• Journal of Electrochemical Science and Technology
• /
• v.12 no.4
• /
• pp.398-405
• /
• 2021

To fabricate a full-scale pilot model of the cost-effective Na-(Ni,Fe)Cl₂ cell, a Na-beta-alumina solid electrolyte (BASE) was developed by applying a one-step synthesis cum sintering process as an alternative to the conventional solid-state reaction process. Also, Fe metal powder, which is cheaper than Ni, was mixed with Ni metal powder, and was used for cathode material to reduce the cost of raw material. As a result, we then developed a prototype Na-(Ni,Fe)Cl₂ cell. Consequently, the Ni content in the Na-(Ni,Fe)Cl₂ cell is decreased to approximately (20 to 50) wt.%. The #1 prototype cell (dimensions: 34 mm × 34 mm × 235 mm) showed a cell capacity of 15.9 Ah, and 160.3 mAh g^-1 (per the Ni-Fe composite), while the #2 prototype cell (dimensions: 50 mm × 50 mm × 335 mm) showed a cell capacity of 49.4 Ah, and 153.2 mAh g^-1 at the 2^nd cycle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.143-145
• /
• 1996

A new method of fabricating 3-dimensional patterns on single crystal silicon is presented in this paper. The method utlizes both chemical and mechanical reactions to make patterns with dimensions of few microns in width and submicron in height. The primaryadvantage ofthis new method over conventional methods of making patterns on silicon lies in its cost effectiveness and speed. The process introduced in this paper is a maskless process and does not reauire expensive capital investment. It is expected that this method can be employed for flexible and cost effective fabrication of micro-machine components in MEMS application.

• International conference on construction engineering and project management
• /
• 2015.10a
• /
• pp.72-76
• /
• 2015

Capital project benchmarking requires an effective cost normalization process to compare cost performance of projects accomplished in different time and location. Existing cost normalization approaches have been established based on the assumption that all required information for cost normalization is fully identified once a project is completed. Cost normalization, however, is sometimes required to evaluate phase-level outcomes of an ongoing project where the required information is not fully available. This paper aims to provide a cost normalization procedure for phase-based performance assessment. The procedure consists of three normalization steps: currency conversion, location adjustment, and time adjustment considering various scenarios where the required information is not fully identified. This paper also presents how the cost normalization procedure has been applied to the 10-10 Performance Assessment Program, which is a phase-based performance assessment system developed by the Construction Industry Institute (CII). Both researchers and industrial professionals can apply the cost normalization procedure to studies and practices regarding to cost estimation, feasibility analysis, and performance assessment.

• IE interfaces
• /
• v.18 no.4
• /
• pp.477-484
• /
• 2005

This paper is concerned with the life-cycle cost(LCC) of the urban transit system which was developed by KRRI and is now under test in Gyeongsan, Korea. Its reliability, availability and maintainability(RAM) were analyzed. LCC is the core part of analyzing the total cost of acquisition and ownership of a system. LCC analysis of a system is the most effective when it is applied in the it's early design phase. In this paper, we present IEC 60300-3-3(Life Cycle Costing) in detail and propose how to apply LCC in assessing the urban transit system according to RAM process. This case study demonstrates that reliability management system is very effective in reducing the operating cost of subway corporations in Korea.

• The Journal of Society for e-Business Studies
• /
• v.7 no.2
• /
• pp.129-141
• /
• 2002

This paper deals with the collaborative procurement process in a two-echelon supply chain that a manufacturing company and a contractor are connected through the information system. The real time information about inventory and production processing becomes available through this information system. We raise two issues related to the collaborative procurement process. First, we propose a VMI(Vendor-Managed Inventory) type of the procurement policy which focuses on the cost minimization for the total supply chain rather than individual companies. Second, based on the simulation study, we demonstrate that a collaborative procurement process is more cost-effective over classical procurement processes such as (Q, r). The result obtained in this paper can be applied to the quantitative evaluation of the cost saving effect when companies build the information sharing based, collaborative procurement system.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.18 no.36
• /
• pp.121-131
• /
• 1995

The purpose of a business's existence is to make profit. The objective of business can be attained through the most profitable activities such as the improvement of productivity, quality and the reduction of the manufacturing cost. In order to produce the goods with above said goal, it can be achieved by inducing and improving the manufacturing process. In this viewpoint, We'd like to develope an algorithm for improving productivity, quality and cutting the manufacturing cost under the limitation of the resources. This paper showed a practical method which gradually improves three factors [productivity, quality and cost-down] by calculating the effective value of single and multi process mutually.

• Economic and Environmental Geology
• /
• v.37 no.1
• /
• pp.49-59
• /
• 2004

The concectration and distribution of contaminants obtained from a contaminated land investigation or an environmental geochemistry survey constitutes the basis of a decision-making process on environmental policies or of scientific researches. As the quality of data determines the reliability of the result, the investigation plan should be adjusted according to the purpose of the investigation. In general, the effort to improve the data quality had been focused mainly on the QA/QC procedures in laboratories. The rapid progress of analytical instrument has also contributed toward improving the analytical precision to a sacrificable degree. Nevertheless, in many cases, it is not the analytical precision that needs improvement for the better precision of overall measurement process: it is rather during the sampling process in the field that is responsible for the poor precision. To assess the data quality on a measured value, ISO recommends to provide information on "measurement uncertainty" along with the measured value. The measurement uncertainty in an environmental measurement context can be explained as the statistical number that expresses the degree of the uncertainty stemming from the sampling and analytical procedures. There is a cost involved in order to improve the precision of sampling and analytical methods so as to decrease the degree of measurement uncertainty. The economical point of compromise in an investigation planning can be achieved when the allowable degree of uncertainty has been set before-hand. The investigation can then be planned accordingly not to exceed the uncertainty limit. Furthermore, if the measurement uncertainty estimated from the preliminary investigation can be separated into sampling and analytical uncertainties, it can be used as a criterion where the resources for the investigation should be allotted cost-effectively to reinforce the weakest link of the whole investigation process. This paper aims to present a method of estimating the level of measurement uncertainty of a measured contamination concentration at a site used as an example and to show how the estimated uncertainty can be applied to serve the particular purpose of an investigation.

• International conference on construction engineering and project management
• /
• 2011.02a
• /
• pp.182-186
• /
• 2011

Early cost estimates are important to decision-making for a construction project. Moreover, the possibility of reducing the project cost is getting less as the project is progressed. Case-based reasoning (CBR), which can be viewed as an effective method for early cost estimating, is widely utilized recently. Early cost estimates using CBR have advantages over the traditional ones as they produce reasonable outputs and self-studying is possible by simply adding new cases. Case-based reasoning is composed of a cycle of retrieve, reuse, revise, and retain process. However, in the majority of research cases, they are focused on how to retrieve the similar cases, instead of revising the cases which is expected to increase accuracy results of cost estimation. This research suggests a method of revising retrieved similar cases in a GA-CBR cost model which is widely studied and utilized for early cost estimating recently. To validate the proposed method, case study is conducted based on Korean public apartment projects.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.340-343
• /
• 2007

We describe the DuPont Displays full color OLED printing and materials technologies. The process is more cost-effective and scalable than thermal evaporation through shadow masks. The materials lifetime is sufficient for most portable applications and is nearing that required for stationary displays. Recently, 4.3" WQVGA displays were demonstrated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.207-210
• /
• 2003

As reviewing of current trend on PC connection details, owing to effective stress transfer in the connection, it grow to increase that use of mechanical splices, reinforcements or welded splices, and prestressing. However such devices as reinforcement, mechanical splices entail not only more cost resulted from materials but also extra construction process so as to cause PC used method to lower competition against conventional method. Therefore more enhanced connection details which help working process simplified and construction cost reduced. In this research, as replace 9.3mm 7strand for reinforcement, it is attempt to devise connection detail which makes workability improve and confirm effective stress transfer in the region of connection. The experimental research is proceeded by partial tension test of specimen. The splice lengths of 7strand is decided to be variations. The flexural capability is verified to depend on spice length. An an appropriate splice length could be also determined as a precedent research on improving PC connection detail.