exhaust valves has correspondingly increased. The repair welding of a piston crown is a unique method for prolonging its lifetime from an economic point of view. In this case, filler metals with a high corrosion and wear resistance are mainly being used for repair welding. However, often at a job site on a ship, a piston crown is actually welded with mild filler metals. Therefore, in this study, mild filler metals such as CSF350H, E8000B2, and 435 were welded to SS401 steel as the base metal, and the corrosion properties of the weld metals with and without post weld heat treatment were investigated using some electrochemical methods in a 0.1% $H_2SO_4$ solution. The weld metal welded with CSF350H filler metal exhibited the best corrosion resistance among these filler metals, irrespective of the heat treatment. However, the weld metal zones of the E8000B2 and 435 filler metals exhibited better and worse corrosion resistance with the heat treatment, respectively. As a result, it is suggested that in the case of repair welding with CSF350H and 435 filler metals, no heat treatment is advisable, while heat treatment is desirable if E8000B2filler metal is used with repair welding.

• Journal of Ecology and Environment
• /
• 제33권4호
• /
• pp.343-349
• /
• 2010

In Korea, man-caused forest fires are known originate primarily in coniferous forests. We have hypothesized that the vulnerability of Pinus densiflora forests is principally a consequence of the ignition characteristics of the species. To assess this hypothesis, we conducted two combustion experiments using fallen leaves with a reference species, Quercus variabilis. In the first experiments, in which a cigarette was employed as a primary heat source for the initiation of a forest fire, the Pinus leaves caught fire significantly faster (1'1" at Pinus, 1'31" at Quercus, P < 0.001), and ignition proceeded normally. Quercus leaves, on the other hand, caught fire but did not ignite successfully. In the second set of experiments utilizing different moisture contents and fuel loads, the maximum flame temperature of the Pinus leaves was significantly higher ($421^{\circ}C$ at Pinus, $361^{\circ}C$ at Quercus, P < 0.001) and the combustion persisted for longer than in the Quercus leaves (8'8" at Pinus, 3'38" at Quercus, P < 0.001). The moisture contents of the leaves appeared to be a more important factor in the maximum temperature achieved, whereas the most important factor in burning time was the amount of fuel. Overall, these results support the assumption that Pinus leaves can be ignited even by low-heat sources such as cigarettes. Additionally, once ignited, Pinus leaves burn at a relatively high flame temperature and burn for a prolonged period, thus raising the possibility of frequent fire occurrences and spread into crown fires in forests of P. densiflora.

• 한국환경생태학회지
• /
• 제20권2호
• /
• pp.267-273
• /
• 2006

2005년에 발생한 강원도 양양산불피해지의 소나무림을 대상으로 산불피해도를 $\ulcorner$심$\lrcorner$, $\ulcorner$중$\lrcorner$, $\ulcorner$경$\lrcorner$ 단계로 구분하여 산불연소량을 분석하였다. 산불 후 바이오매스는 지표층, 관목층, 수관층으로 나누어 조사하였으며, 산불이 발생하기 전의 바이오매스는 산불 인근 지역의 동일한 재적을 갖는 미피해지 임분과 동일하다고 가정하였다. 지표층과 관목층의 바이오매스는 직접 측정에 의해, 수관층의 바이오매스는 흉고직경과 수고를 이용한 건중량 추정식과 엽면적지수를 이용하여 추정하였다. 피해도가 $\ulcorner$심$\lrorner$으로 분류된 plot에서는 약 l7,451kg/ha이, 피해도 $\ulcorner$중$\lrorner$ plot에서는 8,724kg/ha, 마지막으로 피해가 경미했던 plot에서는 3,693kg/ha이 산불로 인해 연소된 것으로 분석되었다.

• Structural Engineering and Mechanics
• /
• 제87권3호
• /
• pp.221-229
• /
• 2023

Urbanization and industrialization have significantly increased the amount of solid waste produced in recent decades, posing considerable disposal problems and environmental burdens. The practice of waste utilization in concrete has gained popularity among construction practitioners and researchers for the efficient use of resources and the transition to the circular economy in construction. This study employed Lytag aggregate, an environmentally friendly pulverized fuel ash-based lightweight aggregate, as a substitute for natural coarse aggregate. At the same time, fly ash, an industrial by-product, was used as a partial substitute for cement. Concrete mix M20 was experimented with using fly ash and Lytag lightweight aggregate. The percentages of fly ash that make up the replacements were 5%, 10%, 15%, 20%, and 25%. The Compressive Strength (CS), Split Tensile Strength (STS), and deflection were discovered at these percentages after 56 days of testing. The concrete cube, cylinder, and beam specimens were examined in the explorations, as mentioned earlier. The results indicate that a 10% substitution of cement with fly ash and a replacement of coarse aggregate with Lytag lightweight aggregate produced concrete that performed well in terms of mechanical properties and deflection. The cementitious composites have varying characteristics as the environment changes. Therefore, understanding their mechanical properties are crucial for safety reasons. CS, STS, and deflection are the essential property of concrete. Machine learning (ML) approaches have been necessary to predict the CS of concrete. The Artificial Fish Swarm Optimization (AFSO), Particle Swarm Optimization (PSO), and Harmony Search (HS) algorithms were investigated for the prediction of outcomes. This work deftly explains the tremendous AFSO technique, which achieves the precise ideal values of the weights in the model to crown the mathematical modeling technique. This has been proved by the minimum, maximum, and sample median, and the first and third quartiles were used as the basis for a boxplot through the standardized method of showing the dataset. It graphically displays the quantitative value distribution of a field. The correlation matrix and confidence interval were represented graphically using the corrupt method.