• 한국재료학회지
• /
• 제9권5호
• /
• pp.533-537
• /
• 1999

ATO(Sb doped $SnO_2$) thin films whose thicknesses were 600, 1100 and $2100\AA$ were prepared by DC magnetron sputtering method. They showed the lowest resistivity at DC sputtering power 0.24kW and had lower resistivity with increasing thickness. The power dependence of resistivity among ATO thin films was also different with thickness. The increase of carrier concentration in ATO thin films was responsible for the decrease of resistivity with thickness increase. ATO thin films which were prepared at 30sccm oxygen flow rate showed a great change of sheet resistance under 1M HCl solution. The investigation of SAM(Scanning Auger Microprobe) revealed that oxygen atomic percentage on the surface of ATO thin films was changed. The decrease of sheet resistance also occurred when ATO thin films, prepared at 30sccm oxygen flow rate, were exposed to air for a long period of time. For this reason, it was considered that the desorption of oxygen on ATO surface was accelerated by HCl.

• 한국재료학회지
• /
• 제24권3호
• /
• pp.123-128
• /
• 2014

To realize high-performance thin film solar cells, we prepared CIGS by the co-evaporation technique on both sodalime and Corning glass substrates. The structural and efficient properties were investigated by varying the thickness of the Mo:Na layer, where the total thickness of the back contact was fixed at 1${\mu}m$. As a result, when the Mo:Na thickness was 300 nm on soda-lime glass, the measured Na content was 0.28 %, the surface morphology was a plate-like compact structure, and the crystallinity by XRD showed a strong peak of (112) preferential orientation together with relatively intense (220) and (204) peaks as the secondary phases influenced crystal formation. In addition, the substrates on soda-lime glass effected the lowest surface roughness of 2.76 nm and the highest carrier density and short circuit current. Through the optimization of the Mo:Na layer, a solar conversion efficiency of 11.34% was achieved. When using the Corning glass, a rather low conversion efficiency of 9.59% was obtained. To determine the effects of the concentration of sodium and in order to develop a highefficiency solar cells, a very small amount of sodium was added to the soda lime glass substrate.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 1995년도 춘계연구발표회 논문개요집
• /
• pp.110-111
• /
• 1995

• 한국품질경영학회:학술대회논문집
• /
• 한국품질경영학회 1998년도 The 12th Asia Quality Management Symposium* Total Quality Management for Restoring Competitiveness
• /
• pp.51-60
• /
• 1998

An experience of suggestion system was reported in this paper for the purpose of investigating effective factors of suggestion system at the Suwon Plant of Samsung Corning, Inc. in Korea. Suggestion system is a formal attempt in which employees make suggestions from ideas and thinkings. With the effective system, the company can achieve goals on the improvement of the working processes and products. At Suwon Plant, TPM is connected to both corporate vision and suggestion system: the former is the management concept and the latter is an operational tool. Linked to TPM, suggestion system is found to be effective owing to the factors such as strong support of top management, high job involvement, extensive participation and speedy, convenient evaluation procedure.

• 한국세라믹학회지
• /
• 제33권4호
• /
• pp.441-447
• /
• 1996

Sb doped SnO2(ATO:Antinomy doped Tin Oxide) thin films were prepared by a DC magnetron spttuering method using oxide target and the deposition characteristics were investigated. The experimental conditions are as follows :Ar flow rate : 100 sccm oxygen flow rates ; 0-100 sccm deposition temperature ; 250 -40$0^{\circ}C$ DC sputter powder ; 150~550 W and sputtering pressure ; ; 2~7 mTorr. Deposition rate greatly depends not on the deposition temperature but on the reaction pressure oxygen flow rate and sputter power,. when the sputter powder is low ATO thin films with (110) preferred orientation are deposited. And when the sputter power is high (110) prefered orientation appeares with decreasing of oxygen flow rate and increasing of suputte-ring pressure.

• 한국광학회지
• /
• 제12권6호
• /
• pp.460-462
• /
• 2001

밀봉재를 사용하는 적외선 렌즈 마운트를 분석하고, 3-5$\mu\textrm{m}$에서 작동하는 전방 관측 적외선 열상장비의 대물렌즈인 직경 117mm의 Si 렌즈 마운팅 설계에 적용하였다. 밀봉재료는 Dow Corning 사의 heat cure 타입인 577 primerless Silicone Adhesive(MIL-PRF-23586F)을 이용하였으며, 마운트 재질로는 Al 6061을 사웅하였다. 이론적으로 렌즈와 마운트간의 간격은 -40~+6$0^{\circ}C$의 적용 온도환경에 대하여 250$\mu\textrm{m}$ 이상이 되어야 함을 알 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2008년도 제34회 동계학술대회 초록집
• /
• pp.114-114
• /
• 2008

• Journal of Chest Surgery
• /
• 제54권6호
• /
• pp.460-465
• /
• 2021

Background: Metastasis and recurrence of primary cancer are the main causes of cancer mortality. Disseminated tumor cells refer to cancer cells that cause metastasis from primary cancer to other organs. Several recent studies have suggested that circulating tumor cells (CTCs) are associated with the clinical stage, cancer recurrence, cancer metastasis, and prognosis. There are several methods of isolating CTCs from whole blood; in particular, using a membrane filtration system is advantageous due to its cost-effectiveness and availability in clinical settings. In this study, an animal model of lung cancer was established in nude mice using the human large cell lung cancer cell line H460. Methods: Six-week-old nude mice were used. The H460 lung cancer cell line was injected subcutaneously into the nude mice. Blood samples were obtained from the orbital area before cell line injection, 2 weeks after injection, and 2 weeks after tumor excision. Blood samples were filtered using a polycarbonate 12-well Transwell membrane (Corning Inc., Corning, NY, USA). An indirect immunofluorescence assay was performed with the epithelial cell adhesion molecule antibody. The number of stained cells was counted using fluorescence microscopy. Results: The average size of the tumor masses was 35.83 mm. The stained cells were counted before inoculation, 2 weeks after inoculation, and 2 weeks after tumor excision. Cancer cells generally increased after inoculation and decreased after tumor resection. Conclusion: The CTC detection method using the commercial polycarbonate 12-well Transwell (Corning Inc.) membrane is advantageous in terms of cost-effectiveness and convenience.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.273-277
• /
• 2003

A general process of electronic assembly is composed of a series of geometric alignments and bonding/screwing processes. After assembly, the function is tested in a following process of inspection. However, assembly of micro-optic devices requires both processes to be performed in equipment. Coarse geometric alignment is made by using vision and optical function is improved by the following fine motion based on feedback of tunable laser interferometer. The general system is composed of a precision robot system for 3D assembly, a 3D vision guided system for geometric alignment and an optical feedback system with a tunable laser. In this study, we propose a new fast alignment algorithm of micro-optic devices for both of visual and optical alignments. The main goal is to find a fastest alignment process and algorithms with state-of-the-art technology. We propose a new approach with an optimal sequence of processes, a visual alignment algorithm and a search algorithm for an optimal optical alignment. A system is designed to show the effectiveness and efficiency of the proposed method.

• 한국세라믹학회지
• /
• 제33권5호
• /
• pp.514-518
• /
• 1996

Sb doped SnO2(ATO: Antinomy doped Tin Oxide) thin films were prepared by a DC magnetron spttuering method using an oxide target and the electrical characteristics of ATO films were investigated. The experimen-tal conditions are as follows :Ar flow rate ; 0~100 sccm deposition tempera-ture ; 250~40$0^{\circ}C$ DC sputter powder ; 150~550W and sputteing pressure ; 2~7 mTorr, The thickness of depositied ATO films were 600$\AA$~1100 $\AA$ ranges. The resistivity of ATO films was decreased due to the increase of the crystallinity of ATO films with deposition temperature. The decrease of carrier concentration of films with the increase of oxygen flow rate and working pressure is responsible for the increase of resistivity. Increasing of sputtering power raised the resistivity of films by decreasing the carrier mobility.