• Journal of Aerospace System Engineering
• /
• v.11 no.6
• /
• pp.42-49
• /
• 2017

A 10kw wind turbine blade aerodynamic design was carried out using the self-developed program AeroDA. The concept, basic shape, and optimization were designed and verified. A performance analysis was carried out and the key factors in each design stage are summarized. In addition, a guide for the placement of cross-section airfoils constituting the blades is presented, and the importance of the stall margin test as a method of verifying aerodynamic design is summarized. In order to verify the design program AeroDA, we compared the results of the performance analysis with a specialized program DNVGL_Bladed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.330-339
• /
• 2008

Ground-based interceptors(GBI) comprise a major element of the strategic defense against hostile targets like Intercontinental Ballistic Missiles(ICBM) and reentry vehicles(RV) dispersed from them. An optimum design of the subsystems is required to increase the performance and reliability of these GBI. Propulsion subsystem design and optimization is the motivation for this effort. This paper describes an effort in which an entire GBI missile system, including a multi-stage solid rocket booster, is considered simultaneously in a Genetic Algorithm(GA) performance optimization process. Single goal, constrained optimization is performed. For specified payload and miss distance, time of flight, the most important component in the optimization process is the booster, for its takeoff weight, time of flight, or a combination of the two. The GBI is assumed to be a multistage missile that uses target location data provided by two ground based RF radar sensors and two low earth orbit(LEO) IR sensors. 3Dimensional model is developed for a multistage target with a boost phase acceleration profile that depends on total mass, propellant mass and the specific impulse in the gravity field. The monostatic radar cross section (RCS) data of a three stage ICBM is used. For preliminary design, GBI is assumed to have a fixed initial position from the target launch point and zero launch delay. GBI carries the Kill Vehicle(KV) to an optimal position in space to allow it to complete the intercept. The objective is to design and optimize the propulsion system for the GBI that will fulfill mission requirements and objectives. The KV weight and volume requirements are specified in the problem definition before the optimization is computed. We have considered only continuous design variables, while considering discrete variables as input. Though the number of stages should also be one of the design variables, however, in this paper it is fixed as three. The elite solution from GA is passed on to(Sequential Quadratic Programming) SQP as near optimal guess. The SQP then performs local convergence to identify the minimum mass of the GBI. The performance of the three staged GBI is validated using a ballistic missile intercept scenario modeled in Matlab/SIMULINK.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.32 no.4
• /
• pp.241-247
• /
• 2019

A band gap refers to a certain frequency range where the propagation of mechanical waves is prohibited. This work focuses on engineering three-dimensional Kelvin lattices having external band gaps at low audible frequency ranges using a gradient-based design optimization method. Elastic wave propagation in an infinite periodic lattice is investigated by employing the Bloch theorem. We model the ligaments using a shear-deformable beam model obtained by consistent linearization in a geometrically exact beam theory. For a given lattice topology, we enlarge band gap sizes by controlling the configuration of the beam neutral axis and cross-section thickness that are smoothly parameterized by B-spline basis functions within the isogeometric analysis framework.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.3
• /
• pp.311-320
• /
• 2021

The study looked at a cross section of inter-Korean sports through the lives of female north korean defector. The researcher was a north korean national team player in the early and mid-1990s and defected to the north and played for the national team in South Korea. After her retirement, she became a coach, but felt limited and left the sports world. After analyzing the informant's interviews, the prevailing idea was that she was always politically used, and there was a regret that he was spotlighted as a defector rather than an athletic skill. And she was not in a position to choose between South Korea and North Korea. It was also shown that inter-Korean sports exchanges could not be developed unless economic conditions were supported. As a stranger, the research participants felt alienated and adapted to South Korea. Her life is an example of experiencing inter-Korean sports at the same time, and it is believed that she can have personal, specific, and concrete characteristics while showing universality in the upcoming era of unification.

• Journal of Korea Water Resources Association
• /
• v.54 no.10
• /
• pp.819-833
• /
• 2021

This study is to evaluate applicability of linkage modeling using PHABSIM (Physical Habitat Simulation System) and SWAT (Soil and Water Assessment Tool) and to estimate ecological flow for target fishes of Andong downstream (4,565.7 km²). The SWAT was established considering 2 multi purpose dam (ADD, IHD) and 1 streamflow gauging station (GD). The SWAT was calibrated and validated with 9 years (2012 ~ 2020) data of 1 stream (GD) and 2 multi-purpose dam (ADD, IHD). For streamflow and dam inflows (GD, ADD and IHD), R², NSE and RMSE were 0.52 ~ 0.74, 0.48 ~ 0.71, and 0.92 ~ 2.51 mm/day respectively. As a result of flow duration analysis for 9 years (2012 ~ 2020) using calibrated streamflow, the average Q185 and Q275 were 36.5 m³/sec (-1.4%) and 23.8 m³/sec (0%) respectively compared with the observed flow duration and were applied to flow boundary condition of PHABSIM. The target stream was selected as the 410 m section where GD is located, and stream cross-section and hydraulic factors were constructed based on Nakdong River Basic Plan Report and HEC-RAS. The dominant species of the target stream was Zacco platypus and the sub-dominant species was Puntungia herzi Herzenstein, and the HSI (Habitat Suitability Index) of target species was collected through references research. As the result of PHABSIM water level and velocity simulation, error of Q185 and Q275 were analyzed -0.12 m, +0.00 m and +0.06 m/s, +0.09 m/s respectively. The average WUA (Weighted Usable Area) and ecological flow of Zacco platypus and Puntungia herzi Herzenstein were evaluated 76,817.0 m²/1000m, 20.0 m³/sec and 46,628.6 m²/1000m, 9.0 m³/sec. This results indicated Zacco platypus is more adaptable to target stream than Puntungia herzi Herzenstein.

• Journal of the Korean earth science society
• /
• v.31 no.4
• /
• pp.354-369
• /
• 2010

The synoptic and kinematic characteristics of a heavy rainfall that occurred in Gangneung region on 22 to 24 October 2006 were investigated using weather maps, infrared images, AWS observation data and NCEP global final analyses data. The total amount of rainfall observed in the region for the period was 316.5 mm, and the instanteneous maximum wind speed was $63.7m\;s^{-1}$. According to the analysis of weather maps, before the starting of the heavy rainfall, an extratropical low pressure system was developed in the middle region of the Korean Peninsula, and an inverted trough was formed in the northern region of the peninsula. In addition, a jet stream on the upper charts of 300 hPa was located over the Yellow Sea and the southern boundary of the peninsula. A cutoff low in the cyclonic shear side of the upper jet streak, which was linked to an anomaly of isentropic potential vorticity, was developed over the northwestern part of the peninsula. And there are analyzed potential vorticity and wind, time-height cross section of potential vorticity, vertical air motion, maximums of the divergence and convergence and vertical distribution of potential temperature in Gangneung region. The analyzed results of the synoptic conditions and kinematic processes strongly suggest that the tropopause folding made a significant role of initializing the heavy rainfall.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.16 no.3
• /
• pp.115-125
• /
• 2013

The systematic management of river is difficult due to various environmental factors such as season and terrain deformation. Especially, river terrain are rapidly changing by natural and anthropogenic factors such as torrential rain during the summer and river development projects. Thus in this conditions, building the advanced river management system is an essential condition to support the ongoing management of survey data and to acquire data regularly through river terrain survey in order to maintain an active river. The need to build an efficient system have been increased through the enhancement and advancement of River Management Geographic Information Systems(RIMGIS). In this study, database design system and Riverbed Change Data Management Program was developed for systematic management of new river terrain survey data and the efficient use of river data dynamic changes. The key features are construction of river survey data, cross and longitudinal section monitoring and analysis of riverbed change data. Maintenance tasks which can be utilized in river-based architecture was constructed. The expected results are to be able to manage river systematically, and utilization of river topographic survey data efficiently for river maintenance work.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.35 no.6
• /
• pp.128-137
• /
• 2023

In this study, the bearing pressure on the rubble mound of a gravity-based harbor structure with an arbitrarily shaped bottom was targeted. Assuming that the bottom of the structure is a rigid body, the rubble mound was modeled as a linear spring uniformly distributed on the bottom that resists compression only, and the bearing pressure evaluation formula was derived. It was confirmed that there were no errors in the derivation process by showing that when the bottom was square, the derived equation was converted to the equation used in the design. In addition, the validity of the derived equation was proven by examining the behavior and convergence value of the bearing pressure when an arbitrarily shaped bottom converges into a square one. In order to examine the adequacy of the method used in the current design, the end bearing pressure for the pre-designed breakwater cross-section was calculated and compared with the values in the design document. As a result, it was shown that the method used for design was not appropriate as it gave unsafe results. In particular, the difference was larger when the eccentricity of the vertical load was large, such as in the case of extreme design conditions.