• Corrosion Science and Technology
• /
• v.2 no.6
• /
• pp.289-295
• /
• 2003

The corrosion behavior of Cr-N coated steels with different phases (${\alpha}-Cr$, CrN and $Cr_2N$) deposited by cathodic arc deposition on Hl3 steel was investigated in 3.5% NaCl solution at ambient temperature. Potentiodynamic polarization test, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) were the techniques applied to characterize the corrosion behavior. It was found that the CrN coating had a lower current density from potentiodynamic polarization test than others. The porosity, corresponding to the ratio of the polarization resistance of the uncoated and the coated substrate, was higher in the $Cr_2N$ coating than in the other Cr-N coated steels. EIS measurements showed, for the most of Cr-N coated steels, that the Bode plot presented two time constants. Also, the $Cr_2N$ coating represents the characteristic of Warburg behavior after 72hr of immersion. The coating morphologies were examined in planar view and cross-section by SEM analyses and the results were compared with those of the electrochemical measurement. The CrN coating had a dense, columnar grain-sized microstructure with minor intergranular porosity. From the above results, the CrN coating provided a better corrosion protection than the other Cr-N coated steels.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.19-24
• /
• 2010

The current study examined Ag migration from the Ag paste bump in the SABiT technology-applied PCB. A series of experiments were performed to measure the existence/non-existence of Ag in the insulating prepreg region. The average grain size of Ag paste was 30 nm according to X-ray diffraction (XRD) measurement. Conventional XRD showed limitations in finding a small amount of Ag in the prepreg region. The surface morphology and cross section view in the Cu line-Ag paste bump-Cu line structure were observed using a field emission scanning electron microscope (FE-SEM). The amount of Ag as a function of distance from the edge of Ag paste bump was obtained by FE-SEM with energy dispersive spectroscopy (EDS). We used an electron probe micro analyzer (EPMA) to improve the detecting resolution of Ag content and achieved the Ag distribution function as a function of the distance from the edge of the Ag paste bump. The same method with EPMA was applied for Cu filled via instead of Ag paste bump. We compared the distribution function of Ag and Cu, obtained from EPMA, and concluded that there was no considerable Ag migration effect for the SABiT technology-applied printed circuit board (PCB).

• Journal of Information Processing Systems
• /
• v.10 no.1
• /
• pp.1-22
• /
• 2014

Recent technological advances provide the opportunity to use large amounts of multimedia data from a multitude of sensors with different modalities (e.g., video, text) for the detection and characterization of criminal activity. Their integration can compensate for sensor and modality deficiencies by using data from other available sensors and modalities. However, building such an integrated system at the scale of neighborhood and cities is challenging due to the large amount of data to be considered and the need to ensure a short response time to potential criminal activity. In this paper, we present a system that enables multi-modal data collection at scale and automates the detection of events of interest for the surveillance and reconnaissance of criminal activity. The proposed system showcases novel analytical tools that fuse multimedia data streams to automatically detect and identify specific criminal events and activities. More specifically, the system detects and analyzes series of incidents (an incident is an occurrence or artifact relevant to a criminal activity extracted from a single media stream) in the spatiotemporal domain to extract events (actual instances of criminal events) while cross-referencing multimodal media streams and incidents in time and space to provide a comprehensive view to a human operator while avoiding information overload. We present several case studies that demonstrate how the proposed system can provide law enforcement personnel with forensic and real time tools to identify and track potential criminal activity.

• Fire Science and Engineering
• /
• v.29 no.1
• /
• pp.73-79
• /
• 2015

There are three kinds of design method of the fire sprinkler systems. Grid type is connected all branch as a trapezoid. Loop type is connected cross-mains like circle. The last one is a tree type most commonly used. Grid type needs computer program to calculate the friction loss and flow rate apart from very simple form. In loop type, manual calculation is possible. Design engineer can draw up and calculate the demands without computer program. Because water supplies two direction in loop type, friction loss is smaller than tree type. Water distribution in operation area is uniform because of the small differences of sprinklers discharge pressure. Loop type is superior to tree type in respect of total pressure and flow rate. Using the small diameter pipe, the labor and construction cost will be decreased in the end. Loop type sprinkler design is rarely laid out because design engineers don't know the method. This paper is intended to inform that the loop type is better than the tree type in performance and economic point of view. And also this paper intend to use the loop type easily and widely.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.9
• /
• pp.72-80
• /
• 2019

In this task, the tool dynamometer design and manufacture, and the Ansys S/W structural analysis program for tool attachment that satisfies the cutting force measurement requirements of the tool dynamometer system are used to determine the cutting force generated by metal cutting using 3-axis static structural analysis and the LabVIEW system. The cutting power in a cutting process using a milling tool for processing metals provides useful information for understanding the processing, optimization, tool status monitoring, and tool design. Thus, various methods of measuring cutting power have been proposed. The device consists of a strain-gauge-based sensor fitted to a new design force sensing element, which is then placed in a force reduction. The force-sensing element is designed as a symmetrical cross beam with four arms of a rectangular parallel line. Furthermore, data duplication is eliminated by the appropriate setting the strain gauge attachment position and the construction of a suitable Wheatstone full-bridge circuit. This device is intended for use with rotating spindles such as milling tools. Verification and machining tests were performed to determine the static and dynamic characteristics of the tool dynamometer. The verification tests were performed by analyzing the difference between strain data measured by weight and that derived by theoretical calculations. Processing test was performed by attaching a tool dynamometer to the MCT to analyze data generated by the measuring equipment during machining. To maintain high productivity and precision, the system monitors and suppresses process disturbances such as chatter vibration, imbalances, overload, collision, forced vibration due to tool failure, and excessive tool wear; additionally, a tool dynamometer with a high signal-to-noise ratio is provided.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.5
• /
• pp.343-349
• /
• 2021

In The process from design to construction in the existing construction work was less efficient due to the contradictory approach of identifying the 3D state in the plan view and the repeated generation of surveys, floor plans, drawings. Accurate 3D design data is essential for smart construction. However, most of the existing related studies have focused on explaining the development method and main functions of equipment or improving the productivity of smart construction. Therefore, in this study, the utility of 3D design model generation for smart construction and construction survey using 3D laser scanner was evaluated. Plane and vertical road alignment were created using the specifications of the road. The generated road alignment was created as a three-dimensional corridor design using cross-sections at intervals of 20m. In addition, it was possible to create a DTM (Digital Terrain Model) using a digital map and effectively create a 3D design model for the study area through overlapping. Construction survey using a 3D laser scanner showed accuracy within 10cm as a result of the accuracy evaluation. These results proved that construction surveying using a 3D laser scanner is possible because it satisfies the acceptable accuracy of the relevant regulations modeling of target areas using 3D design and construction survey using 3D laser scanner can be a way to address shortcomings of existing GNSS (Global Navigation Satellite System) methods. And accurate 3D data will be used as essential data as basic data for smart construction.

• Advances in nano research
• /
• v.7 no.2
• /
• pp.125-134
• /
• 2019

The Origanum vulgare L.-mediated synthesis of Ag nanoparticles was successfully realized within the present study. Various concentrations of the $AgNO_3$ used as a silver precursor (1, 2.5, 5, 10 and 100 mM) were used. Very rapid formation of Ag nanoparticles was observed, as only minutes were necessary for the completion of the reaction. With the increasing concentration, red shift of the surface plasmon resonance peak was observed in the Vis spectra. According to photon cross-correlation spectroscopy results, the finest grain size distribution was obtained for the 2.5 mM sample. The transmission electron microscopy analysis of this sample has shown bimodal size distribution with larger crystallites with 100 nm size and smaller around 10 nm. The antibacterial activity was also the best for this sample so the positive correlation between good grain size distribution and antibacterial activity was found. The in-depth discussion of antibacterial activity with related works from the materials science point of view is provided, namely emphasizing the role of effective nanoparticles distribution within the plant extract or matrix. The antibacterial activity seems to be governed by both content of Ag nanoparticles and their effective distribution. This work contributes to still expanding environmentally acceptable field of green synthesis of silver nanoparticles.

• Corrosion Science and Technology
• /
• v.18 no.2
• /
• pp.55-60
• /
• 2019

Corrosion failure in the convection part of peak load boiler (PLB) of the district heating system led to water leakage. Herein, Internal Rotary Inspection System (IRIS) inspection was employed to examine wall thinning and the cause of leakage in the flue tube. The corrosive products of the turbulator and tube were investigated using scanning electron microscope combined with energy dispersive spectroscopy, X-ray diffraction, and inductively coupled plasma (ICP). Majority of the serious corrosion damage was observed near the turbulator located in the upper flue tube. ICP analysis of the boiler water revealed oxide formation of sodium chloride in the lower end part of the flue tube. A cross-sectional view of the turbulator revealed the presence of double-layers of the oxide film, indicating environmental change during operation associated with water leakage. The outer surface of the turbulator consisted of the acid oxides such as $NO_x$ and $SO_x$ along with sodium and chloride ions. Dew-point corrosion is hypothesized as the main cause for the formation of acid oxides in the region of contact of the flue tube and the turbulator.

• Safety and Health at Work
• /
• v.13 no.2
• /
• pp.141-147
• /
• 2022

Background: On the basis of its role for the development of occupational health research, information, good practices, the International Commission on Occupational Health (ICOH) launched the present survey to collect information on public health and prevention policies put in place by the governments of the countries in the world to contain the pandemic. Methods: A cross-sectional study was conducted through an online questionnaire focused on COVID-19 data, public health policies, prevention measures, support measures for economy, work, and education, personal protective equipment, intensive care units, contact tracing, return to work, and the role of ICOH against COVID-19. The questionnaire was administered to 113 ICOH National Secretaries and senior OSH experts. Collected data refer to the period ranging from the beginning of the pandemic in each country to June 30, 2020. Results: A total of 73 questionnaires from 73 countries around the world were considered valid, with a 64.6% response rate. Most of the respondents (71.2%) reported that the state of emergency was declared in their country, and 86.1% reported lockdown measures. Most of the respondents (66.7%) affirmed that the use of face masks was compulsory in their country. As for containment measures, 97.2% indicated that mass gatherings (meetings) were limited. Regarding workplace closing, the most affected sector was entertainment (90.1%). Conclusion: The results of this survey are useful to gain a global view on COVID-19 policy responses at country level.

• Journal of the Korea Society for Simulation
• /
• v.18 no.4
• /
• pp.219-225
• /
• 2009

The primary purpose of this study is to build computer models referring overall flow of complex and various semiconductor wafer manufacturing process and to implement a educational model which operates with a presentation tool showing device design. It is important that Korean semiconductor industries secure high competitive power on efficient manufacturing management and to develop technology continuously. Models representing the FAB processes and the functions of each process are developed for Seoul National University Semiconductor Research Center. However, it is expected that the models are effective as visually educational tools in Korean semiconductor industries. In addition, it is anticipated that these models are useful for semiconductor process courses in academia. Scalability and flexibility allow semiconductor manufacturers to customize the models and perform simulation education. Subsequently, manufacturers save budget.