• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 춘계학술발표대회 논문집
• /
• pp.270-274
• /
• 2004

Aircraft composite structure with honeycomb core experiences core crush problem in manufacturing. To prevent core crush additional processes are needed such as core stabilization and prepreg material tie-down and this is the cause of increasing cost. Recent study shows that high friction prepreg prevent core crush without additional process. This paper presents the analysis of high frictional material which attracts lots of interests through physical property, mechanical property and microscopic morphology and the cause of friction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.264-267
• /
• 2005

Soft magnetic iron powders have been coated with polyester or phenol resin. And the coated powder (soft magnetic composite) have been pressed into ring type core over the pressure of 870 MPa. Green density, magnetic flux density, permeability, core loss of the samples were measured to look at the effect of the coating materials and the amount of them. Green density is increased with the amount of coating materials and shows the maximum value, 6.5 $g/cm^3$ at 5 w/o, but decreased over it. And lowest value of the core loss is showed for the 5 w/o coated samples.

• 한국전기전자재료학회논문지
• /
• 제20권11호
• /
• pp.995-999
• /
• 2007

We investigated the characteristics of a flux-lock type superconducting fault current limiter(SFCL) considering magnetization characteristic of iron core. The flux-lock type SFCL, like other types of SFCLs using the iron core, undergoes the saturation of the iron core during the initial fault time. Therefore, if the design to prevent the saturation of the iron core is considered, the effective fault current limiting operation can be achieved. Through the analysis for its equivalent circuit including the magnetization characteristic of the iron core, the limiting impedance of the flux-lock type SFCL was drawn. The magnetization currents and the limited currents of SFCL, which were dependent on the winding direction and the turns' ratio between two coils, were investigated from the short circuit experiment. It was confirmed that their experimental results agreed with the analysis ones.

• 마이크로전자및패키징학회지
• /
• 제13권2호
• /
• pp.1-7
• /
• 2006

본 논문에서는 솔더 레지스트(solder resist)의 두께와 코어의 물성에 따른 인쇄회로기판의 철의 크기와 형상에 대하여 연구하였다. 인쇄회로기판의 굽힘 변형은 적층되는 재료의 열팽창계수의 차이에 의해 발생한다. 따라서 굽힘 변형의 감소를 위해서는 열팽창계수의 차이가 작은 적층 재료를 사용하는 것이 필요하며, 구조 형상에서도 상면과 하면의 불균일성을 완화시킬 필요가 있다. 또한, 적층 재료에서 코어의 강성을 높여 점의 발생을 억제할 수 있다. 코어를 이루는 복합재료는 적층 순서와 섬유 각에 따른 물성 특성의 방향성에 따라 굽힘과 비틀림이 연성되는 현상을 보이며, 이와 같은 성질을 이용하면 휨을 제어할 수 있다. 본 연구에서는 2층으로 구성된 chip scale package (CSP) 기판의 휨에 대한 연구로, 실험 및 유한 요소해석 툴을 이용하여 개선 결과를 도출하였다.

• Elastomers and Composites
• /
• 제51권4호
• /
• pp.275-279
• /
• 2016

Additive manufacturing or 3D printing is a new manufacturing process and its application is getting growth. However, the product qualities such as mechanical strength, dimensional accuracy, and surface quality are low compared with conventional manufacturing process such as molding and machining. In this study not only mechanical characteristics of polymer sandwich panel having three dimensional core layer but also mechanical characteristics of core layer itself were analyzed. The shape of three dimensional core layer was pyramidal kagome structure. This core layer was fabricated by two different methods, injection molding with PP resin and material jetting type 3D printing with acrylic photo curable resin. The material for face sheets in the polymer sandwich panel was PP. Maximum load, stiffness, and elongation at break were examined for core layers fabricated by two different methods and also assembled polymer sandwich panels. 3D printed core showed brittle behavior, but the brittleness decreased in polymer sandwich panel containing 3D printed core. The availability of 3D printed article for the three dimensional core layer of polymer sandwich panel was verified.

• 한국주조공학회지
• /
• 제17권4호
• /
• pp.402-410
• /
• 1997

Developing a salt core for squeeze casting process, two different salt cores(pure salt core and mixed salt core) were fabricated and investigated. Pure salt core was composed of 100% NaCl and mixed salt core was made by mixtures of NaCl with MgO(1%), $Na_2B_4O_7$(2%), and talc(1%) as a binder or a strengthening agent. Salt cores were compacted to various theoretical density, heat treated, and then squeeze-cast with molten Al alloy(AC8A). The compression strength of salt cores were measured and the squeeze-cast products were examined for shape retention, infiltration of molten metal into the cores, and microstructures. The shape of salt core compacted at above 75% of the theoretical density was maintained stably. The higher theoretical density of salt cores gave higher compression strength, and the compression strength of mixed salt core was higher than that of pure salt core. Namely at 90% theoretical density, the compression strength of mixed salt core was $6.3 kg/mm^2$, compared to $4.6 kgmm^2$ for pure salt core. At a squeeze casting pressure of $1000 kg/cm^2$, molten Al alloy was infiltrated into pure salt core of under 85% of the theoretical density. At squeeze casting pressure of $1000 kg/cm^2$, only mixed salt core above 90% of the theoretical density were valid, but the shape of the core was altered in the case of pure salt core at 90% of theoretical density. A key factor for developing a salt core for squeeze casting process was estimated as the ultimate compressive strength of salt core.

• 한국결정성장학회지
• /
• 제21권2호
• /
• pp.55-59
• /
• 2011

Mong Hsu rubies from Myanmar include typically the dark core and blue patch but most of the previous research has merely focused on the dark core. This work is aimed to understanding clearly the characteristic of the dark core and blue patch of Mong Hsu rubies. It was found from the FTIR analysis that the dark core and blue patch region showed the absorption peaks of boehmite ($1986\;cm^{-1}$), diaspore ($2115\;cm^{-1}$) and water ($3400{\sim}3900\;cm^{-1}$) but the absorption peaks of O-H stretching ($3309\;cm^{-1}$ and $3078\;cm^{-1}$) were found only in blue patch region. The UV-VIS-NIR analysis of the dark core region revealed the stronger absorption of $Cr^{3+}$ at 405 and 554 nm compared to the blue patch region. In range of 600~800 nm, the UV absorption characteristic at 659, 675 and 693 nm assigned to $Cr^{3+}$ of core group samples is distinct from that of blue patch. The SEM-EDS examinations disclosed the existence of lots of micro-cracks and pores in the core regions compared to blue patch region.

• 한국정밀공학회지
• /
• 제26권11호
• /
• pp.116-123
• /
• 2009

The elastic properties of core affect mechanical properties and deformation behaviours of the lightweight sandwich panel. The objective of the present paper is to estimate experimentally Young's and shear moduli of a core in internally structured boned (ISB) panel with woven metal as inner structures using the deflection theory of sandwich beam considered core stiffness. Three points bending experiments were performed to obtain force-deflection curves of the designed ISB panel in each material direction. The elastic and shear moduli of the core in each material direction were estimated from slopes and intercepts of relationships between compliance per the span length and square of the span length, respectively. The results of the estimation showed that the fabric technology of the woven metal affects the variation of the elastic properties in the core. Through the comparison of shear moduli and force-deflection curves of the proposed method and those without considering the core stiffness, it was shown that the core stiffness should be considered to estimate properly the Young's and shear moduli of ISB panels. Finally, the contribution ratio of bending and shear deflections of ISB panels to the total deflection was quantitatively examined.

• 대한심미치과학회지
• /
• 제27권2호
• /
• pp.75-81
• /
• 2018

본 연구의 목적은 기존의 다른 포스트-코어 재료와의 유한요소분석(FEA)의 비교를 통한 치과용 포스트-코어 재료로서의 고성능 폴리머 PEKK의 생체역학 및 장기 안전성을 평가하는 데 있다. 상악 중절치를 모델링 하였으며, 구개 표면에서 치아의 장축에 $45^{\circ}$의 각도로 50N의 반복 하중을 가했다. 전통적으로 사용 된 포스트 코어 재료와 비교하기 위해 3가지 재료 (금, 유리 섬유 및 PEKK)를 시뮬레이션하여 결과를 상호 비교 해 보았다. 상아질보다 낮은 탄성 계수를 갖는 PEKK는 종래의 포스트 코어 재료보다 비교적 치근에 유리한 응력 분포를 보여 주었다. 그러나, PEKK 포스트-코어 시스템은 금속 또는 유리 섬유 포스트-코어 시스템보다 장기간의 반복하중에 대해 타락 및 크라운 파손의 가능성이 더 높을 가능성이 있다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2014년도 임시총회 및 하계학술연구발표회
• /
• pp.148-148
• /
• 2014