• Journal of Animal Science and Technology
• /
• v.50 no.1
• /
• pp.19-26
• /
• 2008

Heritability and genetic correlation for growth traits in Duroc pig breed were estimated using Bayesian method via Gibbs sampling. The data set consisted of 3,526 performance records at National Institute of Animal Science. For estimating those parameters using Gibbs sampling, 5,000 cycles of ‘burn-in’ period were discarded among a total of 55,000 samples. Out of the remaining 50,000 samples, 5,000 estimates by each parameter were retained and used for analyses to avoid any correlation among adjacent samples. The growth traits considered in this study were average daily gain at 30kg(ADG1), average daily gain at 90kg(ADG2), backfat thickness(BF), days to 90kg(D90) and feed conversion ratio(FC). The estimated heritabilities and their standard deviation using Gibbs sampler were 0.43±0.04, 0.49±0.038, 0.31±0.040, 0.48±0.039 and 0.62±0.086, respectively. Genetic correlations were －0.02, －0.13, －0.55 and －0.15 between ADG1 with ADG2, BF, D90 and FC, respectively, 0.16, －0.73, －0.32 between ADG2 with BF, D90 and FC respectively, 0.01, －0.08 between BF with D90, FC, respectively, and 0.23 between D90 with FC.

• Journal of Hydrogen and New Energy
• /
• v.22 no.3
• /
• pp.386-401
• /
• 2011

Mathematical models for various steps in coal gasification reactions were developed and applied to investigate the effects of operation parameters on dynamic behavior of gasification process. Chemical reactions considered in these models were pyrolysis, volatile combustion, water shift reaction, steam-methane reformation, and char gasification. Kinetics of heterogeneous reactions between char and gaseous agents was based on Random pore model. Momentum balance and Stokes' law were used to estimate the residence time of solid particles (char) in an up-flow reactor. The effects of operation parameters on syngas composition, reaction temperature, carbon conversion were verified. Parameters considered here for this purpose were $O_2$-to-coal mass ratio, pressure of reactor, composition of coal, diameter of char particle. On the basis of these parametric studies some quantitative parameter-response relationships were established from both dynamic and steady-state point of view. Without depending on steady state approximation, the present model can describe both transient and long-time limit behavior of the gasification system and accordingly serve as a proto-type dynamic simulator of coal gasification process. Incorporation of heat transfer through heterogenous boundaries, slag formation and steam generation is under progress and additional refinement of mathematical models to reflect the actual design of commercial gasifiers will be made in the near futureK.

• Journal of Ocean Engineering and Technology
• /
• v.26 no.3
• /
• pp.33-38
• /
• 2012

The aim of this experimental study was to analyze the effect of the shape parameters and chamber pressure of a land-based oscillating water column (OWC) in regular incident waves. The magnitude of the free surface elevations inside the chamber was measured in a two-dimensional wave tank for various chamber skirt drafts and bottom slope angles. The surface elevations were also measured under both open chamber and partially open chamber conditions. From these measurements, the optimum shape of the OWC device could be predicted for the maximum wave energy conversion efficiency. It was found that the resonance frequency of the OWC system associated with incident waves moved toward the long wave region with increments of the draft of the chamber skirt and bottom slope. The behavior of the free surface elevation inside the chamber was also found to be dependent on the chamber pressure.

• Asian-Australasian Journal of Animal Sciences
• /
• v.11 no.4
• /
• pp.455-461
• /
• 1998

This study was proposed to investigate effects of inclusion of Chinese milk vetch silage (MVS) and rapeseed meal (RSM) on the growth and rumen fermentation of Hu-sheep. Fifty weanling lambs were randomly divided into five equal groups and offered ammoniated rice straw (ABRS) ad libitum along with 100 g concentrate (Trial 1). The animals in $T_0$, $T_1$, $T_2$, $T_3$ and $T_4$ group were respectively supplemented with MVS at levels of 0, 0, 7, 14 or 21% and with RSM at levels of 0, 15, 10, 5 or 0%. Daily gain of lambs was significantly (p<0.05) higher in $T_1$, $T_2$ and $T_3$ group than that in $T_0$ and $T_4$ group. Feed conversion ratio was greatly reduced in supplemented groups as compared with $T_0$ group. In trial 2, five sheep with rumen cannulae were used in a $5{\times}5$ Latin square design. The experimental treatments were as described in Trial 1, but without concentrate. The intake of AVRS was significantly (p<0.05) lower in $T_4$ group than that in $T_0$ group, and also significantly (p<0.05) lower than those in $T_1$ and $T_2$ group. Little difference among all treatments was found in 48h DM degradability of ABRS, MVS and RSM, and in rumen pH value and microbial protein concentration. Rumen concentrations of individual and total VFA tended to be higher in supplemented groups than those in $T_0$ group.These rusults suggest that supplementation with RSM or RSM plus MVS can effectively improve the performance of lambs, and may fail to influence markedly the rumen digestion of ABRS and rumen environments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.160-160
• /
• 2016

In this study, we applied the low temperature curing Ag paste to replace PVD System. The electrode formation of low temperature curing Ag paste for silicon Hetero-junction solar cells is important for improving device characteristics such as adhesion, contact resistance, fill factor and conversion efficiency. The low temperature curing Ag paste is composed various additives such as solvent, various organic materials, polymer, and binder. it depends on the curing temperature conditions. The adhesion of the low temperature curing Ag paste was decided by scratch test. The specific contact resistance was measured using the transmission line method. All of the Ag electrodes were experimented at various curing temperatures within the temperature range of $160^{\circ}C-240^{\circ}C$, at $20^{\circ}C$ intervals. The curing time was also changed by varying the conditions of 10-50min. In the optimum curing temperature $200^{\circ}C$ and for 20 min, the measured contact resistance is $19.61m{\Omega}cm^2$. Over temperature $240^{\circ}C$, confirmed bad contact characteristic. We obtained photovoltaic parameter of the industrial size such as Fill Factor (FF), current density (Jsc), open-circuit voltage (Voc) and convert efficiency of up to 76.2%, 38.1 mA/cm2, 646 mV and 18.3%, respectively.

• Journal of Power Electronics
• /
• v.15 no.5
• /
• pp.1305-1317
• /
• 2015

Distributed generation systems (DGSs) have been getting more and more attention in terms of renewable energy use and new generation technologies in the past decades. The self-excited induction generator (SEIG) occupies an important role in the area of energy conversion due to its low cost, robustness and simple control. Unlike synchronous generators, the SEIG has to absorb capacitive reactive power from the outer device aiming to stabilize the terminal voltage at load changes. This paper presents a novel static VAR compensator (SVC) called a magnetic energy recovery switch (MERS) to serve as a voltage controller in SEIG powered DGSs. In addition, many small scale SEIGs, instead of a single large one, are applied and devoted to promote the generation efficiency. To begin with, an expandable mathematic model based on a d-q equivalent circuit is created for parallel SEIGs. The control method of the MERS is further improved with the objective of broadening its operating range and restraining current harmonics by parameter optimization. A hybrid control strategy is developed by taking both of the stand-alone and grid-connected modes into consideration. Then simulation and experiments are carried out in the case of single and double SEIG(s) generation. Finally, the measurement results verify that the proposed DGS with SVC-MERS achieves a better stability and higher feasibility. The major advantages of the mentioned variable reactive power supplier, when compared to the STATCOM, include the adoption of a small DC capacitor, line frequency switching, simple control and less loss.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.12 no.4
• /
• pp.311-316
• /
• 2002

Difficulties of the level control in the steam generator are increased due to their nonlinear characteristics. Futhermore, parameter uncertainties of the steam generator is related with control performance and stability. The efficiency of digital conversion in control systems is proved in many recent researches. In order to solve this problem, this paper suggests robust digital fuzzy controller design methodologies of the steam generator which have unstable parameters. Takagi-Sugeno (TS) fuzzy model is used to construct a fuzzy model which has uncertainties in the steam generator. In designing procedure, intelligent digital redesign method is used to control the nonlinear system. This digital controller keeps the performance of the analog controller. Simulation examples are included for ensuring the proposed control method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.1
• /
• pp.900-905
• /
• 2015

DeNOx catalysts composed of Mn, Cu and $TiO_2$ were prepared and tested for $NH_3$-SCR. The performance of each catalyst was studied for the NOx removal efficiency while changing the calcination temperature, reaction time, and oxygen concentration. The hydrogen conversion efficiency of a calcined catalyst was measured at the $H_2$-TPR system. The change in the specific surface area of catalyst according to the calcination temperature was analyzed. As a result, the proper calcination temperature was approximately $300^{\circ}C$. If the calcination temperature is increased to $500^{\circ}C$, the NOx removal efficiency of Mn and Cu constituents is largely decreased at the low temperature range. Oxygen in flue gas is an important parameter in the SCR reaction and optimal oxygen concentration is approximately 8 vol.%.

• Ocean and Polar Research
• /
• v.38 no.3
• /
• pp.225-234
• /
• 2016

This project sought to conduct an economic feasibility study regarding the commercial production of bio-hydrogen by the marine hyperthermophilic archaeon, Thermococcus onnurineus NA1 using carbon monoxide-containing industrial off-gas. We carried out the economic evaluation of the bio-hydrogen production process using the raw material of steel mill by-product gas. The process parameter was as follows: $H_2$ production rate was 5.6 L/L/h; the conversion of carbon monoxide was 60.7%. This project established an evaluation criterion for about 10,000 tonne/year. Inflation factors were considered as 3%. The operating costs were recalculated based on prices in 2014. The total investment required for development was covered 30% by capital and 70% by a loan. The operation cost for the 0.5-year test and integration, and the cost for the first three months in the 50% production period were considered as the working capital in the cost estimation. The costs required for the rental of office space, facilities, and other related costs from the construction through to full-scale production periods were considered as continuing expenses. Materials, energy, waste disposal and other charges were considered as the operating cost of the development system. Depreciation, tax, maintenance and repair, insurance, labor, interest rate charges, general and administrative costs, lubrication and miscellaneous expenses were also calculated. The hydrogen price was set at US$ 4.15/kg for the economic evaluation. As a result, the process was considered to be economical with the payback period of 6.3 years, NPV of 18 billion Won and IRR of 26.7%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.3
• /
• pp.302-309
• /
• 2016

Urea-SCR system is currently regarded as promising NOx reduction technology for diesel engines. SCR system has to achieve maximal NOx conversion in combination with minimal $NH_3$ slip. In this study, model based open loop control for urea injection was developed and assessed in the European Transient Cycle (ETC) for heavy duty diesel engine. On the basis of the transient modeling, the kinetic parameters of the $NH_3$ adsorption and desorption are calibrated with the experimental results performed over the zeolite based catalyst. $NH_3$ storage or surface coverage of SCR catalyst can not be measured directly and has to be calculated, which is taken into account as a control parameter in this model. In order to reduce $NH_3$ slip while maintaining NOx reduction, $NH_3$ storage control algorithm was applied to correct the basic urea quantity. If the actual $NH_3$ surface coverage is higher than the maximal $NH_3$ surface coverage, the urea injection quantity is significantly reduced in the ETC cycle. By applying this logic, the resulting $NH_3$ slip peak can be avoided effectively. With optimizing the kinetic parameters based on standard SCR reaction, it suggests that a simplified, less accurate model can be effective to evaluate the capability of model based control in the ETC cycle.