• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.314-316
• /
• 2001

This paper present the position control method for the application of permanent magnet linear synchronous motor. Controller is designed as a conventional P-PI controller, but the extra information is used such as velocity and acceleration from motion profiles. The profiles comes from S-Curve which is an optimized point-to-point motion profiles to achieve fast motions with minimum vibration[2]. In this application, the targets of the position control are maximum 10um position error within 10msec after respective ending point of position profiles. The implementation of the controller has been done in full digital way. All the controller is designed on the DSP TMS320VC33 control board. To prove performance of the controller, the experiment was performed with a servo linear motor.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.2
• /
• pp.189-196
• /
• 1986

Linear second-order matrix systems representing dynamics of large flexible structures are recast in a state space form. By can efficient partial decoupling technique, a few of low frequency modes are decoupled from the rest of modes, and an optimal control procedure is developed in such a way that damping is added to the selected modes without control spillover to uncontrolled modes. Since the partial decoupling requires only eigenvectors of the sected modes, the computing time can be reduced significantly in large systems. Therefore, the method of partial decoupling and control developed in this work may be applicable to vibration contorl of large flexible space structures.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1112-1118
• /
• 1990

The end tip position control of a flexible robot arm has been presented by utilizing the feedback signal from the rate-gyro mounted at the end tip. Kalmann filter and the state feedback gains were determined by optimal sense based upon the parameter from the geometrical and electrical data of the flexible arm system. The simulation and experiment were performed and it has been proved that implementation of the rate-gyro drastically improves the performance.

• Journal of Power Electronics
• /
• v.6 no.1
• /
• pp.29-37
• /
• 2006

A sensorless control for an IPM (Interior Permanent Magnet) synchronous motor in a single piston rotary compressor is presented in this study. The rotor position is estimated from the d-axis and q-axis current errors between the real system and a motor model of the position estimator. The torque pulsation of the single piston rotary compressor is compensated to reduce speed ripples, as well as, mechanical noise and vibration. The proposed sensorless drive enables the compressor to operate at a lower speed which increases energy savings and reduces mechanical noise. It also gives high speed operations by a flux weakening control for rapid air-cooling and heating of the heat pump air-conditioners.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.1
• /
• pp.75-80
• /
• 2008

This paper presents a new precision moving instrument for the displacement and direction control using the uni-morph type PZT actuator. The instrument is composed of the two-body and a link. The body has the uni-morph type PZT actuator, which make the vibration. Movement of simple moving instrument is generally analyzed by the theory of center-of-gravity moment. However the analysis of the instrument in this paper is focused the resonance of instrument. Resonance of the body is originated a uni-morph type PZT actuator that is vibrated by voltage and frequency. The basic performances of one body instrument are analyzed by the FEM analysis. And experiments are also performed to confirm the linear movement of the instrument and direction control. it is proper a voltage control than a frequency control for the direction changing. And Moving velocity is 0.032m/s.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.4
• /
• pp.449-454
• /
• 2010

The force control of a constrained flexible manipulators has been one of the major research topics. However, a little effort has been devoted for the relation between friction force and elastic deflection of end-effector for a constrained flexible manipulator. So, the aim of this paper is to clarify the friction mechanism of a constrained spatial multi-link flexible manipulator by changing the material and connected method of end-effector. In this study, a concise hybrid position/force control scheme is applied to the control of a flexible manipulator, and the experimental results for the constrained vertical motion and constrained horizontal motion is presented. Finally a comparison between these results are presented to show the reduction of vibration of link and friction force.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.4 no.2
• /
• pp.25-36
• /
• 2000

본 논문에서는 구조물이 과도한 기진력을 받을 때에 구조물의 진동 제어를 위하여 제안 되어진 여러 가지 포화 제어 알고리듬들의 유용성을 실제적인 관점에서 살펴보았다 제안된 포화 제어 알고리듬 중세서 수정된 뱅뱅 제어 알고리듬이 매우 유용한 것임을 확인할 수 있었으나 이는 제어력 파형 결정 파라미터의 어떤 범위내에서만 효과적이며 그 범위를 넘어서는 경우에 있어서는 제어기를 불안정하게 할 수 있음을 확인할 수 있었다 따라서 수정된 뱅뱅 제어 알고리듬의 적용시에 과도한 외부 기진력에 대하여 제어기의 안정적인 작동에 의한 구조물의 진동제어효과를 얻기 위해서 제어력 파형 파라미터를 과도 기진력의 크기에 따라 변화시키는 적응형의 방법을 제안하였고 이의 유용성을 수치실험 및 유압식 질량 감쇠기를 장착한 축소 구조물 검증 실험을 통하여 확인하였다.

• Wind and Structures
• /
• v.16 no.4
• /
• pp.323-340
• /
• 2013

An active mass damper system for flutter control of bridges is presented. Flutter stability of bridge structures is improved with the help of eccentric rotational actuators (ERA). By using a bridge girder model that moves in two degrees of freedom and is subjected to wind, the equations of motion of the controlled structure equipped with ERA are established. In order to take structural nonlinearities into consideration, flutter analysis is carried out by numerical simulation scheme based on a 4th-order Runge-Kutta algorithm. An example demonstrates the performance and efficiency of the proposed device. In comparison with known active mass dampers for flutter control, the movable eccentric mass damper and the rotational mass damper, the power demand is significantly reduced. This is of advantage for an implementation of the proposed device in real bridge girders. A preliminary design of a realization of ERA in a bridge girder is presented.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.840-843
• /
• 1993

In this paper, an LPM controller using microprocessor was implemented and adopted Microstep method to control the LPW. In Microstep method, current waveform is sinusoidal not square. This method is characterized by less vibrating, less noisy, and more precise position control. Also, we simulate the static thrust characteristics for each waveform. The experiment was performed according to the mechanical vibration at the acceleration mode and slewing mode. The current tracks reference sinusoidal waveform well and stability was improved as we expected. Therefore, the possibility of the open loop position control was proposed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.2
• /
• pp.335-341
• /
• 2016

In general, a yawing motion concept is used for the lateral control of one wheel robot where the gimbal system is located horizontally. In this paper, another concept of the vertically located gimbal system is presented for the same purpose. Although the vertical concept undergoes an instability more easily than the horizontal one, the pitching motion of the gyroscopic effect is considered. Firstly, the trade-off relation between two balancing concepts are investigated by comparing the gyroscopic mechanism. Secondly, the dynamic model for the problem of the proposed concept is derived using the oscillatory inverted stick model. Thirdly, the stability of the model is analyzed using the phase trajectory method. Finally, the control performance of the system by a vibration controller is simulated.