• Geomechanics and Engineering
• /
• v.21 no.5
• /
• pp.489-501
• /
• 2020

This paper conducts a complicated coupled effective stress analysis of X-section-in-place concrete (XCC) pile installation and consolidation processes using the dual-stage Eulerian-Lagrangian (DSEL) technique incorporating the modified Cam-clay model. The numerical model is verified by centrifuge data and field test results. The main objective of this study is to investigate the shape effect of XCC pile cross-section on radial total stress, excess pore pressure and time-dependent strength. The discrepancies of the penetration mechanism and set-up effects on pile shaft resistance between the XCC pile and circular pile are discussed. Particular attention is placed on the time-dependent strength around the XCC pile shaft. The results show that soil strength improved more significantly close to the flat side compared with the concave side. Additionally, the computed ultimate shaft resistance of XCC pile incorporating set-up effects is 1.45 times that of the circular pile. The present findings are likely helpful in facilitating the incorporation of set-up effects into XCC pile design practices.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.285-288
• /
• 2003

The bending phenomenon during extruding one product using four billets can be obtain by the difference of hole diameters in the multi-hole container. The difference of hole diameter caused the difference of billet amount inserted in the die cavity. As results, it can bend during extruding products by the different amount of two billets and by the cohesion of billets in the porthole dies cavity. And the bending curvature can be controlled by the size of holes and billets. The experiments using aluminium material had been done for the rectangular and square curved tube product. The results of the experiment show that the curved aluminum tube product can be bended by the extru-bending process without the defects such as the distortion of section and the thickness change of the wall of tube and the folding and wrinkling. The curvature of product is affected by shape of cross section and the difference of billet diameters. It is known that the welding and extruding and bending can be done simultaneously in the die cavity when a rectangular hollow curved tube would be extruded by porthole dies using four different size billets made of aluminum material.

• Applied Microscopy
• /
• v.43 no.1
• /
• pp.14-20
• /
• 2013

The leopard danio, Danio rerio var. frankei is a spotted color morph of the zebrafish, Danio rerio caused by a pigment mutation. The structural differences of fertilized egg and egg envelope are poorly documented. To clarify this, we compared the fertilized egg morphology and ultrastructures of surface structures, the micropyle and the cross section of fertilized egg envelopes of zebrafish and leopard danio, variation species of zebrafish using a light and electron microscopes. Although the fertilized egg sizes were different, the external shapes of the fertilized eggs of two species couldn't be differentiated under the light microscope. The characteristics of fertilized eggs, such as a spherical shape, a non-adhesive quality and a large perivitelline space, were shown to be related to spawning habit. In ultrastructure of fertilized egg envelope, there is no morphological difference of micropyle between two species. By contrast, the ultrastructure and the numbers of knob-like structures and semihemisphere-like structures per unit area on the outer surface, and the number of lamellae of inner layer on the fertilized egg envelope section displayed definite species specificity. Collectively, our data indicate that the ultrastructure of fertilized egg envelope in the zebrafish could be differentiated by species variation.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.2
• /
• pp.57-68
• /
• 1998

For free vibration of monosymmetric thin-walled circular arches including restrained warping effect, the elastic strain and kinetic energy is derived by introducing displacement fields of circular arches in which all displacement parameters are defined at the centroid axis. The cubic Hermitian polynomials are utilized as shape functions for development of the curved thin-walled beam element having eight degrees of freedom. Analytical solution for free vibration behaviors of simply supported thin-walled curved beam element is presented by evaluating elastic stiffness and mass matrices. In order to illustrate the accuracy and practical usefulness of this study, analytical and numerical solutions for free vibration of circular arches are presented and compared with solutions analyzed by the FEM using straight beam element.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.2
• /
• pp.349-356
• /
• 2002

Cold-Formed C-section and Lipped C-section are commonly used as structural members of steel houses in Korea. Both are made of SGC41 steel. However, special Cold-Formed Sections with unique cross sectional shape have been developed and widely used in advanced countries. This research focused on the newly developed thin-walled Cold-Formed Sections which possess not only high strength and stiffness but also other advantages in construction. A series of compression tests was conducted to investigate the structural behavior of a compression member, including its load carrying capacity. Test results were compared with analytical study results.

• Steel and Composite Structures
• /
• v.33 no.5
• /
• pp.755-765
• /
• 2019

This study examined geometric and physical nonlinear analyses of beams and arches specifically from rolled profiles used in mining and underground constructions. These profiles possess the ability to create plastic hinges owing to their robustness. It was assumed that displacements in beams and arches fabricated from these profiles were comparable with the size of the structure. It also considered changes in the shape of a rod cross-section and the nonlinearities of the structure. The analyses were based on virtual unit moments, effective flexural rigidity of used open sections, and a secant method. The use of the approach led to a solution for the "after-critical" condition in which deformation increased with decreases in loads. The solution was derived for static determinate beams and static indeterminate arches. The results were compared with results obtained in other experimental tests and methods.

• Steel and Composite Structures
• /
• v.32 no.3
• /
• pp.411-422
• /
• 2019

Six shear-critical square tubed steel reinforced concrete (TSRC) columns using the high-strength concrete ($f_{cu,150}=86.6MPa$) were tested under constant axial and lateral cyclic loads. The height-to-depth ratio of the short column specimens was specified as 2.6, and the axial load ratio and the number of shear studs on the steel shape were considered as two main parameters. The shear failure mode of short square TSRC columns was observed from the test. The steel tube with diagonal stiffener plates provided effective confinement to the concrete core, while welding shear studs on the steel section appeared not significantly enhancing the seismic behavior of short square TRSC columns. Specimens with higher axial load ratio showed higher lateral stiffness and shear strength but worse ductility. A modified ACI design method is proposed to calculate the nominal shear strength, which agrees well with the test database containing ten short square TSRC columns with shear failure mode from this study and other related literature.

• Korean Journal of Human Ecology
• /
• v.18 no.3
• /
• pp.793-798
• /
• 2009

Hair cut is one of the best useful technical tool for hair styling. In this study using the rule of the layers of hair design, balanced for visual art, perceptual ability and form created by the principles of analysis and offer hair cuts and hair design of the representation of regions and even hair design as the basis of a student of Hair Beauty and all the people working in the field can create a variety of hair design puts the purpose to establish a basis. The result of this study can be outline as follows: First, the step line and the movement of the relationship between the law of the layers above and below the length of the same layer techniques, the same consists of a vertical cross-section of the overall round shape of the cut same layer is created and the appropriate volume and movement, the movement of low-layer round a little bit more feeling and expression is used when you want. High-layer used to want to move a lot of light and could see that. Second, the layer of the Law and over direction, lifting, section, the line control. weight control and analyzed by principle and the principle of the process of forming the written form was unknown. Third, hair design, the expansion of the expressive power of the law of the layers, and the section of the over direction depends on the presence of line control to express the length of the outline I had to, lifting the weight to adjust form controls, and the expression of Hair Design will be expanding the width. A hair designer, a layer style to create a zone he thought the law of the first layer formative area To further the reach will be a lot of research, leading up formative aspects of this research thesis do not have missing parts, or as a result of the Beauty of Hair Design and the width of a hair design education in the field can perform to help feed the reference materials that will be.

• Transactions of Materials Processing
• /
• v.13 no.8
• /
• pp.663-670
• /
• 2004

The bending phenomenon has been known to be occurred by the difference of velocity at the die exit. The difference of velocity at the die exit section can be obtained by the different velocity of billets through the multi-hole container. The difference of velocity at the die exit can be controlled by the two variables, the one of them is the different velocity of extrusion punch through the multi-hole container, the other is the difference of hole diameter of muliti-hole container. In this paper the difference of hole diameter is applied. So it can bend during extruding products because of the different amount of two billets when billets would be bonded in the porthole dies cavity. And the bending curvature can be controlled by the size of holes. The experiments with aluminum material for the curved tube product had been done for circular or rectangular curved tube section. The results of the experiments show that the curved tube product can be formed by the extru-bending process without the defects such as distortion of section and thickness change of wall of tube and folding and wrinkling. The curvature of product can be controlled by shape of cross section and the difference of billet diameters. And it is known that the bonding and extruding and bending process can be done simultaneously in the die cavity by the experiments that rectangular hollow curved tubes could be extruded by porthole dies with four different size billets made of aluminum material. And it shows that bending phenomenon can happen during extruding with for different billets from the analysis by DEFORM-3D.

• Journal of Welding and Joining
• /
• v.27 no.3
• /
• pp.73-79
• /
• 2009

This present paper investigated the mechanical properties and the microstructures of each penetration shapes classifying the conduction shape area and the keyhole shape area about electron beam welded 120(T)mm thick plated aluminum 5052 112H. As a result the penetration depth is increased linearly according to the output power, but the aspect ratio is decreased after the regular output power. In the conduction shape area, the Heat affected zone is observed relatively wider than the keyhole shape area. In the material front surface of the welded specimen, the width is decreased but the width in the material rear surface is increased. After the measuring the Micro Vikers Hardness, it showed almost similar hardness range in all parts, and after testing the tensile strength, the ultimate tensile strength is similar to the ultimate tensile strength of the base material in all the specimens, also the fracture point was generated in the base materials of all the samples. In the result of the impact test, impact absorbed energy of the Keyhole shape area is turned up very high, and also shown up the effect about four times of fracture toughness comparing the base material. In the last result of observing the fractographs, typical ductile fraction is shown in each weld metal, and in the basic material, the dimple fraction is shown. The weld metals are shown that there are no other developments of any new chemical compound during the fastness melting and solidification.