• 폴리머
• /
• 제25권1호
• /
• pp.63-70
• /
• 2001

대표적 가교형태 변화에 따른 유사한 stress-strain 특성을 나타내는 조건하에서 공정특성 및 전반적 물성에 미치는 영향을 조사하였다. 천연고무 기본 배합에서 촉진제나 황 공여체(sulfur donor) 증가에 따라 induction time은 길어지나, 가류속도는 빨라졌다. 가교계 변화에 따른 인장강도의 영향은 매우 적은 반면 신장율은 conventional vulcanization (CV)계에서 efficient vulcanization (EV)계로 갈수록 감소하는 경향을 보여 주었다. Blow-out이 발생하는 시간을 가교형태에 따라 비교하여 보면 CV

• 한국염색가공학회지
• /
• 제35권4호
• /
• pp.246-255
• /
• 2023

In this study, we investigated for natural rubber foam to replace petrochemical-based neoprene foam. Experiments were conducted on vulcanization system and 2-step foaming process of natural rubber. The vulcanization system were EV(Efficient Vulcanization Cure), Semi-EV(Semi-Efficient Vulcanization Cure) and CV(Conventional Vulcanization Cure). In the 2-step foaming process, first molding temperature was 140℃, times were 15, 20, 25, and 30minutes, and the second molding temperature was 160℃, the times 5, 10, 15, and 20minutes. The cure and viscosity characterization were evaluated by oscillating disc rheometer (ODR) and mooney viscosmeter. Various mechanical characteristics, including hardness, tensile strength, elongation at the point of rupture, and tear strength, were quantified. Subsequently, an assessment of alterations in these mechanical attributes was conducted post-immersion in a NaCl solution. In addition degree of volume change was measured after immersing the NR foam in NaCl solution and the low-temperature permanent compression set was evaluated at 4℃. And expansion ratio and shrinkage ratio of NR foam were evaluated for 28 days. As a result the EV vulcanization system showed the least change in physical properties before and after salt water immersion, and the lowest shrinkage ratio for 28 days. In addition it was confirmed that the 2-step foaming optimum condition differed depending on the appropriate vulcanization condition.

• Elastomers and Composites
• /
• 제53권3호
• /
• pp.150-157
• /
• 2018

Fatigue properties of rubber are one of the most important characteristics in the rubber industry. In this study, the fatigue properties of MREs (magneto-rheological elastomers) based on NR (natural rubber), EPDM (ethylene-propylene diene monomer), and AEM (ethylene/acrylic elastomer) were investigated. For comparison, MREs with a Shore hardness of 60A were prepared. According to the relative results, the fatigue properties of EPDM MRE were the worst. Thus, we investigated methods to improve the fatigue properties of EPDM MRE by varying the carbon black content and curing systems of EPDM as the matrix of the MRE. Dynamic properties were measured using a fatigue tester and an RPA (rubber process analyzer), and the XPS (X-ray photoelectron spectroscopy) was used to analyze the curing system of the EPDM matrix. According to the results, the Payne effect increased and the fatigue resistance decreased as the carbon black content increased. In case of the curing system, the CV (conventional vulcanization) system was superior to the EV (efficient vulcanization) system in terms of the fatigue resistance. This was because the number of flexible bonds in the case of the CV system was higher than that in the case of the EV system. However, the EV system showed excellent mechanical properties because it had many monosulfidic bonds with strong binding energy.