• Journal of Powder Materials
• /
• v.9 no.2
• /
• pp.124-132
• /
• 2002

Nano Cu powders, synthesized by Pulsed Wire Evaporation (PWE) method, have been compacted by Magnetic Pulsed Cojpaction(MPC) method. The microstructure and mechanical properties were analyzed. The optimal condition for proper mechanical properties with nanostructure was found. Both pure nano Cu powders and passivated nano Cu powders were compacted, and the effect of passivated layer on the mechanical properties was investigated. The compacts by MPC, which had ultra-fine and uniform nanostructure, showed higher density of 95% of theoretical density than that of static compaction. The pur and passivated Cu compacted at $300^{\circ}C$ exhibited maximum hardnesses of 248 and 260 Hv, respectively. The wear resistance of those compacts corresponded to the hardness.

• Korean Journal of Materials Research
• /
• v.3 no.2
• /
• pp.103-110
• /
• 1993

Abstract It has been attempted to make the copper-graphite composites by deposition of copper on the surface of graphite through the hydrogen reduction of copper chlorides. Both KISH and natural graphites of less than 325 mesh were used as substrates and the hydrogen reduction also was conducted in the range of 350-50$0^{\circ}C$. The distribution of copper on the surface of graphite was found to increase with the decrease of reduction temperature. In addition. the partial pressure of hydrogen played an important role in the overall rate of reduction which was substantially dominated by the chemical reaction on the surface of each particle. It was concluded that the reduction temperature should be maintained as low as possible to accomplish the well distribution of copper in the composites.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.315-316
• /
• 2006

The paper presents some results regarding the obtaining of some copper heat pipes with a porous copper internal layer for electronic components cooling. The heat pipes were realized by sintering of spherical copper powders of $90{\div}125\;{\mu}m$ size directly on the internal side of a copper pipe of 18 mm in diameter. The obtained pipes were then brazed in order to obtain a heat pipe of 0.5 m in length. After that, the heat pipe was sealed and filled with a small quantity of distilled water as working fluid. To establish the total heat transport coefficient and the thermal flow transferred at the evaporator, some external devices were realized to allow the heating of the evaporator and the cooling of the condenser. Water heat pipes are explored in the intermediate temperature range of 303 up to 500 K. Test data are reported for copper water heat pipe, which was tested under different orientations. The obtained results show that the water heat pipe has a good thermal transfer performance in the temperatures range between 345 and 463 K.

• Journal of Powder Materials
• /
• v.12 no.6 s.53
• /
• pp.441-446
• /
• 2005

The copper oxide nano powders were synthesized by levitational gas condensation (LGC) method, and were applied to catalyst to fabricate 3,4-dihydropyrimidin-2-(1H)-one. Processes of adsorption of Biginelli reaction reagents on the copper nanooxide surface $Cu_2O{\circ}CuO$ were studied by IR-spectroscopy. It was shown that benzaldehyde coordination, acetoacetic ether on the oxide surface is carried out with participation of carbonyl fragments, urea by N-H bonds which affects positively on the reagents reactivity.

• Journal of Powder Materials
• /
• v.7 no.1
• /
• pp.50-54
• /
• 2000

In order to reduce the sintering temperature of iron based sintered parts, sinteing properties of iron-copper prealloyed powder were investigated at various temperatures in the range of 700∼890$^{\circ}C$, and than the rusults were compared with those of the conventional iron-copper-tin compact using elemental powders, The using of prealloyed as a new process improved its sintering performance at lower temperature than elemental powder as the conventional process. The relative sintered density and radial crushing stength of the compact using prealloyed were higher than those of using elemental powder at all sintering temperature. For example, the radial curength of the compact using powder was about 50kg/mm2 at 700$^{\circ}C$, while that of the compact using elemental powder sintered at 890$^{\circ}C$ was 43kg/mm2.

• Journal of Powder Materials
• /
• v.3 no.3
• /
• pp.153-158
• /
• 1996

The exhaust gas from vehicle engines and industrial boilers contains considerable amount of harmful nitrogen monoxide(NO) which causes air pollusion and acid rain. To remove NO catalytic reduction processes using Cu ion exchanged ZSM-5 zeolite have been widely studied. In this study, an attempt was made to fabricate Cu/zeolite catalyst by using high energy ball mill. The catalytic performance of ball milled Cu/ZSM-5 zeolites is analyzed and optimum copper contents was determined. The processing variables were reaction temperature and copper contents. Complete removal of NO gas was obtained at the temperature of 553 K on 10wt.% CU/ZSM-5 mechanically alloyed composite powders. Mechanically alloyed CU/ZSM-5 catalyst showed homogeneous distribution of Cu in ZSM-5.

• Korean Journal of Materials Research
• /
• v.11 no.10
• /
• pp.863-868
• /
• 2001

The present study was carried out to investigate the effect of MA processing variables on the microstructural properties of composite powders and the coefficient of thermal expansion of pulse electric current sintered AlN-Cu powder compacts. The AlN-Cu powders had a size of less than 15 $\mu\textrm{m}$ with 25 nm size of copper crystallite after MA 32 hours. The finely distributed AlN-Cu powder compacts were completely achieved after PECS. The residual oxygen was considerably removed after hydrogen reduction treatment. The residual carbon was completely removed to 97%. The CTE of AlN-Cu powder compacts showed a good consistency with Kingery-Tuner model when the volume fraction of copper was less than 60%. When it was more than 60%, the CTE had a good agreement with Series model.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.171-178
• /
• 2004

Effects of liquid phase and reinforcing particle morphology on the sintering of Al-6 wt％Cu-10 vol％ $Al_2O_3$ or SiC particles were studied in regards to densification, structure and transverse rupture properties. The Al-Cu liquid phase penetrated the boundaries between the aluminum matrix powders and the interfaces with reinforcing particles as well, indicating a good wettability to the powders. This enhanced the densification during sintering and the resulting strength and ductility. Since most of the copper added, however, was dissolved in the liquid phase and formed a brittle $CuAl_2$ phase upon cooling rather than alloyed with the aluminum matrix, the strengthening effect by the copper was not fully realized. Reinforcing particles of agglomerate type were found less suitable for the liquid phase sintering than solid type particles. $Al_2O_3$ and SiC particles protluced little difference on the sintering behavior but their size had a large effect. Repressing of the sintered composites increased density and bending properties but caused debonding at the matrix-particle interfaces and also fracturing of the particles.

• Journal of the Korean Ceramic Society
• /
• v.43 no.10 s.293
• /
• pp.646-652
• /
• 2006

Several oxynitride glasses were fabricated by means of adding $Si_3N_4$ powders as nitrogen source to Ca-Al-Si-O-N (CAS) and Mg-Al-Si-O-N (MAS) glass powders, and heat-treated in graphite crucible at 1600$^{\circ}C$ for 1 h. The physical and mechanical properties as well as impact resistance were generally increased and compared with each other. The impact resistance properties of those manufactured glasses were evaluated by DOP (depth of penetration) method which is a way to analyze armor materials. There were two means to be used herein; the copper jet impacted at hyper velocity by exploding K2l5 warhead and tungsten heavy alloy (WHA) impact bar at high velocity by firing in 30 mm solid propellent gun. The impact resistance properties against copper jet were increased and then decreased with increasing nitrogen content, while those against WHA bar were not changed apparently with nitrogen content.

• Journal of Power System Engineering
• /
• v.21 no.4
• /
• pp.94-99
• /
• 2017

Single walled carbon nanotubes were mixed with various metal powders by mechanical ball milling and sintered by spark plasma sintering processes. Two compositional (0.1 and 1 vol%) of the single walled carbon nanotubes were dispersed onto the pure aluminum, 5052 aluminum alloy, pure titanium, Ti6Al4Vanadium alloy, pure copper, and stainless steel 316L. Each composite powders were spark plasma sintered at $600^{\circ}C$ and well synthesized regardless of the matrices. Vickers hardness of the composite materials was measured and they exhibited higher values regardless of the carbon nanotubes composition than those of the pure materials. Moreover, single walled carbon nanotubes reinforced copper matrix composites showed highest enhancement between the other metal matrices system. We believe that low energy mechanical ball milling and spark plasma sintering processes are useful tool for fabricating of the carbon nanotubes-reinforced various metal matrices composite materials. The single walled carbon nanotubes-reinforced various metal matrices composite materials could be used as an engineering parts in many kind of industrial fields such as aviation, transportation and electro technologies etc. However, detail strengthening mechanism should be carefully investigated.