• Journal of Korean Association for Spatial Structures
• /
• v.21 no.4
• /
• pp.23-30
• /
• 2021

In this paper, a twisted shape structure with an elevation form favorable to the resistance of vibration caused by wind loads is selected from among the forms of high-rise buildings. The analytical model is a square, triangular, and hexagonal plane with a plane rotation angle of one degree from 0 to 3 degrees per each story. As a result of the analysis, as the twist angle increased, story drift ratio is increased. Responses with different eccentricity rates were shown by analytical models. Therefore planar shapes designed symmetrically to the horizontal axis of X and Y are considered advantageous for eccentricity and torsion deformation. In the case of the bending moment of the column, the response was amplified in the column supporting the base floor, the roof floor, the floor in which the cross-section of the vertical member changes, and the floor having the same number of nodes as the base floor. Finally, the axial force response of the column is determined to be absolutely affected by the gravity load compared to the lateral load.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.8 no.4
• /
• pp.305-313
• /
• 1996

CTD measurements were conducted in the Nakdong estuary on the several sections or along-plume and cross-plume directions in 1993 and 1994. Internal Froude number Fi=0.22-0.35 in ebb tides and 0.14 in flood tides suggest that Nakdong river plume may go farther seawards in the along-plume direction with little mixing with the adjacent sea water after the construction of Nakdong river barrier. From Dadae-Po to Gaduk-Do section of cross-plume direction, three cores of low salinity were found. The main plume outflows from the newly made channel by cutting Ulsuk-Do after the construction of barrier. The low salinity core found near Gaduk-Do is the plume patch advected by tidal currents. Rossby deformation radius varied with the tidal cycle so that Coriolis effect is strengthened in flood tides to deepen the isohalines westwards to the Gaduk-Do site. Internal wavelike shape was found in the section of cross-plume direction during ebb tides. Richardson number of the section suggests the possibility of forming internal wave but more precise observations are necessary.

• Journal of the Korean association of regional geographers
• /
• v.16 no.2
• /
• pp.100-109
• /
• 2010

The study examines two different sites to analyze the difference of stream channel profile between two different landuse areas on Neponset River, Boston, MA. Landuse represents the current status of land in terms of human, agricultural or forest, industry and environmental activity types. According to the previous research, forest and urban area are significantly distinguished in chemical characteristic, shape and bed load of the stream. On the chosen sites, I look at the cross-section profile, the slope, velocity, and roughness of the channels. With the data collected at the site I determined the value for the channel bed material using Manning's equation, and compared with the result of HEC-RAS model with the cross-section profile data I measured. In the forest area, water surface elevation and bed material obtained through Manning's equation are very close to HEC-RAS model result. However, in the resident area the Manning's 'n' value calculated much higher than assumption which was considered as cobble whose 'n' value is 0.03-0.06. The difference could be caused by unusual steep elevation on the site and the dam present down further. With the steep elevation upside of dam, there is critical-depth condition occurs. The difference of Manning's 'n' value reflects the difference of depth. HEC-RAS model was run to analyze the difference and the result shows that depth is 0.36 much less than 0.688 what I computed when the Manning's n value is 0.03(cobble) instead of the result of the study (0.13292). Beside, dam is a major source of fragmentation and degradation of stream, and it's possibly inferred upstream water levels are increased and stream velocity is decreased. This study is meaningful for introduction of HEC-RAS in geography field to analyze different sites with channel bed material, and it is going to be used more actively to manage river and river side.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.7
• /
• pp.918-925
• /
• 2017

Multiple reflections on exterior equipment with complex shape on naval ships cause unexpectedly high Radar Cross Section (RCS) distributions, and the directions of reradiated electromagnetic waves are hard to predict. Therefore, the optimum arrangement of exterior equipments should be considered according to the Radar Absorbing Structure (RAS) method. In this paper, the optimum arrangement for exterior equipments was determined to reduce multiple reflections and RCS even with complex shapes. The sequential descending arrangement method was used to establish an optimum arrangement algorithm. An LCS-2 type model was selected for optimum exterior equipment arrangements. In order to reduce computational cost, RCS distributions and multiple reflection path analysis of exterior equipments was carried out to select exterior equipments for optimum arrangement, and an optimum arrangement was determined to find positions with minimum RCS values. Also, the RCS reduction effect was analyzed using detectable radar range.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.286-287
• /
• 2008

The determination of roll speeds in continuous rolling system is an important factor along with the design of roll profile and roll gap. The tensile force on the workpiece induces reduced cross section area and the compressive force induces wrinkles. To determine the optimal roll speeds of current rough rolling system for wire rod, FE analysis was performed. We could predict the workpiece shape and the stress level more precisely by considering the elasto-plastic behavior of workpiece. Also the efficient analysis methodology is presented to reduce the calculation time by combining the ALE and lagrangian method.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.449-452
• /
• 2009

This paper was designed to fabricate the miniature spur gear with pitch circle of 1.8 by hot extrusion process of mechanically alloyed Zn-22wt%Al powder at various temperature. The mechanical alloying was preformed for ball milled times of 8h, 16h and 32h by the planetary ball milling. Mechanically alloyed powders were compacted cylindrical performs. Extrusions of the miniature spur gear using the alloyed powder were carried out at different extrusion temperatures. The extruded spur gear was sintered for 2h at $350^{\circ}C$ in argon atmosphere. The friction between the die and the powdered billet and the internally different density due to complex product shape cause the internal crack. To overcome the mentioned problems, high dimensional accuracy at cross section of the spur gear and uniform Vickers hardness could be obtained by graphite lubricant and controlling holding time.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.8
• /
• pp.840-844
• /
• 2012

Roll forming process is a sheet metal forming process where the forming occurs with rolls in several steps, often from an undeformed sheet to a product ready to use. And each pair of forming rolls installed in a forming machine operates a particular role in making up the required final cross-section. This process used to many industry manufactures and recently apply to automotive industry. This study, FEM simulation applied bumper reinforcement using SHAPE-RF software and analyzed about total effective strain, longitudinal strain, thickness according to the roll-pass.

• Structural Engineering and Mechanics
• /
• v.9 no.4
• /
• pp.349-364
• /
• 2000

This paper aims to make a contribution to understanding which methods apply for structural analysis of beams prestressed with FRP cables. A parametric non-linear numerical analysis of simply supported beams has been performed. In this analysis the shape of the cross-section, the strength of concrete, the material adopted for the cables (steel, GFRP, CFRP), the prestressing system (bonded or unbonded prestressing) and the degree of prestressing were changed to collect a broad range of data which, the author contends, should cover the most frequent types of common practice. The output data themselves and their comparison allow us to suggest some rules that could be adopted when dealing with beams prestressed with these innovatory materials that have an elastic-brittle behaviour.

• Steel and Composite Structures
• /
• v.17 no.1
• /
• pp.83-103
• /
• 2014

The objective of this research is to study the ultimate moment capacity of the connections between steel I-beams and concrete-filled steel tube columns using different stiffener configurations. The main parameters considered are column cross section shape, square or circular, and filling the column with concrete. This analytical study includes finite element models using ANSYS program taking geometric and material nonlinearities into consideration. These models are verified against the experimental results obtained from previous researches and current design guides. The results show that using proper stiffener configuration affects the stress distribution through the connection and increases the ultimate moment capacity of the connections. Also, circular column is advantageous than the square column for all stiffener configurations and dimensions.

• KIEAE Journal
• /
• v.8 no.6
• /
• pp.63-70
• /
• 2008

Slim floor construction is becoming used throughout many countries. It combines the advantages of flat slab construction with significant inherent resistance to fire. The slim floor system with web openings leads to the reduction of its self-weight. Although the system has enough strength and stiffness, it is necessary to evaluate and improve the effects of dynamic vibration to be able to annoy the residents. Thus, this study evaluates the serviceability of vibration effects based on the dynamic test of five slim composite beams. Based on the experimental results, the initial stiffness and natural frequency of all specimens exhibit the similar trend regardless of the opening and the shape of cross section. The decrease in natural frequency is deeply related to the reduction in the stiffness of specimens and thus, it can be concluded that the damage of slim composite floor can be detected by the measurement of natural frequency instead of the load-carrying capacity and the stiffness.