• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.311-318
• /
• 2006

CFD simulation is a tool very useful to predict the generation and absorption of the contaminant from the construction materials for the single room condition. However, there is a limit in multi-room simulation for analyzing air movement and contaminant concentration at the condition that the door of each room was closed. A lot of network simulation tool were developed which can used to analyze the mass transfer and contaminant concentration as results in the multi-room condition. However, existing network simulation method was not able to analyze the change of the heating and cooling load with the ventilation as though the change of the indoor air-pollution density was predictable. In this study, new approach to predict heating/cooling load and indoor contaminant concentration will be reviewed. New indoor contaminant concentration module reviewed in this study wad coupled with existing ESP-r network simulation method. The validity of new approach will be analysed for comparison the results of simulation and field measurement results.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.6
• /
• pp.543-550
• /
• 2003

In order to saving the energy for HVAC system of buildings, utilization of wind-induced cross ventilation is thought to be promising. However, utilization of natural ventilation alone is not sufficient for maintaining the human thermal-comfort such as in hot and humid regions. A hybrid air conditioning system with a controlled natural ventilation system, or combination of natural ventilation with mechanical air conditioning is thought to overcome the deficiency of wind-driven cross ventilation and to have significant effects on energy reduction. This paper describes a concept of hybrid system and propose a new type of hybrid system using radiational cooling with wind-induced cross ventilation. Moreover, a radiational cooling system is compared with an all-air cooling system. The characteristics of the indoor environment will be examined through CFD (Computational Fluid Dynamics) simulation, which is coupled with a radiation heat transfer simulation and with HVAC control in which the PMV value for the human model in the center of the room is controlled to attain the target value.

• Journal of the Korean Vacuum Society
• /
• v.8 no.4A
• /
• pp.476-481
• /
• 1999

Characteristics of platinum dry etching were investigated in a cryogenic magnetized inductively coupled plasma (MICP). The problem with platinum etching is the redeposition of sputtered platinum on the sidewall. Because of the redeposits on the sidewall, the etching of patterned platinum structure produces feature sizes that exceed the original dimension of the PR size and the etch profile has needle-like shape [1]. The main object of this study was to investigate a new process technology for fence-free Pt etching As bias voltage increased, the height of fence was reduced. In cryogenic etching, the height of fence was reduced to 20% at-$190^{\circ}C$ compared with that of room temperature, however the etch profile was not still fence-free. In Ar/$SF_6$ Plasma, fence-free Pt etching was possible. As the ratio of $SF_6$ gas flow is more than 14% of total gas flow, the etch profile had no fence. Chemical reaction seemed to take place in the etch process.

• Transactions of Materials Processing
• /
• v.23 no.8
• /
• pp.475-481
• /
• 2014

Water quenching is one method of cooling after hot forming, which is presently being used for the manufacturing of automobile parts. The formed parts at room temperature are heated and then cooled rapidly in a water bath to produce high strength. The formed parts may undergo excessive thermal distortion during the water quench. In order to predict the distortion during water quenching, a coupled thermo-mechanical simulation is needed. In the current study, the simulation of heating and cooling of boron steel cylinders was performed. The material properties for the simulation were calculated from JMatPro, and the convective heat transfer coefficient was obtained from experimental tests. The results show that the thermal distortion and the residual stresses are well predicted by the coupled simulation.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.163-167
• /
• 2002

We have fabricated planar-type single-layer second-order high-Tc SQUID gradiometers. The devices consisted of symmetrically designed three parallel-connected square pickup loops that were directly coupled to the SQUID. $YBa_2$$Cu_3$$O_{7}$ film was deposited on $SrTiO_3$ substrate by a PLD system and patterned into a device by the photolithography with ion milling technique. Junctions of the SQUID were either step-edge or bicrystal type. All the structures were formed on a 10 mm $\times$ 5 mm substrate. Balancing of the gradiometer was achieved by adjusting the width of the central pickup loop. The gradiometer noise was measured both inside and outside a magnetically shielded room. Details of the results will be discussed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1568-1570
• /
• 2009

Nanocrystalline silicon thin films were deposited using an internal-type inductively coupled plasma-chemical vapor deposition at room temperature by varying the bias power to the substrate and the structural characteristics of the deposited thin film were investigated. The result showed that the crystalline volume fraction was decreased with the increase of bias power. At the low bias power range of 0~60 W, the compress stress in the deposited thin film was in the range of -34 ~ -77 Mpa which is generally lower than the residual stress observed for the nanocrystalline silicon thin films deposited by capacitively coupled plasma.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.288-297
• /
• 2008

Recent research efforts on study of silicon photonics utilizing stimulated Raman scattering have largely overlooked temperature effects. In this paper, we incorporated the temperature dependences into the key parameters governing wave propagation in silicon waveguides with Raman gain and investigated how the temperature affects the solution of the coupled-mode equations. We then carried out, as one particular application example, a numerical analysis of the performance of wavelength converters based on stimulated Raman scattering at temperatures ranging from 298 K to 500 K. The analysis predicted, among other things, that the wavelength conversion efficiency could decrease by as much as 12 dB at 500 K in comparison to that at the room temperature. These results indicate that it is necessary to take a careful account of temperature effects in designing, fabricating, and operating Raman silicon photonic devices.

• Mass Spectrometry Letters
• /
• v.12 no.3
• /
• pp.106-111
• /
• 2021

Several pretreatment methods have been developed to reduce the inorganic arsenic, which is known to be highly harmful to humans, among various arsenic species present in hijiki and rice. The pretreatment methods were selected and developed as methods that can be non-harmful even after treatment and easily applied. Hijiki was applied by two methods. One was soaking in water at room temperature for various durations and the other was boiling of it in water for a short period of time. Rice was soaked in water with different rice-to-water ratios for various durations. The most effective method that reduced the inorganic arsenic in hijiki was to repeat parboiling for 5 minutes twice, which led to 79% reduction of the inorganic arsenic in it. In the case of rice, soaking for 24 hours at the ratio of 1:5 (rice:water) resulted in 51% reduction of inorganic arsenic in rice.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.1
• /
• pp.1-5
• /
• 2008

ZnS is an attractive material for future optical and electrical devices since it has a direct and wide band gap to provide blue emission at room temperature. In this study, inductively coupled $BCl_3/Ar$ plasma was used to etch ZnS:Mn thin films. The maximum etch rate of 164.2 nm/min for ZnS:Mn was obtained at a $BCl_3(20)/Ar(80)$ gas mixing ratio, an rf power of 700 W, a dc bias voltage of -200V, a total gas flow of 20 sccm, and a chamber pressure of 1Pa. The etch behaviors of ZnS:Mn thin films under various plasma parameters showed that the ZnS:Mn were effectively removed by the chemically assisted physical etching mechanism. The surface reaction of the ZnS:Mn thin films was investigated by X-ray photoelectron spectroscopy. The XPS analysis revealed that Mn had detected on the surface ZnS:Mn etched in $BCl_3/Ar$ plasma.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.16 no.3
• /
• pp.89-99
• /
• 2008

Indoor ozone has received attention because of its well-documented adverse effects on health. In addition to the inherently harmful effects of ozone, it can also initiate a series of reactions that generate potentially irritating oxidation products, including free radicals, aldehydes, organic acids and secondary organic aerosols (SOA). Especially, ozone reacts actively with terpene. The overarching goal of this work was to better understand ozone and terpene distributions within rooms. Towards this end, the paper has two parts. The first describes the development of a cylindrical test chamber that can be used to obtain the second order rate constant $(k_b)$ for the bi-molecular chemical reaction of ozone and terpene in the air phase. The second consists of model room experiments coupled with Computational Fluid Dynamics (CFD) analysis of the experimental scenarios to obtain ozone and terpene distributions in various turbulent flow fields. The results of CFD predictions were in reasonable agreement with the experimental measurements.