• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.1
• /
• pp.67-76
• /
• 1997

In this paper we developed a tactile feedback device using repulsive force of magnets. The force of the tactile feedback device was derived from the Maxwell's stress method by using the concept of magnetic charge. Magnetic repulsive force is linear function with respect to current and nonlinear to displacement. Experimental data shows these characteristics. To compensate the fact that the presented tactile feedback device can not be controlled by close loop control, we developed a simulation model which predicts output displacement and force by using Runge-Kutta method. And, this paper evaluated the presented tactile feedback device and compared it with commercial tactile feedback devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.5
• /
• pp.284-288
• /
• 2016

Among the various physiological information that could be obtained from human body, heartbeat rate is a commonly used vital sign in the clinical milieu. Photoplethysography (PPG) sensor is incorporated into many wearable healthcare devices because of its advantages such as simplicity of hardware structure and low-cost. However, healthcare device employing PPG sensor has been issued in susceptibility of light and motion artifact. In this paper, to develop the real-time heart rate measurement device that is less sensitive to the external noises, we have fabricated an ultra-small wireless LC resonant pressure sensor by MEMS process. After performance evaluation in linearity and repeatability of the MEMS pressure sensor, heartbeat waveform and rate on radial artery were obtained by using resonant frequency-pressure conversion method. The measured data using the proposed heartbeat rate measurement system was validated by comparing it with the data of an commercialized heart rate measurement device. Result of the proposed device was agreed well to that of the commercialized device. The obtained real time heartbeat wave and rate were displayed on personal mobile system by bluetooth communication.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.7 s.184
• /
• pp.59-66
• /
• 2006

In laser welding, automatic seam tracking is important to adjust the laser head position in real time as it moves along the seam. Also if the joint gap is occurred, filling the missing material into the joint gap is necessary to prevent welding defects and bad welding quality. In general, the joint gap width is not constant along the seam due to a variety of reason. So it is essential to control the filler wire speed into the joint gap to acquire good welding quality. This paper describes an intelligent filler wire feeding device which can control 3-dimensional seam tracking and the filler wire speed by measuring the gap position and the joint gap width in laser welding. We call this device as Smart Micro Control system(SMC). To achieve this objective, we assessed weld quality in 2mm sheets of A16061 which had various gap width by using the developed device. From the experimental results, It was found the possibility that the developed device could be used in welding various 3-dimensional structures.

• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.175-180
• /
• 2015

Worldwide, studies on intelligent vehicles for the convenience of drivers have been actively conducted as the number of cars has increased. However, vehicle convenience enabled by buttons lowers the concentration on driving and hence poses as a huge threat to the safety of the driver. The use of one of the convenient features, impaired driving auxiliary equipment, is limited because of its complex usage, and this device also hinders the front view of the driver. This paper proposes a vehicle-control device for controlling the convenient features as well as changes in speed and direction using gestures and motions of the driver. This device consists of an ultrasonic sensor for recognizing movement, an arduino for accepting signal control functions and servo and DC motors apply to various vehicle parts. Firstly, the vehicle-control device was designed using a 3D CAD program known as Solid-works based on the size of the steering wheel. Then, through simulations, a suitable length for minimizing the absorbent between ultrasonic sensors was confirmed using a program known as COMSOL Multiphysics. Finally, simulation results were verified through experiments, and the optimal size of the device was identified through the number of errors.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.6
• /
• pp.578-586
• /
• 2009

Recently, horn-type rudders are generally being used at high speed container ships and are frequently suffering from the cavitation occurs on the rudder surface in the vicinity of the gap between the horn and rudder plate. In the present study, a fluid supplying device is employed as to decrease the gap cavitation of the horn-type rudder. The device is devised to inject the water against the pressure side through the nozzle installed inside of the gap to control the gap flow. Numerical calculations are performed to investigate the effectiveness of the device and the results show that the device can noticeably reduce the gap cavitation. The rates of water injection for achievement of the maximum retardations of gap flow are also sought.

• Journal of Sensor Science and Technology
• /
• v.28 no.1
• /
• pp.52-57
• /
• 2019

Studies to augment emotion and immersion in multimedia content through olfactory stimulation are being increasingly conducted in the past two decades, and a variety of scent devices have been developed. Most of the scent devices are very large and heavy; consequently, they are installed on a table rather than being attached to the Head-mounted Display (HMD). Even if such devices are mounted on the HMD, it is not possible to control the scent density because of the size limitation, and it is not easy to be immersed in the experience because of the noise caused by the scent device. In order for an actual virtual reality or an augmented reality system to work efficiently with the scent device, three conditions - noiseless, a compact design, and concentration control- must be satisfied. In this study, we design a scent device that satisfies these three conditions. By using a miniature piezoelectric pump, a small size scent device is designed so that it can be easily attached to the lower end of the HMD, and hardly any noise is generated. Moreover, it is possible to control the concentration of the scent by controlling the piezoelectric pump using amplitude and frequency.

• Journal of Magnetics
• /
• v.19 no.2
• /
• pp.197-204
• /
• 2014

A transcranial magnetic stimulation device is a complicated appliance that employs a switching power device designed for discharging and charging a capacitor to more than 1 kV. For a simple transcranial magnetic stimulation device, this study used commercial power and controlled the firing angle using a Triac power device. AC 220V 60 Hz, the power device was used directly on the tanscranial magnetic stimulation device. The power supply device does not require a current limiting resistance in the rectifying device, energy storage capacitor or discharge circuit. To control the output power of the tanscranial magnetic stimulation device, the pulse repetition rate was regulated at 60 Hz. The change trigger of the Triac gate could be varied from $45^{\circ}$ to $135^{\circ}$. The AVR 182 (Zero Cross Detector) Chip and AVR one chip microprocessor could control the gate signal of the Triac precisely. The stimulation frequency of 50 Hz could be implemented when the initial charging voltage Vi was 1,000 V. The amplitude, pulse duration, frequency stimulation, train duration and power consumption was 0.1-2.2T, $250{\sim}300{\mu}s$, 0.1-60 Hz, 1-100 Sec and < 1 kW, respectively. Based on the results of this study, TMS can be an effective method of treating dysfunction and improving function of brain cells in brain damage caused by ischemia.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.3
• /
• pp.317-327
• /
• 2021

Low Frequency Active Sonobuoy(hereinafter referred to as LFAS) are being developed in Korea in consideration of compatibility with existing overseas sonobuoys, and a communication device for acoustic signals receiving and operating control of LFAS has been developed. The communication device needs to verify compatibility with the existing Sonobuoy, and for this purpose, the standardized Sonobuoy communication protocol was applied. The communication device is designed/manufactured to transmit the acoustic signal received in real time from the Sonobuoy through VHF band RF communication to the data processing device, and transmit CFS/CSG commands for operation control to the Sonobuoy through UHF band RF communication. In order to verify the manufactured communication device, the communication status and performance were verified by interlocking test through Ultra Electronics' PASS-II equipment and domestically developed electronic device of Sonobuoy. In addition, operability was verified through environmental tests, water tanks, and marine operations. In the future, the communication device of sonobuoy can be used for verification of the Sonobuoy developed in Korea.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.10
• /
• pp.7-13
• /
• 2015

Wearable device, next generation smart device, is consistently growing. The flexible display will be a kind of display in the wearable device. The flexible display technology is now evolving with end-user requirement such as portability and easy installation. Previous wearable display products still have some difficulties in manufacturing and in flexibility whole device. But it can be a flexible display with LED device and utilized in commercial area. In this paper, we propose a driver to control the LED display and implement a flexible LED display system.

• Proceedings of the KIPE Conference
• /
• 1999.07a
• /
• pp.270-273
• /
• 1999

This paper describes the characteristics of two methods about providing information needed for propulsion device control in train. The one is to use new way using the communication network for transmission of control information, the other is traditional way using hardwire connection. And this paper describes the communication interface technique between TCMS(Train Control and Monitoring System) and VVVF inverter system with LonWorks network adapted to SMG line 6 which has been developed. With this technique, an inertia load test carried out for the traction control environment and it is expecting a field test at SMG line 6.