• Journal of Drive and Control
• /
• v.9 no.1
• /
• pp.10-17
• /
• 2012

Nowadays, the demand of energy saving is increasing more and more while the natural resources have been exhausted. Besides, the emission gas caused by vehicles has been being a serious environment problem. Therefore, many studies have been carried out, especially focusing on braking energy regeneration, in order to save energy as well as reduce emission of mobile vehicles. In this paper, we propose a closed-loop hydrostatic transmission for braking energy regeneration with two configurations to reduce the energy consumption by recovering the braking energy. The effectiveness of the proposed system was verified by simulation. The simulation results indicated that the pressure coupling configuration gave better performance in comparison to flow coupling configuration about 40.8%, 61.7% and 53.8% reduction of fuel consumption in 10 mode, 10 mode modified profile and highway schedules, respectively.

• Proceedings of the KIEE Conference
• /
• 1998.07b
• /
• pp.522-524
• /
• 1998

In this paper, the cross-coupling controller with fuzzy logic for AGV is developed, Cross-coupling control directly minimizes orientation' error by coordinating the motion of the two drive wheels and uses PI controller for compensation. But, the transient response of PI controller results in deviation from trajectory. The Fuzzy Cross-coupling controller enhances transient performance without steady-state error. The performance of the above controller is demonstrated by simulation and is compared with that of PI controller.

• Journal of the Korean Society of Safety
• /
• v.37 no.3
• /
• pp.45-51
• /
• 2022

This paper focuses on a recently proposed asymmetric base-isolation coupling control system (ABiCS) for the vibration control of adjacent twin buildings. The ABiCS consists of inter-story diagonal dampers, a connecting damper between the two buildings, and a seismic isolation device at the base floor of one building. To investigate the control characteristics of ABiCS, a parametric study was performed by numerically simulating the 20-story twin buildings. In the parametric study, the control capacities of the inter-story diagonal dampers, connecting damper, and seismic isolation device were considered as varying parameters. The parametric study results indicate that the connecting damper between the two buildings reduces the responses of both buildings only at optimal or near-optimal capacity. In addition, adjusting the stiffness of the base isolation is found to be the most effective method for improving seismic performance and achieving cost-effectiveness. Accordingly, we presented a scenario-based performance improvement approach in which reducing the stiffness of the base isolation device could be an effective technique to improve the seismic performance of both buildings. However, note that checking the maximum allowable displacement of the base isolation device is essential.

• Structural Engineering and Mechanics
• /
• v.15 no.2
• /
• pp.181-198
• /
• 2003

Six large scale models of conventionally reinforced concrete coupling beams with span/depth ratios ranging from 1.17 to 2.00 were tested under monotonically applied shear loads to study their nonlinear behavior using a newly developed test method that maintained equal rotations at the two ends of the coupling beam specimen and allowed for local deformations at the beam-wall joints. By conducting the tests under displacement control, the post-peak behavior and complete load-deflection curves of the coupling beams were obtained for investigation. It was found that after the appearance of flexural and shear cracks, a deep coupling beam would gradually transform itself from an ordinary beam to a truss composed of diagonal concrete struts and longitudinal and transverse steel reinforcement bars. Moreover, in a deep coupling beam, the local deformations at the beam-wall joints could contribute significantly (up to the order of 50%) to the total deflection of the coupling beam, especially at the post-peak stage. Finally, although a coupling beam failing in shear would have a relatively low ductility ratio of only 5 or even lower, a coupling beam failing in flexure could have a relatively high ductility ratio of 10 or higher.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1995.04a
• /
• pp.869-879
• /
• 1995

The new field of learning control develops controllers that learn to improve their performance at executing a given task, based on experience performing this task. The simplest forms of learning control are based on the same concept as integral control, but operating in the domain of the repetitions of the task. In the previous paper, I had studied the use of such controllers in a decentralized system, such as a robot with the controller for each link acting independently. The basic result of the paper is to show that stability of the learning controllers for all subsystems when the coupling between subsystems is turned off, assures stability of the decentralized learning in the coupled system, provided that the sample time in the digital learning controller is sufficiently short. In this paper, we present two examples. The first illustrates the effect of coupling between subsystems in the system dynamics, and the second studies the application of decentralized learning control to robot problems. The latter example illustrates the application of decentralized learning control to nonlinear systems, and also studies the effect of the coupling between subsystems introduced in the input matrix by the discretization of the system equations. The conclusion is that for sufficiently small learning gain, and sufficiently small sample time, the simple learning control law based on integral control applied to each robot axis will produce zero tracking error in spite o the dynamic coupling in the robot equations. Of course, the results of this paper have much more general application than just to the robotics tracking problem. Convergence in decentralized systems is seen to depend only on the input and output matrices, provided the sample time is suffiently small.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.8
• /
• pp.1480-1486
• /
• 2002

In this study, the cross-coupling control (CCC) with three new features is proposed to maintain contour precision in high-speed nonlinear contour machining. One is an improved contour error model that provides almost exact calculation of the errors. Another is the utilization of variable controller gains based on the instantaneous curvature of the contour and the variable command. For this scheme, a stability is analyzed. As a result, the stability region is obtained, and the variable gains are decided within that region. The other scheme in the proposed CCC is a real-time feedrate adaptation module to regulate cutting force fur better surface finish through regulation of material removal rate (MRR). The simulation results show that the proposed CCC system can provide better precision than the existing method particularly in high-speed machining of nonlinear contours.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.137-138
• /
• 2006

This paper proposes a controller design analysis for three-axis CNC systems considering both contouring and tracking performance. The proposed analysis inclusively combines axial controllers for each individual feed drive system together with cross-coupling controller at the beginning design stage as an integrated manner. These two controllers used to be separately designed and analyzed since they have different control objectives. The proposed scheme includes a stability analysis for the overall control system and a performance analysis in terms of contouring and tracking accuracy. Computer simulation is performed and the results show the validity of the proposed methodology.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.3
• /
• pp.66-73
• /
• 2003

In this study, a methodology of synchronous control which can be applied to position synchronization of a two-axis rotating system is developed. Based on coupling structure, the synchronous control system is composed of disturbance observer, speed and synchronous controllers. The speed controller is designed to follows speed reference. The disturbance observer is designed to restrain synchronous error. In addition, the synchronous controller is designed for a viewpoint of accurate synchronization in lead compensation law. The effectiveness of the proposed method is verified through simulation.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2000.08a
• /
• pp.113-116
• /
• 2000

This paper analyzes the singularity of an anthropomorphic robot associated with joint and operational stiffness generation from muscle stiffness. The singularity analysis is made simply based on the signs of the actual and the desired coupling joint stiffness. First, the relationships of the muscle stiffness and the actual joint stiffness, and the operational stiffness and the desired joint stiffness are examined. Second, according to the sign restriction on the actual coupling joint stiffness, the operational space is divided into the semi-singular(SS), the regular(R), and the semi-regular(SR) regions. Third, from the sign comparison of tile actual and the desired coupling joint stiffness, the sufficient condition for the semi-singularity in operational stiffness generation is derived. The limitation on the allowable operational stiffness when a task point belongs to SS, R, and SR regions is also discussed. Simulation results are given.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.156.1-156
• /
• 2001

It is observed that if the 2-gimballed seeker is stabilized using rate gyros mounted along its primary axis, line of sight change measured in the seeker is induced by the rolling due to the bank-to-turn(BTT) steering as well as the actual change. This body-coupling within BTT homing includes the spurious target maneuver effect and the coupling loop due to the rate gyro misalignment. In this paper we formulates the linear BTT homing loop model with a 2-gimballed seeker including those body-coupling effects. With the model, we analyze the effects of the couplings, and show that the roll rate coupling to the rate gyro for the stabilztion of gimbal could seriously deteriorate the homing loop stability. And we propose a direct linear compensator for the coupling to recover the stability.