• Korean Journal of Food Science and Technology
• /
• v.16 no.2
• /
• pp.201-205
• /
• 1984

Some physicochemical properties of ginger root (Zingiber officinale) starch were compared with those of cross-linked corn starch. The ginger root starch that contained 23.5% amylose had a water-binding capacity of 99.1% and a B-type X-ray diffraction pattern. The optical transmittance of the ginger root starch suspension increased from $70^{\circ}C$ and showed a similar pattern to cross-linked corn starch. Solubility studies revealed that both ginger root and cross-linked corn starches had low swelling power and solubility in water up to $90^{\circ}C$, and reduced solubility in potassium hydroxide. Brabender amylograph data indicated that the ginger root starch (7%) had a relatively high initial pasting temperature $(81.5^{\circ}C)$ and was stable against heat and mechanical shear, which resembled to the cross-linked corn starch.

• International Journal of Aeronautical and Space Sciences
• /
• v.14 no.4
• /
• pp.398-407
• /
• 2013

Optical tomography was used to measure the pattern of spray cross-section. The maximum-likelihood estimation (MLE) algorithm was used to reconstruct the spray cross-section from the measured transmission rate of the spray. A swirl-type injector was used to form an optically dense spray, and the test was carried out in a high-pressure chamber, to control the pressure condition of the test site. Before the experiment, the reliability of the MLE-based reconstruction algorithm was verified, by comparing it with a conventional filtered back projection reconstruction (FBP) method. The MLE algorithm showed superior reconstruction of the image. In the spray patternation experiment, the results of the optical tomography and optical line patternator, which uses Mie scattering signal information, were compared. While measuring the cross-section of optically dense spray, the intensity of the scattering signal had attenuated to an uncorrectable level, which led to incorrect spray pattern measurement by the optical line patternator. However, reliable results were obtained by optical tomography, under the same condition. Finally, the pattern of the optically dense spray was measured at various chamber pressures, of up to 3 MPa. As the chamber pressure increased, the hollow cone-shaped swirl spray shrank, and the attenuation coefficient value of the inner region increased.

• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.377-381
• /
• 2008

Prism sheet of LCD BLU which depends on supply from Japan and U.S.A was studied by using Si anisotropic etching and injection molding technologies. First, the prism sheet was patterned on Si wafer through photolithography, and the best conditions of Si etching were determined through etching Si wafer with TMAH to obtain straight optimized zigzag patterns, and a cross pattern to provide light diffusion and concurrent focusing. The etch rate of TMAH was concluded to be constant for $25wt%-70^{\circ}C$ condition. Ni stamp of prism sheet was made by electrodeposition using patterned Si wafer, normal or fast H/C(Heating/Cooling) injections were carried out to fabricate prism sheet. It was known that fast H/C injection could fabricate prism sheet more accurately than normal injection. Zigzag patterns and the cross pattern showed higher transmissivity than the straight patterns because of light diffusion through diagonal direction. The fast H/C injection for zigzag patterns showed lower transmissivity than normal injection because there occurred more light diffusion through precise injection patterns, but the fast H/C injection for straight patterns showed only refraction without diffusion, causing lower transmissivity than normal injection.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.2
• /
• pp.364-372
• /
• 1994

Theoretical method for analyzing the radiation pattern of cross-type 5-patch rectangular microstrip antenna is presented. The equivalent circuit of the array antenna is represented by the conventional transmission line model and the radiation admittance derived from the equivalent circuit of the slitted parallel-plate waveguide filled with a dielectric. The calculated results for the radiation pattern are compared with the measured values.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.43-44
• /
• 2006

We have studied electro-optical characteristics and stability of liquid crystal director depending on electrode patterning of common electrode on top substrate in patterned vertical alignment (PVA) mode. In the present studies, new type of common electrode pattern was suggested to enhance a dark state by reducing interference area due to data signal. According to the simulation result, PVA device with new common electrode pattern contributed to Improvement of an aperture ratio.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2006.07a
• /
• pp.687-687
• /
• 2006

• New & Renewable Energy
• /
• v.3 no.3
• /
• pp.14-19
• /
• 2007

A flow channel model of a bipolar plate with varying cross-sectional area was newly designed for improving performance and efficiency of a PEM fuel cell stack. As a result, the varying cross-sectional area model showed poor uniformity in velocity distribution, however, maximum velocity in the flow path is about 30% faster than that of the uniform cross-sectional area model. The proposed varying cross-sectional area model is expected to diffuse operating fluids more easily into diffusion layer because it has relatively higher values in pressure distribution compared with other flow channel models. It is expected that the implementation of the varying cross-sectional area model can reduce not only the mass transport loss but also the activation loss in a PEM fuel cell, and open circuit voltage of a fuel cell can thus be increased slightly.

• Journal of Digital Convergence
• /
• v.16 no.4
• /
• pp.321-327
• /
• 2018

Applications have evolved with the evolution of smartphones, and the search structure is changing as well. In this study, we searched through various cases of cross platform and found out the search pattern and suggested correct usage method accordingly. As a result, the search structure for cross platform can be divided into persistent navigation, temporary navigation, and auxiliary navigation. Persistent navigation is available in a hierarchical structure using springboards, lists, galleries, and top menus. Temporary navigation can take advantage of drawers, toggle menus, and pie menus, while secondary navigation can provide the same experience across platforms using an accordion menu or scrolling.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.133-134
• /
• 2012

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.307-312
• /
• 2005

In this paper, the broadband FCMA(Folded Cross Monopole Antenna), which is the cross monopole antenna with the folded element, is presented. To investigate the broadband characteristics of FCMA the VSWR, the gain, and the radiation pattern are calculated in frequency between 1.75 GHz and 2.655 GHz. From the calculated result, it is shown that the presented folded cross monopole antenna has a excellent band characteristics than the existing cross monopole antenna. The presented antenna is conformed as a broadband antenna which can be used for the indoor antenna of PCS, WCDMA, Wibro, and satellite DMB band.