• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.7-12
• /
• 2004

Large-sized pins are usually used to lift and handle large low speed diesel engine crankshaft. There has then been a need to reduce and optimize the weight of the traditionally used pins. Making an hole by cutting the inside of the pin out was investigated in view of static and fracture strength. To compensate the stress increase caused by the introduction of the inner hole, the groove in the circumferential direction pre-existing on the pin is to be removed. Finite element analysis was carried out for both the original model and weight reduced model. Stress intensity factors for semi-elliptical defects assumed on the pin for the original model and weight reduced model was calculated using the ASME method and compared with the fracture toughness test result of the pin material. The diameter of the cutting hole for the revised model was determined based on the analysis results.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.401-402
• /
• 2006

All-surface, all-tooth machining and roll forming of cast iron have been used to manufacture the crankshaft position sensor wheel (CPSW). However, these methods pose many problems such as difficult processing, high material cost, and low tooth precision. Thus, we developed a sintered CPSW with an improved detection ability in order to resolve the problems related with the previous methods of manufacturing CPSW by simplifying the process flow and improving tooth precision. The sintering process is introduced in this study. We conducted an experiment to compare the sintered and roll formed products and analyzed the results to evaluate the reliability of the sintering process. Furthermore, we compared and analyzed stress and displacement in the sintered and roll formed products through the "Finite Element Method(FEM)". According to the experimental and FEM results, the sintered product showed satisfactory mechanical properties. It was less expensive to process and lighter and showed better quality than the roll formed product. The results of this study could be applied to design an optimum CPSW using the sintering process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1994.05a
• /
• pp.54-54
• /
• 1994

• Journal of Mechanical Science and Technology
• /
• v.16 no.7
• /
• pp.942-949
• /
• 2002

The use of a combined starter/generator integrated into the drive train of an automobile offers several possibilities for improvement of fuel economy The use of such a starter/generator system is made feasible by a switch from a 14 volts electrical system to a 42 volts system, however, the sizing of the components is not a trivial problem. This study combines a dynamic electromechanical model of the starter, battery and power electronics with the nonlinear mechanics of the piston/crankshaft system and a thermofluid model of the compression and expansion processes to investigate the cold start problem. The example involves the start of an eight cylinder engine at -25 degrees Celsius. This paper shows how the mechatronic V8 engine of an automotive starter/generator system for the startability works well.

• Tribology and Lubricants
• /
• v.22 no.6
• /
• pp.342-349
• /
• 2006

In this study, a dynamic behavior of rotor-bearing system used in CNG compressor has been investigated using the combined methodologies of finite elements and transfer matrices. The finite element is formulated including the field element for a shaft section and the point element for roller bearings. The Houbolt method is used to consider the time march for the integration of the system equations. The transient whirl response of rotating shaft supported on roller bearings is obtained, considering compression forces and unbalance forces at eccentric crank-pin part. And, the steady state displacements of the rotor are compared with a variation in stiffness coefficient of roller bearings. Results show that the loci of crankshaft considering unbalance forces and external compression forces are more severe in whirl motion than with only unbalance forces.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.90-99
• /
• 1996

To keep up with the regulation of OBD II(on board diagnostics II), many detection methods for engine misfire have been developed. Among them, the method of using the crankshaft speed fluctuation is the most noticeable in the point of view of lower cost and easier installation than any others. On the basis of the results obtained from the previous engine-dynamometer test, the integrating torque index (ITI) has been introduced. In this research, the instrumental and the interfacing systems to engine control unit(ECU) are developed for the vehicle test. Therefore, the vehicle and chassis-dynamometer test can be carried out in addition to the rough road test. From this test, the previousproposed method proved that it can be applied to the real vehicle.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1591-1598
• /
• 2002

This paper reports on the effects of crankshaft offset on the engine friction. The effects of crank offset are investigated through the theoretical analysis. In this study, the mathematical models are presented fer evaluationg the friction level of each engine parts. Crank offset influences on the side force acted on the piston pin and sliding speed of piston. Crank offset is very effective to reduce the piston skirt friction. With application of crank offset, total engine friction decreases at low engine speed, but that increase as engine speed increases.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.191-194
• /
• 2003

A crank throw, which is one of the part of crankshaft for a large diesel engine, is manufactured by both closed die forging and open die forging. For the improvement of productivity the open die forging method is usually adopted to manufacture it these days. In case of the open die forging for the crank throw, a preform shape is very important because it seriously affects final dimensions of the product. The purpose of this study is to investigate affective factors of the preform to obtain a good shape of final product through simulation and the results are compared to downsized lead experiments.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.275-282
• /
• 2004

The engine bearing transmits the powers from cylinder to crankshaft with small clearance between con-rod and crankpin. The minimum oil film thickness is a significant parameter in the operation of bearing. The contact pressure of bearing should be considered for the reason that elastic deformation of bearing be caused by contact pressure of bearing. There are important factors which are maintaining of minimum oil film thickness expecting of the length of maximum and minimum oil film thickness with changing of the loads to keep running normally. Furthermore, this study is very crucial to develop the design of engine bearing and crankshaft system.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.110-119
• /
• 1992

Crank pin temperatures were measured and analyzed to find out practical method which can predict the engine bearing reliability. The measuring points were determined to be near the MOFT region and far from that by theoretical calculation. The effect of engine running condition, oil temperature, the change of oil circuit into bearing and crankshaft endplay on crank pin temperature were experimentally tested. The result obtained was as following. The crank pin temperature was dependent on oil film thickness and directly influenced by the change of test condition. Also, the length of the crankshaft endplay was confirmed to be critical to connecting rod bearing failure. In conclusion, we found that the measurement method of crank pin temperature can be used for predicting the engine bearing reliability.